SERVICE MANUAL
COLOR TELEVISION
30HF84
FILE NO. 050-200418
DOCUMENT CREATED IN JAPAN, July, 2004
SERVICING NOTICES ON CHECKING
6. AVOID AN X-RAY
1. KEEP THE NOTICES
As for the places which need special attentions,
they are indicated with the labels or seals on the
cabinet, chassis and parts. Make sure to keep the
indications and notices in the operation manual.
3. USE THE DESIGNATED PARTS
5. TAKE CARE TO DEAL WITH THE
CATHODE-RAY TUBE
Safety is secured against an X-ray by consider-
ing about the cathode-ray tube and the high
voltage peripheral circuit, etc.
Therefore, when repairing the high voltage pe-
ripheral circuit, use the designated parts and
make sure not modify the circuit.
Repairing except indicates causes rising of high
voltage, and it emits an X-ray from the cathode-
ray tube.
Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.
HOW TO ORDER PARTS
Inferior silicon grease can damage IC's and transistors.
When replacing an IC's or transistors, use only specified silicon grease (YG6260M).
Remove all old silicon before applying new silicon.
IMPORTANT
2. AVOID AN ELECTRIC SHOCK
There is a high voltage part inside. Avoid an
electric shock while the electric current is
flowing.
The parts in this equipment have the specific
characters of incombustibility and withstand
voltage for safety. Therefore, the part which is
replaced should be used the part which has
the same character.
Especially as to the important parts for safety
which is indicated in the circuit diagram or the
table of parts as a
mark, the designated
parts must be used.
4. PUT PARTS AND WIRES IN THE
ORIGINAL POSITION AFTER
ASSEMBLING OR WIRING
There are parts which use the insulation
material such as a tube or tape for safety, or
which are assembled in the condition that
these do not contact with the printed board.
The inside wiring is designed not to get closer
to the pyrogenic parts and high voltage parts.
Therefore, put these parts in the original
positions.
In the condition that an explosion-proof cathode-
ray tube is set in this equipment, safety is
secured against implosion. However, when
removing it or serving from backward, it is
dangerous to give a shock. Take enough care to
deal with it.
PERFORM A SAFETY CHECK AFTER
SERVICING
7.
Confirm that the screws, parts and wiring which
were removed in order to service are put in the
original positions, or whether there are the
portions which are deteriorated around the
serviced places serviced or not. Check the
insulation between the antenna terminal or
external metal and the AC cord plug blades.
And be sure the safety of that.
(INSULATION CHECK PROCEDURE)
1.
2.
3.
4.
Unplug the plug from the AC outlet.
Remove the antenna terminal on TV and turn
on the TV.
Insulation resistance between the cord plug
terminals and the eternal exposure metal
[Note 2] should be more than 1M ohm by
using the 500V insulation resistance meter
[Note 1].
If the insulation resistance is less than 1M
ohm, the inspection repair should be
required.
[Note 1]
If you have not the 500V insulation
resistance meter, use a Tester.
[Note 2]
External exposure metal: Antenna terminal
Earphone jack
A1-1
TABLE OF CONTENTS
SERVICING NOTICES ON CHECKING .....................................................................................
HOW TO ORDER PARTS ..........................................................................................................
IMPORTANT ...............................................................................................................................
TABLE OF CONTENTS ..............................................................................................................
GENERAL SPECIFICATIONS ....................................................................................................
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP ...............................................................................................
2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ................................................
SERVICE MODE LIST ................................................................................................................
CONFIRMATION OF HOURS USED .........................................................................................
WHEN REPLACING EEPROM (MEMORY) IC ..........................................................................
ELECTRICAL ADJUSTMENTS ..................................................................................................
BLOCK DIAGRAMS
TV .............................................................................................................................................
SOUND AMP/FRONT JACK ...................................................................................................
MICON1/STEREO ...................................................................................................................
AV/SYNC COUNT/CONNECTOR ...........................................................................................
INTERFACE .............................................................................................................................
MICON2 ...................................................................................................................................
PRINTED CIRCUIT BOARDS
MAIN ........................................................................................................................................
AV ............................................................................................................................................
HD-MI/FRONT JACK ...............................................................................................................
CRT/CONNECTOR .................................................................................................................
SCHEMATIC DIAGRAMS
CHROMA/PROGRESSIVE/PIN CUSHION ............................................................................
DEFLECTION ..........................................................................................................................
TV POWER ..............................................................................................................................
OPERATION ............................................................................................................................
SOUND AMP/FRONT AV ........................................................................................................
MICON1 ...................................................................................................................................
STEREO ..................................................................................................................................
TUNER/AV ...............................................................................................................................
REGURATOR ..........................................................................................................................
SYNC COUNT/CONNECTOR .................................................................................................
CRT/CVM .................................................................................................................................
INTERFACE .............................................................................................................................
