1
GB
© 2000 Sony Corporation
4-230-316-
12(1)
Home Theater
System
HT-K170
GB
FR
NL
SE
Operating instructions
Mode d'emploi
Gebruiksaanwijzing
Bruksanvisning
Getting Started
2
GB
WARNING
To prevent fire or shock
hazard, do not expose
the unit to rain or
moisture.
To avoid electrical shock, do not open
the cabinet. Refer servicing to qualified
personnel only.
Precautions
On safety
· Should any solid object or liquid fall
into the cabinet, unplug the amplifier
and have it checked by qualified
personnel before operating it any
further.
On power sources
· Before operating the amplifier, check
that the operating voltage is identical
with your local power supply. The
operating voltage is indicated on the
nameplate at the rear of the amplifier.
· The amplifier is not disconnected
from the AC power source (mains) as
long as it is connected to the wall
outlet, even if the amplifier itself has
been turned off.
· If you are not going to use the
amplifier for a long time, be sure to
disconnect the amplifier from the
wall outlet. To disconnect the mains
lead, grasp the plug itself; never pull
the cord.
· The AC power cord (mains lead)
must be changed, at a qualified
service shop only.
· The mains switch is located on the
front exterior.
On placement
· Do not install the appliance in a
confined space, such as a bookcase or
built in cabinet.
· Place the amplifier in a location with
adequate ventilation to prevent heat
buildup and prolong the life of the
amplifier.
· Do not place the amplifier near heat
sources, or in a place subject to direct
sunlight, excessive dust or
mechanical shock.
· Do not place anything on top of the
cabinet that might block the
ventilation holes and cause
malfunctions.
· Do not set the speakers in an inclined
position.
· Do not place the speakers in locations
that are:
Extremely hot or cold
Dusty or dirty
Very humid
Subject to vibrations
Subject to direct sunlight
On operation
· Before connecting other components,
be sure to turn off and unplug the
amplifier.
· Do not drive the speaker system with
a continuous wattage exceeding the
maximum input power of the system.
· If the polarity of the speaker
connections are not correct, the bass
tones will be weak and the position of
the various instruments obscure.
· Contact between bare speaker wires
at the speaker terminals may result in
a short-circuit.
· The speaker grille cannot be removed.
Do not attempt to remove the grille
on the speaker system. If you try to
remove it, you may damage the
speaker.
If you encounter color irregularity on
a nearby TV screen
This speaker system is magnetically
shielded to allow it to be installed near a
TV set. However, color irregularities
may still be observed on certain types of
TV sets.
If color irregularity is observed...
p Turn off the TV set once, then turn
it on again after 15 to 30 minutes.
If color irregularity is observed
again...
p Place the speakers further away
from the TV set.
If howling occurs
Reposition the speakers or turn down
the volume on the amplifier.
On cleaning
· Clean the cabinet, panel and controls
with a soft cloth slightly moistened
with a mild detergent solution. Do
not use any type of abrasive pad,
scouring powder or solvent such as
alcohol or benzine.
If you have any question or problem
concerning your amplifier, please
consult your nearest Sony dealer.
Getting Started
3
GB
About This Manual
Conventions
· The instructions in this manual
describe the controls on the amplifier
and speakers. You can also use the
controls on the remote if they have
the same or similar names as those on
the amplifier.
· The following icons are used in this
manual:
Indicates that you can use only
the remote to do the task.
Indicates hints and tips for
making the task easier.
This amplifier contains a Dolby Pro
Logic Surround decoder.
Manufactured under license from Dolby
Laboratories.
"Dolby", "AC-3", "Pro Logic" and the
double-D symbol ; are trademarks of
Dolby Laboratories.
Hold down ?/1 and press CENTER
MODE to change the fan control
setup. Each time you do the
procedure above, the following setup
appears.
Select
To
FAN ON
Turn on the fan at all
times.
FAN AUTO Turn on the fan
automatically when
there is sufficient
speaker output.
