Confidential
PCGA-HDM06
For Japanese Area
Japanese Model
For American Area
US Model
Canadian Model
Illust : PCGA-HDM06
9-876-037-05
Ver 5-2004H
Revision History
S400
Japanese Model :
Lineup : PCGA-HDM06
SERVICE MANUAL
HARD DISK DRIVE
· Design and specifications are subject to
change without notice.
Operating environment
Operating temperature
41
°F to 95°F (5°C to 35°C)
(temperature gradient less than 18
°F (10°C)/hour)
Operating humidity
20% to 80% (no condensation),
provided that humidity is less than 65% at 95
°F
(35
°C)
(hygrometer reading of less than 84
°F (29°C))
Storage temperature
4
°F to 140°F (20°C to 60°C)
(temperature gradient less than 18
°F (10°C)/hour)
Storage humidity
20% to 90% (no condensation),
provided that humidity is less than 20% at 140
°F
(60
°C)
(hygrometer reading of less than 95
°F (35°C))
Other specifications
Power consumption
Under normal conditions: approx. 4 W
Dimensions
Approx. 4.8
× 0.8 × 4.3 inches
(120
× 19 × 107 mm) (w × h × d)
(maximum dimensions including protruding parts)
Mass
Approx. 7.8 oz. (220 g) (main unit only)
60 G
1
1 1 G
10
NTFS
4200 rpm
20 M
/s*
20 M
/s*
*
i.LINK IEEE 1394
S400 4
1
S400=400 Mbps
AC
AC 100 V 240 V 50 60 Hz
AC 100 V
10 V 1.5 A
5
35
10
20 % 80 %
-20
60
10
20 % 90 %
4 W
120 19 107 mm
220 g
Specifications
Drive
Capacity
Approx. 60 GB 1)
Format
NTFS
Revolutions per minute
4200 rpm
Data transfer rate
Max:
20 Mbytes per second when reading 2)
20 Mbytes per second when writing 2)
1)
1 GB is equivalent to 1,000,000,000 bytes.
Available capacity may vary.
2)
Varies according to the workload of the
computer connected to the drive.
Connectors
i.LINK (IEEE 1394) S400 (4-pin) connector (1)
S400 = 400 Mbps
AC adapter
Power requirements
100-240 V AC, 50/60 Hz
Output voltage and current
10 V, 1.5 A (max.)
2
PCGA-HDM06 (J/AM)
Confidential
Caution Markings for Lithium/Ion Battery - The following or similar
texts shall be provided on battery pack of equipment or in both the
operating and the service instructions.
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer. Discard used batteries according to the manufacturer's
instructions.
CAUTION: The battery pack used in this device may present a fire
or chemical burn hazard if mistreated. Do not disassemble, heat above
100
°C (212°F) or incinerate.
Dispose of used battery promptly.
Keep away from children.
CAUTION: Changing the back up battery.
· Overcharging, short circuiting, reverse charging, multilation or
incineration of the cells must be avoided to prevent one or more of
the following occurrence; release of toxic materials, release of
hydrogen and/or oxygen gas, rise in surface temperature.
· If a cell has leaked or vented, it should be replaced immediately
while avoiding to touch it without any protection.
Service and Inspection Precautions
1.
Obey precautionary markings and instructions
Labels and stamps on the cabinet, chassis, and components identify areas
requiring special precautions. Be sure to observe these precautions, as
well as all precautions listed in the operating manual and other associated
documents.
2.
Use designated parts only
The set's components possess important safety characteristics, such as
noncombustibility and the ability to tolerate large voltages. Be sure that
replacement parts possess the same safety characteristics as the originals.
Also remember that the
! mark, which appears in circuit diagrams and
parts lists, denotes components that have particularly important safety
functions; be extra sure to use only the designated components.
3.
Always follow the original design when mounting
parts and routing wires
The original layout includes various safety features, such as inclusion of
insulating materials (tubes and tape) and the mounting of parts above the
printer board. In addition, internal wiring has been routed and clamped so
as to keep it away from hot or high-voltage parts. When mounting parts
or routing wires, therefore, be sure to duplicate the original layout.
4.
Inspect after completing service
After servicing, inspect to make sure that all screws, components, and wiring
have been returned to their original condition. Also check the area around
the repair location to ensure that repair work has caused no damage, and
confirm safety.
5.
When replacing chip components...
Never reuse components. Also remember that the negative side of tantalum
capacitors is easily damaged by heat.
6.
When handling flexible print boards...
· The temperature of the soldering-iron tip should be about 270
°C.
· Do not apply the tip more than three times to the same pattern.
· Handle patterns with care; never apply force.
Caution: Remember that hard disk drives are easily damaged by
vibration. Always handle with care.
ATTETION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE !
!
!
!
! SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
Information in this document is subject to change without notice.
Sony, VAIO and CLIE are trademarks or registered trademarks of
Sony. Microsoft, Windows, Windows Media, Outlook, Bookshelf
and other Microsoft products are trademarks or registered trademarks
of Microsoft Corporation in the United State and other countries.
The word Bluetooth and the Bluetooth logo are trademarks of
Bluetooth SIG, Inc. AMD, the AMD logo, other AMD product names
and combinations thereof are trademarks of Advanced Micro
Devices, Inc. Intel Inside logo, Pentium and Celeron are trademarks
or registered trademarks of Intel Corparation. Transmeta, the
Transmeta logo, Crusoe Processor, the Crusoe logo and combinations
thereof are trademarks of Transmeta Corporation in the USA and
other countries. Graffiti, Hotsync, PalmModem, and Palm OS are
registered trademarks, and the Hotsync logo and Palm are trademarks
of Palm, Inc. or its subsidiaries. (M) and Motrola are trademarks of
Motrola, Inc. Other Motrola pruducts and services with (R) mark
like Dragomball are the trademarks of Motrola, Inc.
All other name of systems, products and services in this manual are
trademarks or registered trademarks of their respective owners.
In this manual, the (TM) or (R) mark are not specified.
3
PCGA-HDM06 (J/AM)
Confidential
4
PCGA-HDM06 (J/AM)
Confidential
5
PCGA-HDM06 (J/AM)
Confidential
TABLE OF CONTENTS
Section
Title
Page
CHAPTER 1. SERVICE INFOMATION ........................ 1-1
(to 1-14)
CHAPTER 2. BLOCK DIAGRAM...................................2-1
(to 2-1)
CHAPTER 3. FRAME HARNESS DIAGRAMS ........ 3-1
(to 3-1)
CHAPTER 4. EXPLODED VIEWS AND PARTS LIST
4-1. Main Section ..................................................................... 4-1
4-2. Accessories ....................................................................... 4-2
(to 4-2)
CHAPTER 5. OTHERS
5-1. The Barcode Label ........................................................... 5-1
(to 5-1)
History of the changes is shown as the
"Revision History" at the end of this data.
" Revision History "
Note: The parts location index which precedes
every schematic diagram, serves as the
electrical part list too.