Confidential
PCGA-UVC10
SERVICE MANUAL
Visual Communication Camera
For Japanese Area
Japanese Model
For American Area
US Model
Canadian Model
Illust : PCGA-UVC10
9-876-024-04
Ver 4-2004H
Revision History
· Design and specifications are subject to
change without notice.
Lineup : PCGA-UVC10
Japanese Model :
37
31
1/5.5 37
CMOS
2 2
F3.4
f=2.8 mm
f=40 mm 35 mm
50 Hz 60 Hz
YUY2 RGB 24
80 × 60 160 × 120 320 × 240 640 × 480
176 × 144 352 × 288
30
*
*
0.5 W
60 × 34 × 33 mm
100 cm
42 g
5°C 35°C
10°C
20% 80%
35°C
65%
29°C
20°C 60°C
10°C
10% 90%
60°C
20%
35°C
PCGA-UVC10
CD-ROM1
1
1
1
1
With You Call
1
1
Specifications
Visual Communication
Camera
370,000 pixels (effective pixels: 310,000)
Image pickup
1/5.5" 370,000-pixel color CMOS progressive
scanning image sensor.
Lens
2 groupsf 2 lenses, F3.4
Focal length f=0.2 in. (2.8 mm)
(equivalent to a 1.4 in. (35 mm) camera at f=1.6
in. (40 mm)
White balance
Auto/Indoors/Outdoors/Hold
Shutter speed
Auto/Hold
Flicker cancel function
Auto/50 Hz/60 Hz
Video capture format/size
YUY2/RGB, 24 bits
80
× 60, 160 × 120, 320 × 240, 640 × 480,
176
× 144, 352 × 288
Number of display frames
Maximum: 30 frames/sec*
* This rate differs depending on the specifications
of your computer and the application you are
using.
Power consumption
Approx. 0.5 W
External dimensions
Approx. 2.4
× 1.4 × 1.3 in. (60 × 34 × 33 mm)
(W
× H × D)
Cable length
Approx. 39.4 in. (100 cm)
Weight
Approx. 1.5 oz. (42 g) (main unit only)
Operating environment
Operating temperature
41
°F to 95°F (5°C to 35°C)
(temperature gradient less than 18
°F (10°C)/hour)
Operating humidity
20% to 80% (no condensation),
provided that humidity is less than 65% at 95
°F
(35
°C)
(hygrometer reading of less than 84
°F (29°C))
Storage temperature
4
°F to 140°F (20°C to 60°C)
(temperature gradient less than 18
°F (10°C)/hour)
Storage humidity
20% to 90% (no condensation),
provided that humidity is less than 20% at 140
°F
(60
°C)
(hygrometer reading of less than 95
°F (35°C))
Accessories
PCGA-UVC10 Installation Disc (CD-ROM
× 1)
Mounting adapter (1)
Adhesive sheet (1)
Visual Communication Camera Operating
Instructions (1)
Limited Warranty (1)
End User License Agreement (1)
2
PCGA-UVC10 (J/AM)
Confidential
Information in this document is subject to change without notice.
Sony, VAIO and CLIE are trademarks or registered trademarks of
Sony. Microsoft, Windows, Windows Media, Outlook, Bookshelf
and other Microsoft products are trademarks or registered trademarks
of Microsoft Corporation in the United State and other countries.
The word Bluetooth and the Bluetooth logo are trademarks of
Bluetooth SIG, Inc. AMD, AMD logo, AMD Duron and
combinations thereof, 3DNOW!, are trademarks of Advanced Micro
Devices, Inc. Intel Inside logo, Pentium and Celeron are trademarks
or registered trademarks of Intel Corparation. Transmeta, the
Transmeta logo, Crusoe Processor, the Crusoe logo and combinations
thereof are trademarks of Transmeta Corporation in the USA and
other countries. Graffiti, Hotsync, PalmModem, and Palm OS are
registered trademarks, and the Hotsync logo and Palm are trademarks
of Palm, Inc. or its subsidiaries. (M) and Motrola are trademarks of
Motrola, Inc. Other Motrola pruducts and services with (R) mark
like Dragomball are the trademarks of Motrola, Inc.
All other name of systems, products and services in this manual are
trademarks or registered trademarks of their respective owners.
In this manual, the (TM) or (R) mark are not specified.
Caution Markings for Lithium/Ion Battery - The following or similar
texts shall be provided on battery pack of equipment or in both the
operating and the service instructions.
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer. Discard used batteries according to the manufacturer's
instructions.
CAUTION: The battery pack used in this device may present a fire
or chemical burn hazard if mistreated. Do not disassemble, heat above
100
°C (212°F) or incinerate.
Dispose of used battery promptly.
Keep away from children.
CAUTION: Changing the back up battery.
· Overcharging, short circuiting, reverse charging, multilation or
incineration of the cells must be avoided to prevent one or more of
the following occurrence; release of toxic materials, release of
hydrogen and/or oxygen gas, rise in surface temperature.
· If a cell has leaked or vented, it should be replaced immediately
while avoiding to touch it without any protection.
Service and Inspection Precautions
1.
Obey precautionary markings and instructions
Labels and stamps on the cabinet, chassis, and components identify areas
requiring special precautions. Be sure to observe these precautions, as
well as all precautions listed in the operating manual and other associated
documents.
2.
Use designated parts only
The set's components possess important safety characteristics, such as
noncombustibility and the ability to tolerate large voltages. Be sure that
replacement parts possess the same safety characteristics as the originals.
Also remember that the
! mark, which appears in circuit diagrams and
parts lists, denotes components that have particularly important safety
functions; be extra sure to use only the designated components.
3.
Always follow the original design when mounting
parts and routing wires
The original layout includes various safety features, such as inclusion of
insulating materials (tubes and tape) and the mounting of parts above the
printer board. In addition, internal wiring has been routed and clamped so
as to keep it away from hot or high-voltage parts. When mounting parts
or routing wires, therefore, be sure to duplicate the original layout.
4.
Inspect after completing service
After servicing, inspect to make sure that all screws, components, and wiring
have been returned to their original condition. Also check the area around
the repair location to ensure that repair work has caused no damage, and
confirm safety.
5.
When replacing chip components...
Never reuse components. Also remember that the negative side of tantalum
capacitors is easily damaged by heat.
6.
When handling flexible print boards...
· The temperature of the soldering-iron tip should be about 270
°C.
· Do not apply the tip more than three times to the same pattern.
· Handle patterns with care; never apply force.
Caution: Remember that hard disk drives are easily damaged by
vibration. Always handle with care.
ATTETION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE !
!
!
!
! SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
3
PCGA-UVC10 (J/AM)
Confidential
4
PCGA-UVC10 (J/AM)
Confidential
5
PCGA-UVC10 (J/AM)
Confidential
History of the changes is shown as the
"Revision History" at the end of this data.
TABLE OF CONTENTS
Section
Title
Page
CHAPTER 1. SERVICE INFORMATION ................. 1-1
1-1. Locating the Controls and Connectors .................... 1-1
1-2. Connecting the Camera ........................................... 1-2
(to 1-3)
CHAPTER 2. EXPRODED VIEWS AND
PARTS LIST ..................................... 2-1
(to 2-1)
" Revision History "