SERVICE MANUAL
COLOR TELEVISION/
VIDEO CASSETTE RECORDER
FILE NO. 140-200214
MV14FM4
SERVICING NOTICES ON CHECKING
6. AVOID AN X-RAY
1. KEEP THE NOTICES
As for the places which need special attentions,
they are indicated with the labels or seals on the
cabinet, chassis and parts. Make sure to keep the
indications and notices in the operation manual.
3. USE THE DESIGNATED PARTS
5. TAKE CARE TO DEAL WITH THE
CATHODE-RAY TUBE
In the condition that an explosion-proof cathode-
ray tube is set in this equipment, safety is
secured against implosion. However, when
removing it or serving from backward, it is
dangerous to give a shock. Take enough care to
deal with it.
Safety is secured against an X-ray by consider-
ing about the cathode-ray tube and the high
voltage peripheral circuit, etc.
Therefore, when repairing the high voltage pe-
ripheral circuit, use the designated parts and
make sure not modify the circuit.
Repairing except indicates causes rising of high
voltage, and it emits an X-ray from the cathode-
ray tube.
Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.
HOW TO ORDER PARTS
PERFORM A SAFETY CHECK AFTER
SERVICING
7.
Confirm that the screws, parts and wiring which
were removed in order to service are put in the
original positions, or whether there are the
portions which are deteriorated around the
serviced places serviced or not. Check the
insulation between the antenna terminal or
external metal and the AC cord plug blades.
And be sure the safety of that.
(INSULATION CHECK PROCEDURE)
1.
2.
3.
4.
Unplug the plug from the AC outlet.
Remove the antenna terminal on TV and turn
on the TV.
Insulation resistance between the cord plug
terminals and the eternal exposure metal
[Note 2] should be more than 1M ohm by
using the 500V insulation resistance meter
[Note 1].
If the insulation resistance is less than 1M
ohm, the inspection repair should be
required.
[Note 1]
If you have not the 500V insulation
resistance meter, use a Tester.
[Note 2]
External exposure metal: Antenna terminal
Earphone jack
2. AVOID AN ELECTRIC SHOCK
There is a high voltage part inside. Avoid an
electric shock while the electric current is
flowing.
The parts in this equipment have the specific
characters of incombustibility and withstand
voltage for safety. Therefore, the part which is
replaced should be used the part which has
the same character.
Especially as to the important parts for safety
which is indicated in the circuit diagram or the
table of parts as a
mark, the designated
parts must be used.
4. PUT PARTS AND WIRES IN THE
ORIGINAL POSITION AFTER
ASSEMBLING OR WIRING
There are parts which use the insulation
material such as a tube or tape for safety, or
which are assembled in the condition that
these do not contact with the printed board.
The inside wiring is designed not to get closer
to the pyrogenic parts and high voltage parts.
Therefore, put these parts in the original
positions.
A1-1
A1-2
1.
2.
3.
4.
5.
Remove the VCR block from the main unit.
(Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.)
Remove the screw 1 of the Deck Chassis and remove the Loading Motor.
Rotate the Pinch Roller Cam in the direction of the arrow by hand to slacken the Video Tape.
Rotate the Clutch Ass'y either of the derections to wind the Video Tape in the Cassette Case.
Repeat the above step 3~4. Then take out the Video Cassette from the Deck Chassis. Be careful not to
scratch on the tape.
TAPE REMOVAL METHOD AT NO POWER SUPPLY
Pinch Roller Cam
Main Cam
Clutch Ass'y
Main Chassis (Front Side)
Loading Motor
Screw 1
Capstan DD Unit
TABLE OF CONTENTS
SERVICING NOTICES ON CHECKING .....................................................................................
HOW TO ORDER PARTS ..........................................................................................................
TAPE REMOVAL METHOD AT NO POWER SUPPLY ............................................................
TABLE OF CONTENTS ..............................................................................................................
GENERAL SPECIFICATIONS ...................................................................................................
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF MECHANICAL PARTS AND P. C. BOARDS ............................................
2. REMOVAL OF DECK PARTS ............................................................................................
3. REMOVAL OF ANODE CAP ..............................................................................................
4. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ...............................................
KEY TO ABBREVIATIONS ........................................................................................................
SERVICE MODE LIST ................................................................................................................
PREVENTIVE CHECKS AND SERVICE INTERVALS ..............................................................
WHEN REPLACING EEPROM (MEMORY) IC ..........................................................................
SERVICING FIXTURES AND TOOLS .......................................................................................
PREPARATION FOR SERVICING .............................................................................................
MECHANICAL ADJUSTMENTS ................................................................................................
ELECTRICAL ADJUSTMENTS ..................................................................................................
BLOCK DIAGRAMS
TV ............................................................................................................................................
Y/C/AUDIO/CCD/HEAD AMP .................................................................................................
MICON/OPERATION/IN/OUT ................................................................................................
HI-FI ........................................................................................................................................
PRINTED CIRCUIT BOARDS
MAIN/CRT ...............................................................................................................................
SYSCON ..................................................................................................................................
OPERATION ...........................................................................................................................
