PC board shown are viewed from parts side.
The parts with no reference number or no parts number
in the exploded views are not supplied.
As regards the resistors and capacitors, refer to the
circuit diagrams contained in this manual.
Parts marked with this sign are safety critical
components. they must be replaced with identical
ensure exact replacement.
!
components - refer to the appropriate parts list and
2 SPECIFICATIONS
2
4 EXPLODED VIEW AND PARTS LIST
5 PC BOARDS AND PARTS LISTS
6 WIRING DIAGRAM
7 INCLUDED ACCESSORIES
1 SAFETY INFORMATION
3
CD RECEIVER
6
10
16
17
3 ADJUSTMENT AND CHECKS
4
TEAC
FM
88
90
94
98
98
100
104
106
108
MHz
SL-D88
VOLUME
TUNING
MIN
MAX
DOWN
UP
1 SAFETY INFORMATION
2
SL-D88
USE OF CONTROLS OR ADJUSTMENT OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
HAZARDOUS RADIATION EXPOSURE.
RESULT IN
SAFETY INFORMATION
This product has been designed and manufactured according to FDA regulations " title 21, CFR, chapter 1,subchapter J,based on
The Radiation Control for Health and Safety Act of 1968" and is classified as class 1 laser product. There is not hazardous
invisible laser radiation during operation because invisible laser radiation emitted inside of this product is completely confined
in the protective housings. The label required in this regulation is shown
.
1
CAUTION
DO NOT REMOVE THE PROTECTIVE HOUSING USING SCREWDRIVER.
IF THIS PRODUCT DEVELOPS TROUBLE, MAKE A CONTACT WITH OUR SERICEMAN, AND DO NOT USE THE PRODUCT A TROUBLED
STATE.
1
FOR U.S.A.
Optical pickup:
Type :
SF-P101N
Laser output : Less than 0.5 mW on the objective lens
Wavelength : 765 - 815 nm
Manufacturer : SANYO Electric Co., Ltd.
CERTIFICATION
THIS PRODUCT COMPLIES WITH DHHS
RULES 21 CFR SUBCHAPTER J APPLI-
CABLE AT DATE OF MANUFACTURE.
TEAC CORPORATION
3-7-3, NAKA-CHO, MUSASHINO-SHI, TOKYO, JAPAN
MANUFACTURED :
SERIAL NO. LABEL
MODEL NO . SL-D88
CD RADIO WITH REMOTE CONTROL
TEAC CORPORATION
25W
120V
60Hz
MADE IN CHINA
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH
CANADIAN ICES-003.
CET APPAREIL NUMERIQUE DE LA CLASS B.
EST CONFORM A LA NORME NMB-003 DU CANADA.
THIS DEVICE COMPLIES WITH PART 15 OF THE
FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS:(1) THIS DEVICE
MAY NOT CAUSE HARMFUL INTERFERENCE,AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFER-
ENCE RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.
!
CAUTION
DO NOT OPEN
NE PAS OUVRIR.
AVIS
RISK OF ELECTRIC SHOCK
: RISQUE DE CHOC ELECTRIQUE
FM ANT
R
L
2 SPECIFICATIONS
SL-D88
3
TUNER Section
Frequency Range (FM):
87.5MHz to 108.00 Mhz
Power Requirements:
120V AC,60Hz
CD PLAYER Section
Frequency Response:
20 Hz to 20 kHz (+/- 1dB)
Wow and Flutter:
Unmeasurable
SPEAKER SYSTEM Section
Type:
65 mm x 2
Impedance:
4 ohms
GENERAL
Design and specifications are subject to change without notice.
Illustrations may differ slightly from production models.
Dimension (W x H x D ):
Weight:
Standard Accessories:
Warranty Card x 1
361 x 129 x 251 mm
3.6 kg
Power Consumption:
3 W + 3 W
Owner s Manual x 1
,
Total Output Power :
Frequency Range (AM):
520kHz to 1710 kHz
25 W
SL-D88
4
3 ADJUSTMENTS AND CHECKS
Use a screwdriver with a plastic or ceramic grip for all adjustment.
3-1 TUNER SECTION
1. Set the function switch to the AM position.
2. Connect the test loop antenna across the output of the signal generator.
3. Connect the oscilloscope to the speaker terminal.
4. Set the signal generator as listed in the alignment chart.
3-1-2 AM adjustment
1. Set the function switch to the FM position.
2. Connect the signal generator output through a 75 ohm dummy
3. Connect the oscilloscope to the speaker terminal.
4. Set the signal generator as listed in the alignment chart.
3-1-1 FM adjustment
antenna to "ANT" on MAIN PCB.
3-2 Adjustment and Test Points
MAIN PCB
L9
L8
PVC1
L7
T5
A
M
A
N
T
C
O
IL
CT002
CT001
CT004
CT003
5
ITEM
ADJUSTMENT POINT
ADJUSTMENT
SG SETTING
TUNER SETTING
2. Tracking
3. Tracking
108MHz
106MHz
106MHz
Repeat step 2
90MHz
90MHz
108MHz
87.5MHz
87.5MHz
1kHz, +/-22.5kHz dev.
1kHz, +/-22.5kHz dev.
1kHz, +/-22.5kHz dev.
1kHz, +/-22.5kHz dev.
L9
L8
PVC CT002
PVC CT001
Adjust for max.output.
Adjust for max. output
and best waveform.
1. IF adjustment
2. AM band
455 kHz
1710kHz
1710kHz
1710kHz
Repeat step 3
600kHz
600kHz
1400kHz
1400kHz
520kHz
520kHz
1kHz, 30% mod
1kHz, 30% mod
1kHz, 30% mod
1kHz, 30% mod
1kHz, 30% mod
L7
AM ANT COIL
PVC CT003
PVC CT004
T5
AM
Adjust for max.output.
Adjust for max. output.
Adjust for max. output
and best waveform.
3-2-1 FM/AM alignment chart
1. FM band
SL-D88
FM
3-2-2 CD alignment
Auto alignment.