Ver 1.2 2000. 03
With SUPPLEMENT 1 (9-923-312-81)
WM-EX655/EX668
AEP Model
UK Model
WM-EX668
Tourist Model
WM-EX655
CASSETTE PLAYER
SPECIFICATIONS
MICROFILM
SERVICE MANUAL
Model Name Using Similar Machanism
NEW
Tape Transport Mechanism Type
MT-WMEX655-125
Dolby noise reduction manufactured under license from
Dolby Laboratories Licensing Corporation.
"DOLBY" and the double-D symbol
a are trademarks of
Dolby Laboratories Licensing Corporation.
Tape Player section and general
Frequency response (
a NR switch off)
30 18,000Hz
Output
Headphones (2 REMOTE jack)
Load impedance 8 300ohms
Power output
4mW + 4mW at DC operation
Power requirements
1.5V DC
Rechargeable battery (NC-6WM), 1.2V, 600mAH, Ni-Cd) One R6
(size AA) battery
Battery life (Aprrox. hours)
Rechargeable NC-6WM
9
Fully charged
Sony R6P (SR)
9
Sony alkaline LR6 (WM)
36
Rechargeable NC-6WM
45
Sony alkaline LR6 (WM)
Used together
Dimensions
Approx. 108.9 x 80 x 21.3 mm (w/h/d)
Weight
Approx. 150g (Main unit)
Approx. 215g (incl. Headphones with remote control, Recharge-
able battery NC-6WM (S), Type (C-60-HF))
Supplied Accessories
· Battery charger (1)
· Rechargeable battery (NC-6WM, 1.2V 600mAh, Ni-Cd) (1)
· Battery case (1) (WM-EX655)
· Stereo earphones with remote control (1) (WM-EX655)
· Carrying pouch (1)
· Rechargeable battery carrying case (1)
· Remote control unit (RM-WME654) (1)
· Sony battery R6P (SR) (1) (WM-EX655)
· AC plug adaptor (1) (WM-EX655)
· Clip (1) (WM-EX655)
Design and specifications are subject to change without notice.
Photo : WM-EX655
2
Specifications ......................................................................... 1
1. GENERAL
Location and Function of Controls ......................................... 3
2. SERVICE NOTE ........................................................ 4
3. DISASSEMBLY
3-1. Case Assy Removal ......................................................... 6
3-2. Audio Board Removal ..................................................... 6
3-3. Cassette lid Assy Removal .............................................. 7
3-4. Mechanism Deck Removal ............................................. 7
4. ADJUSTMENTS
4-1. Mechanical Adjustments ................................................. 8
4-2. Electrical Adjustments .................................................... 8
5. DIAGRAMS
5-1. Explanation of IC Terminals ........................................... 9
5-2. Printed Wiring Boards ................................................... 12
5-3. Schematic Diagram ....................................................... 15
6. EXPLODED VIEWS
6-1. Case Section .................................................................. 20
6-2. Audio Board Section ..................................................... 21
6-3. Mechanism Deck Section (MT-WMEX655-125) ......... 22
7. ELECTRICAL PARTS LIST .................................. 23
TABLE OF CONTENTS
Flexible Circuit Board Repairing
· Keep the temperature of the soldering iron around 270°C during
repairing.
· Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
· Be careful not to apply force on the conductor when soldering or
unsoldering.
Notes on chip component replacement
· Never reuse a disconnected chip component.
· Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
3
SECTION 1
GENERAL
LOCATION AND FUNCTION OF CONTROLS
Tape player section and general
r
Main unit
r
Headphones with Remote Control
This section is extracted from
instruction manual.
1 OPEN knob
2 Contact for dry battery case
3 Tape operation buttons
4 Rechargeable battery case
5 BL SKIP indicatior
6 AVLS indicatior
7 FUNCTION button
8 HOLD switch
9 MB/GRV (Mega Bass/Groove) indicator
0 Main unit : VOLUME knob
Remote control : VOL knob
!¡ BATT indicator
!TM 2 REMOTE jack
!£ a (DOLBY) NR indicator
!¢ SOUND/AVLS (Auto Volume limitter
system) switch
! Micro plug
WM-EX655
!
3
3
8
!º
!¢
8
!º
Left
Right
Left
Right
WM-EX668
4
SECTION 2
SERVICE NOTE
SERVICE MODE
Mode which enables the mechanism to be operated with the AU-
DIO board opened.
This set detects the rotation of GEAR (S) using the PH701 (photo
reflector). The PH701 is mounted on the AUDIO board, and there-
fore the GEAR cannot be detected with the AUDIO board removed.
As a result, the motor cannot be controlled, causing malfunction.
Further, the S702 (FWD/REV switch) is also mounted on the AU-
DIO board, and with the board removed, the mechanism position
cannot be detected and the operation is not changed over.
Therefore, when the voltage check is executed with the AUDIO
board removed, follow the procedure provided below.
Note : Do not move the S702 switch position when removing the
AUDIO board.
If it is moved, the set will not be changed over to the se-
lected mode. In this case, reconnect the AUDIO board to
the set and retry the work from the beginning.
1. Setting
1) Refer to "3. DISASSEMBLY", and remove the case and open
the AUDIO board.
2) Connect the AUDIO board to the M901 (motor) and PM901
(plunger) using a jumper wire. (See Fig- 2)
3) Short the ATS terminals (S901).
4) Press and fixed the S701 (HOLDER SW). (See Fig- 1)
[AUDIO board ] (Side B)
(Fig - 1)
5) Supply 1.5V to the battery terminals
`and 'using a stabilized
power supply.
2. FF, REW Modes
1) Input a square wave to the TP35 (PHOTO IN). (See Fig-3)
2) Press the S704 (STOP) for selecting STOP mode.
3) Press the S706 (FF) or S707 (REW).
Tape
S701
(HOLDER SW)
3. PLAY Mode
1) Input a square wave to the TP35 (PHOTO IN). (See Fig-3)
2) Press the S704 (STOP) for selecting STOP mode.
3) Press the S705 (PLAY). (Each time the switch is pressed, the
mode is chaged over.)
[AUDIO board ] (Side A)
(Fig - 2)
[AUDIO board ] (Side B)
(Fig - 3)
IC701
S704
(
p)
S705
(
9()
S706
(FF)
S707
(REW )
S708
(FUNCTION)
IC301
battery terminal
'
battery terminal
`
connect to plunger (PM901)
ATS terminals
(S901)
connect to
motor (M901)
TP35
S702
(F/R SW)
S701
(HOLDER SW)
F side
R side
Center
audio frequency
generator
square wave signal
10Hz, 3.5dB
5
LEVER (SW )
Rortation system during FF.
Rortation system during REW.
Rortation system during PLAY.
side R
lever (SW)
side F
center
Gear (FR)
(FF : Left side)
Gear (Y)
Gear (NR)
Motor pully
Clutch Assy (M)
Gear (Reel)
(T side)
Gear (TB)
Flywheel (N) Assy
Flywheel (R) Assy
Pully (Reverse)
Gear (Reel)
(T side)
Gear (Reel)
(S side)
Gear (TA)
Gear (TB)
Gear (S)
Gear (Y)
Gear (NR)
(REV : Left side/
FWD : Right side)
Motor Pully
Flywheel (N) Assy
Flywheel (R) Assy
Pully (Reverse)
Clutch
Assy (M)
Gear (Reel)
(S side)
Gear (FR)
(REW : Right side)
Gear (S)
Gear (Y)
Gear (NR)
Motor Pully
Clutch Assy (M)
Flywheel (N) Assy
Flywheel (R) Assy
Pully (Reverse)