SCHEMATIC DIAGRAMS
Y/C/AUDIO/CCD/HEAD AMP .................................................................................................
MICON .....................................................................................................................................
POWER ...................................................................................................................................
IN/OUT .....................................................................................................................................
CHROMA/IF .............................................................................................................................
SOUND AMP ...........................................................................................................................
HI-FI .........................................................................................................................................
IF ............................................................................................................................................
TV POWER .............................................................................................................................
DEFLECTION ..........................................................................................................................
CRT ..........................................................................................................................................
OPERATION ...........................................................................................................................
INTERCONNECTION DIAGRAM ...............................................................................................
WAVEFORMS .............................................................................................................................
MECHANICAL EXPLODED VIEWS ...........................................................................................
CHASSIS EXPLODED VIEWS ...................................................................................................
MECHANICAL REPLACEMENT PARTS LIST .........................................................................
CHASSIS REPLACEMENT PARTS LIST ..................................................................................
ELECTRICAL REPLACEMENT PARTS LIST ...........................................................................
A1-1
A1-1
A1-2
A2-1
A3-1~A3-5
B1-1, B1-2
B2-1~B2-6
B3-1
B4-1, B4-2
C1-1, C1-2
C2-1
C3-1, C3-2
C4-1
D1-1
D1-1
D2-1~D2-4
D3-1~D3-6
E-1, E-2
E-3, E-4
E-5, E-6
E-7, E-8
F-1~F-4
F-5~F-8
F-9, F-10
G-1, G-2
G-3, G-4
G-5, G-6
G-7, G-8
G-9, G-10
G-11, G-12
G-13, G-14
G-15, G-16
G-17, G-18
G-19, G-20
G-21, G-22
G-23, G-24
G-25, G-26
H-1, H-2
I1-1, I1-2
I2-1, I2-2
J1-1
J2-1
J3-1~J3-5
A2-1
GENERAL SPECIFICATIONS
G-1
TV
CRT
CRT Size / Visual Size
14 inch
/ 357.0 mmV
System
CRT Type
Flat
Deflection
90
degree
Magnetic Field
BV/BH
+ 0.45 G
/ 0.18 G
Color System
NTSC
Speaker
2 Speaker
Position
Front
Size
1.5 x 2.5 Inch
Impedance
8
ohm
Sound Output
MAX
1.5W + 1.5W
10%(Typical)
1.5W + 1.5W
G-2
VCR
System
VHS Player / Recorder
System
Video System
NTSC
Hi-Fi STEREO
Yes
NTSC PB
-
Deck
DECK
OVD-7
Loading System
Front
Motor
3
Heads
Video Head
4 Head
FM Audio Head
2 Head
Audio /Control
Mono
/Yes
Erase(Full Track Erase)
Yes
Tape
Rec
PAL
-
Speed
NTSC
SP/SLP(EP)
Play
PAL
-
NTSC
SP/SLP(EP)
Fast Forward / Rewind Time (Approx.) at 25oC
FF:4'50"/REW:2'30"
with Cassette
T-120
Forward/Reverse
NTSC or PAL-M
SP/SLP(EP) = 3x,5x / 9x,15x
Picture Search
Frame Advance
1/10
Slow Speed
1/10
G-3
Tuning
Broadcasting System
US System M
System
Tuner and
System
1 Tuner
Receive CH
Destination
US(w/CATV)
Tuning System
F-Synth
Input Impedance
VHF/UHF 75 ohm
CH Coverage
2~69, 4A,A-5~A-1, A~I,
J~W,W+1~W+84
Intermediate
Picture(FP)
45.75MHz
Frequency
Sound(FS)
41.25MHz
FP-FS
4.5MHz
Preset CH
No
Stereo/Dual TV Sound
US-Stereo
Tuner Sound Muting
Yes
G-4
Signal
Video Signal
Input Level
1 V p-p/75 ohm
Output Level
1 V p-p/75 ohm
S/N Ratio (Weighted)
50 dB
Horizontal Resolution at SP Mode
220Line
Audio Signal
Input Level
-8dBm/50k ohm
(0dB=0.775Vrms)
Output Level
-8dBm/1k ohm
S/N Ratio at SP (Weighted)
38 dB
Harmonic Distortion (1kHz)
1.5
%
Typical
Frequency Response
at SP
100Hz - 10kHz
at LP
-
at SLP(EP)
100Hz - 4kHz
Hi-Fi Audio Signal
Dynamic Range : More than
90
dB
Wow And Flutter : Less than
0.01
%Wrms
Channel Separation : More than
60
dB
Harmonic Distortion : Less than
1.0
%
G-5
Power
Power Source
AC
120V,60Hz
DC
-
Power Consumption
at AC
81 W
at 120 V 60 Hz
at DC
-
Stand by (at AC)
3 W
at 120 V 60 Hz
Per Year
-
Protector
Power Fuse
Yes
Dew Sensor
No
G-6
Regulation
Safety
UL
Radiation
FCC
X-Radiation
DHHS
G-7
Temperature
Operation
+5oC ~ +40oC
Storage
-20oC ~ +60oC
G-8
Operating Humidity
Less then 80% RH
A3-1