MICON2 ...................................................................................................................................
WAVEFORMS .............................................................................................................................
MECHANICAL EXPLODED VIEWS ...........................................................................................
MECHANICAL REPLACEMENT PARTS LIST .........................................................................
ELECTRICAL REPLACEMENT PARTS LIST ...........................................................................
A1-1
A1-1
A1-1
A2-1
A3-1~A3-5
B1-1
B2-1, B2-2
C-1
C-1
C-2
D-1~D-6
E-1, E-2
E-3, E-4
E-5, E-6
E-7, E-8
E-9, E-10
E-11, E-12
F-1~F-4
F-5, F-6
F-7, F-8
F-9, F-10
G-1, G-2
G-3, G-4
G-5, G-6
G-7, G-8
G-9, G-10
G-11, G-12
G-13, G-14
G-15, G-16
G-17, G-18
G-19, G-20
G-21, G-22
G-23, G-24
G-25, G-26
H-1~H-4
I-1~I-3
J1-1
J2-1~J2-8
A2-1
GENERAL SPECIFICATIONS
G-1
TV
CRT
CRT Size / Visual Size
30 inch / 760mmV
System
CRT Type
Flat (16:9)
Deflection
100
degree
Magnetic Field
BV/BH
+0.45G/0.18G
Color System
NTSC
Speaker
2 Speaker
Position
Front Bottom
Size
1.8 x 3.9 Inch
Impedance
4
ohm
Sound Output
MAX
10W+10W
10%(Typical)
-W
NTSC3.58+4.43 /PAL60Hz
No
G-2
Tuning
Broadcasting System
US
System M
System
Tuner and
System
1Tuner
Receive CH
Destination
USA(W/ CABLE)
Tuning System
F-Synth
Input Impedance
VHF/UHF 75 ohm
2 - 69, 4A, A-5 - A-1,
CH Coverage
A - I, J - W, W+1 - W+84
Intermediate
Picture(FP)
45.75MHz
Frequency
Sound(FS)
41.25MHz
FP-FS
4.50MHz
Preset CH
No
Stereo/Dual TV Sound
Yes
Tuner Sound Muting
Yes
G-3
Power
Power Source
AC
120V AC 60Hz
DC
Power Consumption
at AC
185 W at AC 120 V 60 Hz
Stand by (at AC)
1
W at AC 120 V 60 Hz
Per Year
--
kWh/Year
Protector
Power Fuse
Yes
Safety Circuit
Yes
IC Protector(Micro Fuse)
Yes
G-4
Regulation
Safety
UL/CSA
Radiation
FCC/IC
X-Radiation
DHHS/HWC
G-5
Temperature
Operation
+5oC ~ +40oC
Storage
-20oC ~ +60oC
G-6
Operating Humidity
Less than 80% RH
A3-1
GENERAL SPECIFICATIONS
G-7
On Screen
Menu
Yes
Display
Menu Type
Icon
Picture
Yes
Mode(Picture preference)
Yes
Brightness
Yes
Contrast
Yes
Color
Yes
Tint
Yes
Sharpness
Yes
Color Temperature
Yes
Display Format
Yes
Cable Clear
No
SVM
Yes
Reset
Yes
Audio
Yes
MTS
Yes
Bass
Yes
Treble
Yes
Balance
Yes
Stable Sound
Yes
Speakers On/Off
Yes
Dolby Virtual
No
WOW SRS 3D
Yes
WOW Focus
Yes
WOW Tru Bass
Yes
BBE
No
HDMI1
Yes
HDMI2
No
Reset
Yes
Setup
Yes
Language
Yes
Clock Set
Yes
TV/CABLE
Yes
CH Program
Yes
Add/ Erase
Yes
Closed Caption
Yes
Picture Size
Yes
Picture Scroll
Yes
Cinema Mode
Yes
Aspect
Yes
Image Tilt
Yes
Option
Yes
Timer
Yes
Favorite CH
Yes
CH Label
Yes
VIDEO Label
Yes
Locks
Yes
V-Chip
Yes
Lock
Yes
New Password
Yes
Front Panel Lock
Yes
Control Level
Yes
Volume
Yes
Contrast
Yes
Brightness
Yes
Color
Yes
Tint
Yes
Sharpness
Yes
Bass
Yes
Treble
Yes
Balance
Yes
Image Tilt
Yes
Picture Scroll
Yes
Stereo, SAP, Mono
Yes
Video
Yes
Color Stream(Component)
Yes
HDMI
Yes
Channel(TV/Cable)
Yes
CH Label
Yes
Video Label
Yes
Clock
Yes
Game Timer
Yes
Front Panel Lock
Yes
On Timer
Yes
Sleep Timer
Yes
Reset
Yes
Sound Mute
Yes
V-chip Rating
Yes
NOT AVAILABLE
Yes
Picture Size
Yes
A3-2