MICROFILM
SERVICE MANUAL
5 CHANNEL POWER AMPLIFIER
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Chinese Model
TA-N9000ES
SPECIFICATIONS
Photo: GOLD model
2
TABLE OF CONTENTS
1.
SERVICING NOTES ............................................... 3
2.
GENERAL ................................................................... 4
3.
DISASSEMBLY ......................................................... 5
4.
ELECTRICAL ADJUSTMENTS ......................... 7
5.
DIAGRAMS ................................................................. 8
5-1. Note for Printed Wiring Boards and
Schematic Diagrams .......................................................
9
5-2. Printed Wiring Boards MAIN Section .................... 11
5-3. Schematic Diagram MAIN Section (1/3) ................ 13
5-4. Schematic Diagram MAIN Section (2/3) ................ 15
5-5. Schematic Diagram MAIN Section (3/3) ................ 17
5-6. Printed Wiring Boards CONTROL Section ............ 19
5-7. Schematic Diagram CONTROL Section ................. 21
5-8. Printed Wiring Boards POWER Section ................. 23
5-9. Schematic Diagram POWER Section ..................... 25
5-10. IC Pin Function Description ........................................... 27
6.
EXPLODED VIEWS ................................................ 28
7.
ELECTRICAL PARTS LIST ............................... 30
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
!
SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE
DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ
DE FONCTIONNEMENT. NE REMPLACER CES COM-
POSANTS QUE PAR DES PIÈCES SONY DONT LES
NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
! OR DOTTED
LINE WITH MARK
! ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
3
SECTION 1
SERVICING NOTES
MODEL IDENTIFICATION
Rear view
12345678
12345678
12345678
PART No.
MODEL
PART No.
US, Canadian models
4-211-114-1
Except US, Canadian models
4-211-114-2
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, "metallized" knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers' instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The "limit" indica-
tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-
amples of a passive VOM that is suitable. Nearly all battery
operated digital multimeters that have a 2 V AC range are suit-
able. (See Fig. A)
Fig. A.
Using an AC voltmeter to check AC leakage.
1.5 k
0.15
µF
AC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
Notes on chip component replacement
· Never reuse a disconnected chip component.
· Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
4
SECTION 2
GENERAL
This section is extracted from
instruction manual.
5
CASE
FRONT PANEL SECTION
Note: Follow the disassembly procedure in the numerical order given.
SECTION 3
DISASSEMBLY
1 two screws
(BV3 x 8B)
2 two flat head screws
2 two flat head screws
3 case
4
4
4
5 front panel section
3 three screws
(BV3
× 8B)
2 four connectors
(CN152, 153, 154, 155)
1 Unlock each claw of the saddle wire.