SERVICE MANUAL
Ver 1.1 2003.11
SPEAKER SYSTEM
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
SS-CT7/FL7/FL7RC/RS7
9-873-938-02
Sony Corporation
2003K05-1
Home Audio Company
C
2003.11
Published by Sony Engineering Corporation
SS-FL7
SS-RS7
SS-CT7
SPECIFICATIONS
SS-FL7RC
Center Speaker
SS-CT7
Rear Speaker
SS-RS7
Front Speaker
SS-FL7
COMPONENT MODEL NAME FOR THESE SYSTEM
SS-FL7
Speaker system
2-way, 3-unit, bass-reflex type,
magnetically shielded type
Speaker units
Woofer:
13 cm, cone type
× 2
Tweeter:
5 cm, cone type
Rated impedance
8 ohms
Dimensions (w/h/d)
Approx. 245
× 425 × 320 mm
Mass
Approx. 6.3 kg net per speaker
SS-RS7
Speaker system
2-way, 2-unit, bass-reflex type
Speaker units
Woofer:
8 cm, cone type
Tweeter:
4 cm, cone type
Rated impedance
8 ohms
Dimensions (w/h/d)
Approx. 100
× 250 × 145 mm
Mass
Approx. 1.2 kg net per speaker
SS-CT7
Speaker system
2-way, 2-unit, bass-reflex type,
magnetically shielded type
Speaker units
Woofer:
8 cm, cone type
Tweeter:
5 cm, cone type
Rated impedance
16 ohms
Dimensions (w/h/d)
Approx. 100
× 250 × 145 mm
Mass
Approx. 1.2 kg net per speaker
SS-FL7RC is composed of following models.
Design and specifications are subject to change without notice.
· JIG
When disassembling the set, use the following jig (for
speaker removal).
Part No.: J-2501-238-A JIG FOR SPEAKER REMOVAL
2
SS-CT7/FL7/FL7RC/RS7
SECTION 1
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
DISASSEMBLY OF SS-FL7
Note 1: Remove the front panel assy by paying attention particulaly
to the periphyery of eight bosses
where the front panel assy bonded tightly.
Note 2: Take care not to damage the set
by applying an excessive force.
boss
boss
boss
boss
1
Insert a flat-tip screwdriver into a recess
in the bottom of the set
to raise the front panel assy a little.
2
Insert the jig (J-2051-238-A) into a space
made by inserting the screwdriver,
and raise the front panel assy gradually.
1
Insert a flat-tip screwdriver into a recess
in the bottom of the set
to raise the front panel assy a little.
2
Insert the jig (J-2051-238-A) into a space
made by inserting the screwdriver,
and raise the front panel assy gradually.
Ver 1.1
3
SS-CT7/FL7/FL7RC/RS7
5
Raise the front panel assy a little by little
from bottom to top of the set.
6
front panel assy
Ver 1.1
4
SS-CT7/FL7/FL7RC/RS7
· Items marked "*" are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
· Accessories are given in the last of the elec-
trical parts list.
NOTE:
· -XX and -X mean standardized parts, so they
may have some difference from the original
one.
· Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
Parts Color Cabinet's Color
not
supplied
#1
1
SP1
6
SP2
6
5
4
3
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
1
A-4735-863-A FRAME ASSY, GRILLE
3
4-874-614-31 SCREW (1) (3.5X12), TAPPING
4
4-239-089-01 CABINET
5
1-694-516-21 TERMINAL, SPEAKER
6
4-874-614-71 SCREW
SP1
1-825-083-11 SPEAKER (5cm)
SP2
1-825-084-11 SPEAKER (8cm)
#1
7-685-663-79 SCREW +BVTP4X16 TYPE2 IT-3
2-1. SS-CT7
SECTION 2
EXPLODED VIEWS
5
SS-CT7/FL7/FL7RC/RS7
not
supplied
not
supplied
not supplied
not supplied
not
supplied
55
SP3
56
53
SP4
SP3
57
58
#2
#2
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
53
4-874-614-21 SCREW (1) (3.5X14), TAPPING
55
4-238-407-01 SCREW (1) (4X20), +BV TAPPING
56
4-238-882-01 PANEL, TOP
57
A-4735-799-A PANEL ASSY, FRONT
58
A-4735-801-A FRAME ASSY, GRILLE
SP3
1-825-087-11 SPEAKER (12cm)
SP4
1-825-001-11 SPEAKER (5cm)
#2
7-685-166-01 SCREW +P4X30 TYPE4
2-2. SS-FL7