ST-JX661/SE200
FM STREO/FM-AM TUNER
US Model
Canadian Model
ST-JX661
AEP Model
UK Model
E Model
Australian Model
ST-JX661/SE200
Chinese Model
ST-SE200
SERVICE MANUAL
MICROFILM
SPECIFICATIONS
Photo : ST-JX661
FM tuner section
Frequency range
87.5108 MHz
Antenna terminals
75 ohms, unbalanced
Intermediate frequency
10.7 MHz
Sensitivity
at 50 dB quieting (mono) 22.1 dBf, 7
µV/75
(stereo) 42.1dBf, 7
µV/75
Usable sensitivity (IHF)
19.5 dBf, 5
µV/75
at 75 kHz deviation
S/N
80 dB (mono), 75 dB (stereo)
Harmonic distortion
at 1 kHz
0.3% (mono), 0.5% (stereo)
Frequency response
30 Hz15 kHz
(+0.5/2.0 dB)
Separation
35 dB at 1 kHz
Selectivity
55 dB at 400 kHz
Output
at 75 kHz deviation
775 mV, 4.7 kilohms
AM tuner section
Frequency range
US, Canadian model :
5311,710 kHz (9 kHz)
5301,710 kHz (10 kHz)
AEP, UK, German, Italian model :
5221,611 kHz (9 kHz)
E, Singapore, Australian, Chinese, Malaysia,
Saudi Arabia model :
5311,602 kHz (9 kHz)
5301,710k Hz (10 kHz)
Intermediate frequency
450 kHz
Usable sensitivity
(with AM loop antenna) AM : 500
µV/m
Signal-to-noise ratio
54 dB (500mV/m, 999 kHz)
Harmonic distortion
0.5 % (50 mV/m, 400Hz)
Selectivity
50 dB
General
Power requirements
US, Canadian model :
120 V AC, 60 Hz
AEP, German, Italian model :
220-230 V AC, 50/60Hz
UK, Australian model :
240 V AC, 50/60Hz
E, Singapore, Chinese, Malaysia,
Saudi Arabia model :
110-120 V/220-240 V AC,
50/60 Hz adjustable
Power consumption
7 W
Dimensions
430 x 82 x 279 mm (w/h/d) (17 x
31/
4 x 11 inches)
Mass
Approx. 2.4 kg (5 lb 4 oz)
Supplied accessorise
Audio cord (1)
AM loop antenna (1)
FM wire antenna (1)
Design and specifications are subject to change without notice.
2
TABLE OF CONTENTS
Section
Title
Page
Specifications ................................................................................ 1
1. GENERAL
Location of Controls ............................................................... 3
2. ADJUSTMENTS ............................................................... 4
3. EXPLANATION OF IC TERMINALS .......................... 5
4. DIAGRAMS
4-1. Circuit Boards Location ................................................... 7
4-2. Printed Wiring Boards ...................................................... 8
4-3. Schematic Diagram ........................................................ 11
5. EXPLODED VIEW
5-1. Front Section .................................................................. 15
6. ELECTRICAL PARTS LIST ........................................ 17
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer :
Check the antenna terminals, metal trim, "metallized" knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a re-
turn to chassis, must not exceed 0.5mA (500 microampers).
Leakage current can be measured by any one of three methods.
1.
A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers' instructions to use these
instruments.
2.
A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The "limit" indication is 0.75V,
so analog meters must have an accurate low-voltage scale. The
Simpson 250 and Sanwa SH-63Trd are examples of a passive
VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
AC
Voltmeter
(0.75V)
0.15 F
µ
1.5k
To Exposed Metal
Parts on Set
MODEL NO.
