SONY RM-PP506L - Owner's Manual Immediate Download

Remote

Commander

Operating Instructions

4-241-678-11(1)

RM-PP506L

Owner's Record

The model and serial numbers are located on the rear of the unit. Record the serial

number in the space provided below. Refer to them whenever you call upon your Sony

dealer regarding this product.

Model No.

Serial No.

2GB

Precautions

On safety

Should any solid object or liquid fall into the cabinet,

unplug the receiver and have it checked by qualified

personnel before operating it any further.

On operation

Before connecting other components, be sure to turn

off and unplug the receiver.

On cleaning

Clean the cabinet, panel and controls with a soft cloth

slightly moistened with a mild detergent solution. Do

not use any type of abrasive pad, scouring powder or

solvent such as alcohol or benzine.

If you have any question or problem

concerning your remote, please consult your

nearest Sony dealer.

About this manual

The instructions in this manual are for model

RM-PP506L. Check your model number by

looking at the lower right corner of the front

side.

3GB

Before you use your

remote

Inserting batteries into the

remote

Insert two R6 (size-AA) batteries with the +

and properly oriented in the battery

compartment.

Tip

Under normal conditions, the batteries should last for

about 6 months. When the remote no longer operates

the receiver, replace both batteries with new ones.

Notes

· Do not leave the remote in an extremely hot or

humid place.

· Do not use a new battery with an old one.

· Do not expose the remote sensor of the receiver to

direct sunlight or lighting apparatuses. Doing so

may cause a malfunction.

· If you don't use the remote for an extended period

of time, remove the batteries to avoid possible

damage from battery leakage and corrosion.

Table of Contents

Location of Parts and Basic

Remote Operations

Parts description .................................... 4

Table of buttons that you can use to

control each component .................. 9

Advanced Remote Operations

Programming the remote ..................... 10

Learning the commands of your

components ................................... 13

Performing several commands in

sequence automatically

(Macro Play) .................................. 14

Selecting the mode of the remote ........ 15

Additional Information

Troubleshooting ..................... Back cover

Specifications ........................ Back cover

4GB

This chapter provides information on the

location of buttons and how to use them to

perform basic operations.

However, some functions explained in this

section may not work depending on the model

of the receiver.

For the functions of the receiver you purchased,

refer to the Operating Instructions supplied

with the receiver.

Parts description

Location of Parts and Basic Remote

Operations

1 Function buttons

Press one of the buttons to select the

component you want to use. When you

press a button, the receiver turns on. The

components are factory assigned to the

buttons as follows. When you want to

assign other components, program the

remote following the steps on page 10.

Button(s)

Assigned

component(s)

VIDEO1

VCR (VTR mode 3)

VIDEO2

VCR (VTR mode 1)

VIDEO3

VCR (VTR mode 2)

DVD/LD

DVD player

TV/SAT

TV tuner

TAPE

Tape deck

MD/DAT

MD deck

CD/SACD

CD player

TUNER

Built-in tuner

PHONO

Turntable

See the table on page 9 for information on

the buttons that you can use to control each

component.

Note that the function buttons are factory-

set as described in the table above. If you

want to change the factory setting of the

buttons to match your particular

components, do the procedure

"Programming the remote" on page 10.

>10

MONITOR

2ND ROOM

VIDEO 1

VIDEO 2

VIDEO 3

DVD/LD

TV/SAT

TAPE

TV/VIDEO

MACRO 1

MACRO 2

CLEAR

SUB CH +

VOL +

POSITION

SWAP

MODE

ENTER

ANT

TV/VTR

D. SKIP/

CH/PRESET

MD/DAT CD/SACD

TUNER

PHONO

SHIFT

DISC

JUMP

AUTO DEC

DISPLAY

TEST

TONE

NIGHT

MODE

SCREEN

MAIN

EXIT/

RETURN

TITLE/

GUIDE

ENTER/

EXEC

MULTI/2CH

A. DIRECT

EQ/

TONE

MUTING

MODE

2CH

PRESET

P IN P

SOUND FIELD

D.TUNING

AV1

AV2

3RD

(SOURCE)

WIDE

/11

/10

/12

SLEEP

AV ? / 1

? / 1

SYSTEM

STANDBY

USE MODE

MASTER

VOL

Location

Parts

and

Basic

Remote

Operations

5GB

2 Remote mode buttons

Press to select the mode of the remote (page

15).

3 MACRO 1, 2 buttons

Press to use Macro Play function (page 14).

4 SOUND FIELD buttons

AUTO DEC button

Press to set the receiver to automatically

select the appropriate sound field for the

input signal.

This button can be used only with receivers

that have digital inputs.

MODE +/ buttons

Press to select sound fields.

2CH button

Press to turn the sound field off and listen to

2 channel stereo sound.

Multi channnel source is also downmixed to

a 2 channel stereo sound.

PRESET button

Press to select CINEMA STUDIO A, B, or

C, etc.

5 MULTI/2CH A. DIRECT* button

Press to select the multi channel input

sources.

continued

6 EQ/TONE button

Press to turn the tone effect on or off.

Note that if you have adjusted the tone

using the MAIN MENU button and cursor

buttons, the adjusted tone will be produced

whenever you turn on the tone effect.

7 MUTING button

Press to mute the sound.

8 ON SCREEN button*

Press to display the menus of the receiver

on the TV screen.

9 MASTER VOLUME +/ buttons

Press to adjust the volume level of all

speakers at the same time.

0 MAIN MENU button

Press to select the cursor mode of the

receiver (SET UP, LEVEL, etc.).

qa NIGHT MODE button*

Press to select NIGHT MODE.

qs TEST TONE button

Press to output a test tone.

qd SLEEP button

Press repeatedly to activate the sleep

function and the duration which the receiver

turns off automatically.

* Not available with STR-DA1ES.