REVISION HISTORY
AG3E
MODEL
KV-DR29M61
KV-DR29M81
PART NO. :
9-872-369-01
NO.
SUFFIX
DATE
SUPP / CORR
DESCRIPTION
1
-01
2003/8
_ _
1st Issue
CHASSIS
MODEL
COMMANDER DEST. CHASSIS NO.
CHASSIS
TRINITRON ® COLOR TV
SERVICE MANUAL
AG3E
MODEL
COMMANDER DEST.
CHASSIS NO.
KV-DR29M61 RM-991 GE
SCC-U84C-A
KV-DR29M81 RM-991 ME
SCC-U43D-A
2
KV-DR29M61/DR29M81
RM-991
Power requirements
110-240V AC, 50/60 Hz
Power consumption (W)
Indicated on the rear of the TV
Television system
B/G, I, D/K, M
Color system
PAL, PAL 60, SECAM, NTSC3.58, NTSC4.43
Stereo/Bilingual system
NICAM Stereo/Bilingual B/G, I;
KV-DR29M61
A2 Stereo/Bilingual B/G
Teletext language
English, Arabic, French
KV-DR29M61
English, Farsi(Persian), French
KV-DR29M81
Channel coverage
B/G
VHF: E2 to E12
UHF: E21 to E69
CATV: S01 to S03, S1 to S41
I
UHF: B21 to B68
CATV: S01 to S03, S1 to S41
D/K
VHF: C1 to C12, R1 to R12
UHF: C13 to C57, R21 to R60
CATV: S01 to S03, S1 to S41, Z1 to Z39
M
VHF: A2 to A13
UHF: A14 to A79
CATV: A-8 to A-2, A to W+4, W+6 to W+84
8
(Antenna)
75-ohm external terminal
Audio output (Speaker)
8W + 8W
Number of terminal
DVideo
Input: 4
Output: 1
Phone jacks; 1 Vp-p, 75 ohms
9 Audio
Input: 4
Output: 1
Phone jacks; 500 mVrms
(S Video)
Input : 2
Y: 1 Vp-p, 75 ohms
unbalanced, sync negative
C: 0.286 Vp-p, 75 ohms
(Component
Input : 1
Phono jacks:
Video)
Y: 1 Vp-p, 75 ohms, sync negative
PB/CB: 0.7 Vp-p, 75 ohms
PR/CR: 0.7 Vp-p, 75 ohms
Audio: 500mVrms
2 (Headphone)
Output: 1
Stereo minijack
Picture tube
29 in
Tube size (cm)
72
Measured diagonally
Screen size (cm)
68
Measured diagonally
Dimension (w/h/d,mm)
786
× 596 × 514
Mass (kg)
52
Design and specifications are subject to change without notice.
SPECIFICATIONS
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK
! ON
THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND
THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR
CARBON PAINTED ON THE CRT, AFTER REMOVING THE
ANODE.
Note
3
KV-DR29M61/DR29M81
RM-991
TABLE OF CONTENTS
SELF DIAGNOSTIC FUNCTION .......................................4
1. DISASSEMBLY
1-1.
Rear Cover Removal .................................................. 7
1-2.
Speaker Removal ........................................................ 7
1-3.
Chassis Assy Removal ................................................ 7
1-4.
Service Position .......................................................... 7
1-5.
Service Position on TV Stand .................................... 7
1.6.
Terminal Bracket Removal ......................................... 8
1-7.
B3 and D5 Boards Removal ....................................... 8
1-8.
F1 Board Removal ...................................................... 8
1-9.
BC1 and V2 Boards Removal .................................... 8
1-10. H1 and H2 Boards Removal ...................................... 8
1-11. A and D Boards Removal ........................................... 8
1-12. Picture Tube Removal ................................................ 9
2. SERVICE JIG .............................................................. 11
3. CIRCUIT BOARDS LOCATION ................................. 11
4. ADVANCE OPERATION
4-1.
"RESET" Function ................................................... 12
5. SET-UP ADJUSTMENTS
5-1.
Beam Landing .......................................................... 13
5-2.
Convergence Adjustment ......................................... 14
5-3.
Focus Adjustment ..................................................... 16
5-4.
Neck Assy Twist Adjustment ................................... 16
5-5.