ST-JX661
ST-SE200
FM STEREO/FM-AM TUNER
MODEL IDENTIFICATION
Model Number Label
US, Canadian model : AC 120
/60Hz
UK, Australian model : AC 240
/50Hz
AEP, German, Italian model : AC 220230V
/50Hz
E, Singapore, Chinese,
Malaysia, Saudi Arabia model : AC 110120 V/220240 V
/50/60 Hz
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
! SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
! OR DOTTED LINE WITH
MARK
! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
3
SECTION 1
GENERAL
12 3
45
6
7
8
1 POWER button
2 MEMORY SCAN button
3 STEREO/MONO button
5 Numeric buttons
6 TUNING buttons
7 MEMORY button
4 Display window
8 BAND button
LOCATION OF CONTROLS
4
TUNER SECTION
Note 1 : The adjustment should be performed in the publication.
(AM
n FM)
Note 2 : As a front-end (FE1) is difficult to repair if faulty, replace
it with new one.
AM Section Adjustment
Setting :
set
loop antenna A
loop antenna B
60cm
AM RF signal
generator
Carrier frequency : 1,050kHz (US, Canadian)
999kHz (EXCEPT US, Canadian)
Modulation : 400Hz, 30% modulation
FM Section Adjustment
Setting :
set
FM ANTENNA terminal (TM1)
75
coaxial
FM RF signal
generator
Carrier frequency : 98MHz
Modulation : 1kHz, 75kHz deviation
AM Tuned Indication Lighting Level Adjustment
Band : AM
Procedure :
1. Set loop antenna A so that the loop antenna B input level becomes
316.2
µV (50dBµ)
2. Tune the set to 1,050kHz (US, Canadian) or 999kHz (EXCEPT
US, Canadian).
3. Adjust RV41 so that the TUNED light up.
4. Confirm that the TUNED light off with AM RF signal generator
output level set at 251.2
µV (48dBµ)
5. Confirm the FM tuned indication lighting level and adjust if nec-
essary.
Adjustment Location : TUNER board
SECTION 2
ADJUSTMENTS
FM Tuned Indication Lighting Level Adjustment
Band : FM
Procedure :
1. Supply a 31.6
µV (30dBµ) 98 MHz signal to the ANTENNA ter-
minal (TM1).
2. Tune the set to 98MHz.
3. Adjust RV42 so that the TUNED light up.
4. Confirm that the TUNED light off with FM RF signal generator
output level set at 25.1
µV (28dBµ).
Adjustment Location : TUNER board
RV41 : AM Tuned Level
RV42 : FM Tuned Level
[ TUNER BOARD ] Component side
5
SECTION 3
EXPLANATION OF IC TERMINAL
IC701 µPD78042AGF-078-3B9 (FL DRIVER)
Pin No.
Pin name
I/O
Description
1G7
O
2G6
O
3G5
O
4
G4
O
FL drive.
5G3
O
6G2
O
7G1
O
8
VDD
Power supply (+5V)
9
PLL CE
O
Chip enable output to PLL IC.
10
PLL DATA OUT
O
PLL data output.
11
PLL CLK
I
PLL clock input.
12
PLL DATA IN
I
PLL data input.
13
AST
I
Tuned signal input.
14
ST
I
Stereo signal input.
15
NC
Not used. (Ground)
16
NC
Not used. (Ground)
17
RESET
I
System reset input.
18
DC CUT
Not used. (Open)
19
NC
Not used. (Open)
20
AVSS (GND)
Ground.
21
MUTE
O
Line mute output.
22
NC
Not used. (Open)
23
NC
Not used. (Open)
24
NC
Not used. (Open)
25
MODEL
Not used. (Ground)
26
KEY 3
I
Key input.
27
KEY 2
I
Key input.
28
KEY 1
I
Key input.
29
AVDD
Power supply (+5V)
30
AVREF
Analog voltage reference.
31
GND
Ground.
32
NC
Not used. (Open)
33
GND
Ground.
34
X1
I
System clock. (5MHz)
35
X2
O
System clock. (5MHz)
36
NC
Not used. (Open)
37
POWER SW
I
Power switch input.
38
NC
Not used. (Ground)
39
NC
Not used. (Ground)
40
NC
Not used. (Ground)