TABLE OF CONTENTS
Getting Started
Unpacking 4
Hookup Overview 4
Video Component Hookups 5
Speaker System Hookups and Setups 6
AC Hookups 9
Before You Use Your Amplifier 10
Amplifier Operations
Selecting a Component 11
Changing the Factory Setting of a FUNCTION Button 13
Using the Sleep Timer 14
Using Surround Sound
Choosing a Sound Field 15
Getting the Most Out of Dolby Pro Logic Surround Sound 16
Additional Information
Troubleshooting 18
Specifications 19
Glossary 20
Remote Button Description 21
Index 22
Rear Panel Descriptions 22
Getting Started
4
GB
Getting Started
Unpacking
Check that you received the following items with your
amplifier:
· Remote commander (remote) (1)
· Size AA (R6) batteries (2)
· Scart adaptor (1)
· Speakers (5)
· Front speakers (2)
· Rear speakers (2)
· Center speaker (1)
· Subwoofer (1)
· Speaker connecting cord, 10 m (2)
· Speaker connecting cord, 2.5 m (3)
· Monaural connecting cord (1 phono to 1 phono) (1)
· Foot pads (20)
Inserting batteries into the remote
Insert two size AA (R6) batteries with the + and on
the battery compartment. When using the remote,
point it at the remote sensor g on the amplifier.
When to replace batteries
Under normal use, the batteries should last for about 6
months. When the remote no longer operates the
amplifier, replace both batteries with new ones.
Notes
· Do not leave the remote in an extremely hot or humid
place.
· Do not use a new battery with an old one.
· Do not expose the remote sensor to direct sunlight or
lighting apparatuses. Doing so may cause a malfunction.
· If you don't use the remote for an extended period of time,
remove the batteries to avoid possible damage from
battery leakage and corrosion.
]
]
}
}
Hookup Overview
The amplifier allows you to connect and control the
following video components. Follow the hookup
procedures for the components that you want to
connect to the amplifier on the pages specified. To
learn the locations and names of each jack, see "Rear
Panel Descriptions" on page 22.
Before you get started
· Turn off the power to all components before making
any connections.
· Do not connect the mains lead until all of the
connections are completed.
· Be sure to make connections firmly to avoid hum
and noise.
· When connecting an audio cable, be sure to match
the colour-coded pins to the appropriate jacks on the
components: White (left, audio) to White; and Red
(right, audio) to Red.
Rear
speaker
(L)
Rear
speaker
(R)
Front
speaker
(L)
Front
speaker
(R)
TV
Video Component
Hookups (5)
VCR
Speaker System
Hookups (6)
DVD
player/
AC-3
decoder
Active
subwoofer
Center
speaker
Getting Started
5
GB
Video Component Hookups
Overview
This section describes how to connect video
components to the amplifier. For specific locations of
the jacks, see the illustration below.
What cords will I need?
· Scart adaptor (supplied)
· Euro AV cable (not supplied) (1 for each TV or VCR)
· Audio cords (not supplied) (1 for DVD player, 2 for AC-3
decoder's FRONT and REAR jacks)
· Monaural audio cords (not supplied)
(2 for AC-3 decoder's CENTER and WOOFER jacks)
5.1CH/DVD
TV
DVD 2CH
VIDEO
VTR
TV
L
R
L
R
To VTR audio input
Amplifier
VIDEO AUDIO IN
ç
Euro AV cable (not
supplied)
Scart adaptor
(supplied)
To TV
n
TV
White
(L)
White
(L)
Red
(R)
Red
(R)
ç
To TV audio input
Hookups
The arrow
l indicates signal flow.
TV/VCR
You can listen to the sound from VCR or TV by
connecting the audio signal from VCR or TV to the
amplifier.
If you have another component, such as a second VCR
or LD player, connect it to the DVD 2CH jacks.
DVD Player
If your DVD player does not have 5.1 CH output,
connect the audio output jacks of the DVD player to the
DVD 2CH jacks of the amplifier.
AUDIO IN
AUDIO OUT
DVD 2CH
LL
R
R
L
Amplifier
DVD 2CH
DVD player
AUDIO OUT
(continued)
Red (R)
Red (R)
White (L)
White (L)
Black
Black