Inputs
S/N (weighting
Sensitivity
Impedance
network, input
level)
75 dB*
PHONO
2.5mV
50 kilohms
(A, 2.5mV)
82 dB*
TUNER
150mV
50 kilohms
(A, 150mV)
82 dB*
CD
200mV
50 kilohms
(A, 200mV)
TAPE/MD,VIDEO1, 2, 3
150mV
50 kilohms
82 dB*
TV/LD (AEP, UK model)
150mV
(A, 150mV)
TV/LD
82 dB*
(EXCEPT AEP, UK model)
250mV
50 kilohms
(A, 250mV)
82 dB*
5.1 INPUT
200mV
50 kilohms
(A, 200mV)
* '78 IHF
Outputs
VIDEO 1, 2, 3, AUDIO OUT :
Voltage : 150 mV, Impedance : 10 kilohms
WOOFER :
Voltage : 2 V
Impedance : 1 kilohms
PHONES :
Accepts low and high impedance headphones
BASS BOOST
+10 dB at 70 Hz
TONE
± 8 dB at 100Hz and 10 kHz
MICROFILM
Manufactured under license from Dolby Laboratories Licensing
Corporation.
"Dolby", the double-D symbol
a and "Pro Logic" are trademarks
of Dolby Laboratories Licensing Corporation.
INTEGRATED AV AMPLIFIER
Photo : TA-VE610
AEP Model
UK Model
E Model
TA-VE610
Chinese Model
TA-V606
SERVICE MANUAL
TA-V606/VE610
SPECIFICATIONS
Amplifier section
POWER OUTPUT
Stereo mode
V606 : (6 ohms 1kHz, THD 0.7 %)
110 W + 110W
VE610 : (4 ohms 1kHz, THD 0.7 %)
100 W + 100W
Surround mode
V606 : (6 ohms at 1kHz, THD 0.7 %)
Front : 110 W/ch
Center* : 110 W
Rear* : 110 W/ch
VE610 : (4 ohms at 1kHz, THD 0.7 %)
Front : 100 W/ch
Center* : 100 W
Rear* : 100 W/ch
*Depending on the sound field settings and the
source, sound will not be output.
5.1 mode
V606 : (6 ohms at 1kHz, THD 0.7 %)
Front : 110 W/ch
Center : 110 W
Rear : 110 W/ch
VE610 : (4 ohms at 1kHz, THD 0.7 %)
Front : 100 W/ch
Center : 100 W
Rear : 100 W/ch
Harmonic distortion at rated output
Less than 0.09% (with DIRECT PASS on)
Frequency respones
PHONO : RIAA equalization curve
± 0.5dB
CD, TAPE, DAT/MD, VIDEO 1, 2 :
+0
10Hz 50 kHz 1 dB (with DIRECT PASS on)
Continued on page 2
2
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
! OR DOTTED LINEWITH
MARK
! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
TABLE OF CONTENTS
Specifications ........................................................................... 1
1.
GENERAL
Location and Function of Controls .................................... 3
2.
DIAGRAMS
2-1. IC Pin Function ........................................................... 5
2-2. Circuit Boards Locations ............................................ 7
2-3. Printed Wiring Boards Surround Section ............. 8
2-4. Schematic Diagram Surround Section ............... 11
2-5. Schematic Diagram AMP Section ..................... 15
2-6. Printed Wiring Boards AMP Section .................. 19
2-7. Printed Wiring Boards Display Section ............. 23
2-8. Schematic Diagram Display Section .................. 27
3.
EXPLODED VIEWS
3-1. Front Panel Section ................................................... 32
3-2. Chassis Section ......................................................... 33
3-3. Back Panel Section ................................................... 34
4.
ELECTRICAL PARTS LIST ........................................ 35
Video section
Inputs
1 Vp-p 75 ohms
Outputs
1 Vp-p 75 ohms
General
System
Preamplifier section :
Low-noise NF type equalizer
Power amplifier section :
Pure-complementary SEPP
Power requirements
AEP, Singapore, Malaysia model :
230 V AC, 50/60Hz
UK model : 240 V AC, 50/60Hz
Chinese model : 220 V AC, 50/60Hz
Power consumption
240W
AC outlets
EXCEPT Chinese model :
1 switched, maximum 100W
Chinese model : 2 switched, total 100 W
Dimensions
430 x 155 x 350 mm
including projecting parts and controls
Mass (Approx.)
9.8 kg
Supplied accessories
Remote commander (remote) RM-U501 (1)
Size AA (R6) batteries (2)
Design and specifications are subject to change without notice.