G2 (SCREEN) and White Balance Adjustments ..... 16
6. CIRCUIT ADJUSTMENTS
6-1.
Adjustments With Commander ................................ 17
6-2.
Adjustment Method .................................................. 17
6-3.
Picture Quality Adjustments .................................... 36
6-4.
Sub Hue/Col Adjustment .......................................... 36
6-5.
Deflection Adjustments ............................................ 37
6-6.
A Board Adjustment After IC003 (MEMORY)
Replacement ............................................................. 38
6-7.
Picture Distortion Adjustment .................................. 39
Section
Title
Page
Section
Title
Page
7. DIAGRAMS
7-1.
Block Diagram ......................................................... 40
7-2.
Schematic Diagrams ................................................. 49
(1) A Board Schematic Diagrams ............................ 50
(2) B3 Board Schematic Diagram ............................ 54
(3) D Board Schematic Diagram .............................. 56
(4) D5 Board Schematic Diagram ........................... 58
(5) C Board Schematic Diagram .............................. 60
(6) V2 Board Schematic Diagram ............................ 62
(7) BC1 Board Schematic Diagram ......................... 64
(8) H1, H2 and J Boards Schematic Diagrams ........ 66
(9) F1 and VM Boards Schematic Diagram ............ 68
7-3.
Voltage Measurement and Waveforms ..................... 71
7-4.
Printed Wiring Boards and Parts Location .............. 86
7-5.
Semiconductors ........................................................ 99
8. EXPLODED VIEWS
8-1.
Speaker Bracket ...................................................... 101
8-2.
Chassis .................................................................... 102
8-3.
Picture Tube ............................................................ 103
9. ELECTRICAL PARTS LIST ...................................... 104
OPERATING INSTRUCTIONS
4
KV-DR29M61/DR29M81
RM-991
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically
begin to flash.
The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER
lamp flash indicators is listed in the instruction manual for the user's knowledge and reference. If an error symptom cannot
be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past
problems and how often these problems occur.
1. DIAGNOSTIC TEST INDICATORS
When an error occurs, the STANDBY/TIMER lamp will flash a number of times to indicate the possible cause of the
problem. If there is more than one error, the lamp will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen. No error has occured if the screen displays a "0".
Diagnostic
Item
Description
· Power does not
turn on
· +B overcurrent
(OCP)
· +B overvoltage
(OVP)
· Vertical deflection
failure
· White balance
failure (no
PICTURE)
· Horizontal
deflection failure
· Micro reset
No. of times
STANDBY/TIMER
lamp flashes
Does not light
2 times
3 times
4 times
5 times
6 times
--
Self-diagnostic
display/Diagnostic
result
--
002:000 or
002:001~255
003:000 or
003:001~255
004:000 or
004:001~255
005:000 or
005:001~255
006:000 or
006:001~225
101:00 or
101:001~225
Probable
Cause
Location
· Power cord is not plugged
in.
· Fuse is burned out F1601
(F1 Board)
· H.OUT Q6807 is shorted.
· H.IN Q6810 is shorted.
Q6802 shorted.
· PH6602 faulty.
D6644 faulty, R6651 open.
· 10.5V is not supplied.
(D board)
· V.OUT IC6800 faulty
D6816 faulty
D6817 faulty
D6824 faulty
R6852 open
R6851 open (D board)
· G2 is improperly adjusted.
(Note 2)
· CRT problem.
· Video OUT IC9001, 9002,
9003 are faulty. (C board)
· IC8306 (A board) and
IC4301 (A board) are faulty.
· C6831 is open circuit.
PS6606 open, PS6605
open. (D board)
· CRT Discharge (C Board)
· Static discharge
· External noise
Detected
Symptoms
· Power does not come on.
· No power is supplied to the
TV.
· AC power supply is faulty.
· Power does not come on.
· Load on power line is
shorted.
· Power does not come on.
· Vertical deflection pulse is
stopped.
· Vertical size is too small.
· Vertical deflection stopped.
· No raster is generated.
· CRT cathode current
detection reference pulse
output is small.
· H pulse output is too high.
· Power is shut down shortly,
after this return back to
normal.
· Detect Micro latch up.
Note 1: Refer to screen (G2) Adjustment in section 5-5 of this manual.
SELF DIAGNOSTIC FUNCTION