3
SECTION 1
GENERAL
LOCATION AND FUNCTION OF CONTROLS
This section is extracted from
instruction manual.
[FRONT PANEL]
!TM SOUND FIELD ON/OFF button
!£ MODE button
!¢ GENRE button
! DIRECT PASS, SET UP, 5.1/DVD INPUT buttons
!§ AUDIO FUNCTION buttons
!¶ VIDEO FUNCTION buttons
!· DISPLAY button
!ª DIMMER button
@º PHONES jack
@¡ SPEAKERS switch
1 DPC MODE button
2 POWER switch
3 SUR, TONE, INDEX indicators
4 Digital processing control buttons
5 Function indicators
6 DIRECT PASS indicator
7 5.1 INPUT indicator
8 MASTER VOLUME control
9 BALANCE control
!º VIDEO 3 INPUT jacks
!¡ BASS BOOST button/indicator
1
8
5
3
2
!TM
!¶
!§
!£
!¢
!
!·
!ª
@º
@¡
!º
9
67
4
!¡
4
!¡ MASTER VOL +/
!TM MUTING
!£ DPC MODE
!¢ DIGITAL PROCESSING CONTROL
! DIRECT
!§ EQ/TONE
!¶ SOUND FIELD ON/OFF/GENRE/MODE
!· BACKGROUND
!ª Numeric buttons
@º TV CONTROL ON
1 SLEEP
2 SYSTEM OFF
3 SYSTEM CONTROL/FUNCTION
4 5.1 INPUT
5 TV/VIDEO
6 ENTER
7 TEST TONE
8 CENTER LEVEL +/
9 REAR LEVEL +/
!º BASS BOOST
[REMOTE]
[REAR PANEL]
1 5.1 INPUT
2 TV/LD
3 VIDEO 2
4 VIDEO 1
5 MONITOR
6 WOOFER
7 SURROUND SPEAKERS (REAR)
8 SURROUND SPEAKERS (CENTER)
9 WIRELESS REAR SPEAKER
!º AC OUTLET
(Outlet shape and position varies
according to destination)
!¡ AC power cord
!TM FRONT SPEAKERS (A/B)
!£ TAPE/MD
!¢ CD
! TUNER
!§ PHONO
!¶ y SIGNAL GND
5
IC103 µPD780205GF-032-3BA (SYSTEM CONTROL)
Pin No.
Pin name
I/O
Description
1
Not used (Connect to VDD).
2 to 4
Not used (Connect to ground).
5
F/C/W. MUTE
O
Front, Center, Woofer mute drive.
6
SL MUTE
O
Surround L-CH mute drive.
7
SR MUTE
O
Surround R-CH mute drive.
8
AC MUTE
O
AC mute drive.
9
D LATCH
O
Data latch output.
10
RESET
I
Reset terminal.
11
X2
O
System clock (4.19MHZ).
12
X1
I
System clock (4.19MHZ).
13
VSS
Ground.
14
NP
Not used (Open).
15
Connect to reset terminal.
16
VDD
Power supply (+5V).
17
T LATCH
O
Tuner function latch output.
18
S CLOCK
O
Serial clock output.
19
S DATA
O
Serial data output.
20
S LATCH
O
Serial latch output.
21
AUTO STOP
Not used (Connect to ground).
22
V MUTE
O
Video mute output.
23
STEREO
Not used (Connect to ground).
24
IF DATA IN
Not used (Open).
25
GND A/D
Ground for A/D converter.
26
SIRCS
I
Remote control signal input.
27
POWER KEY
I
Power key input.
28
VERSION
I
Destination select input.
29
KEY 5
I
Key input.
30
KEY 4
I
Key input.
31
KEY 3
I
Key input.
32
KEY 2
I
Key input.
33
KEY 1
I
Key input.
34
VDD A/D
Power supply (+5V) for A/D converter.
35
VREF A/D
I
Reference voltage for A/D converter.
36
V-A
O
Video switch control output.
37
V-B
O
Video switch control output.
38
V-E
O
Video switch control output.
39
STOP
O
Power ON/OFF control output.
40
VSS
Ground.
41
DIRECT PASS
O
Direct pass relay drive.
42
SUR RY
O
Surround relay drive.
43
CENTER RY
O
Center relay drive.
44
FRONT RY
O
Front relay drive.
45
MIX SUB RY
O
Woofer relay drive.
SECTION 2
DIAGRAMS
2-1. IC PIN FUNCTION