HCD-CP333
US Model
Canadian Model
AEP Model
UK Model
E Model
SERVICE MANUAL
MICRO HI-FI COMPONENT SYSTEM
-- Continued on next page --
SPECIFICATIONS
Ver 1.1 2003. 11
· HCD-CP333 is the Amplifier, CD player,
Tape Deck and Tuner section in
CMT-CP333.
Sony Corporation
Home Audio Company
Published by Sony Engineering Corporation
9-877-051-02
2003K16-1
© 2003.11
Amplifier section
For the U.S. model
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
With 6-ohm loads, both channels driven, from
120 - 10,000 Hz; rated 40 watts per channel
minimum RMS power, with no more than 10%
total harmonic distortion from 250 milliwatts to
rated output.
North American model
Continuous RMS power output (reference):
40 + 40 W
(6 ohms at 1 kHz, 10%
THD)
Total harmonic distortion less than 0.07% (6 ohms at
1 kHz, 32 W)
European model
DIN power output (rated): 32 + 32 W
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference):
40 + 40 W
(6 ohms at 1 kHz, 10%
THD)
Music power output (reference):
100 + 100 W
Other models
The following measured at 230 V AC, 60 Hz
DIN power output (rated): 30 + 30 W
(6 ohms at 1 kHz, DIN)
Laser
Semiconductor laser
(
= 780 nm)
Emission
duration: continuous
Wavelength
780 - 790 nm
Frequency response
20 Hz - 20 kHz (
±0.5 dB)
Tape player section
Recording system
4-track 2-channel stereo
Frequency response
50 - 13,000 Hz (
±3 dB),
using a Sony TYPE I
cassette
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
North American model:
87.5 - 108.0 MHz
(100-kHz step)
Other models:
87.5 - 108.0 MHz
(50-kHz step)
Antenna
FM wire antenna
Antenna terminals
75 ohm unbalanced
Intermediate frequency
10.7 MHz
Continuous RMS power output (reference):
38 + 38 W
(6 ohms at 1 kHz, 10%
THD)
The following measured at 220 V AC, 60 Hz
DIN power output (rated): 27 + 27 W
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference):
35 + 35 W
(6 ohms at 1 kHz, 10%
THD)
Inputs
AUDIO IN MD (VIDEO) (phono jacks):
Sensitivity 500/250 mV,
impedance 47 kilohms
Outputs
CD DIGITAL OUT OPTICAL:
Optical
PHONES:
Accepts headphones with
an impedance of 8 ohms
or more
SPEAKER:
6 ohms
CD player section
System
Compact disc and digital
audio system
Model Name Using Similar Mechanism
HCD-CP300
CD Mechanism Type
CDM63K-K6BD44
Optical Pick-up Type
KSM-213D
Model Name Using Similar Mechanism
HCD-CP300
Tape Transport Mechanism Type
CMBL6Z511A
CD
Section
Tape deck
Section
2
HCD-CP333
TABLE OF CONTENTS
General
Power requirements
North American model:
120 V AC, 60 Hz
European model:
230 V AC, 50/60 Hz
Other models:
110 - 120 V or 220 -
240 V AC , 50/60 Hz
Adjustable with voltage
selector
Power consumption
European model
70 W
0.4 W (at the power
saving mode)
Other models:
70 W
Dimensions (w/h/d)
Approx. 225
× 273 ×
385 mm incl. projecting
parts and controls
Mass
Approx. 7.3 kg
AM tuner section
Tuning range
North American model:
530 - 1,710 kHz
(with the tuning interval
set at 10 kHz)
531 - 1,710 kHz
(with the tuning interval
set at 9 kHz)
European model:
531 - 1,602 kHz
(with the tuning interval
set at 9 kHz)
Other models:
530 - 1,710 kHz
(with the tuning interval
set at 10 kHz)
531 - 1,602 kHz
(with the tuning interval
set at 9 kHz)
Antenna
AM loop antenna, external
antenna terminal
Intermediate frequency
450 kHz
·Design and specifications are subject to change without notice.
1. SERVICING NOTES ························································· 4
2. GENERAL ············································································ 5
3. DISASSEMBLY ·································································· 7
3-1. Cover (Upper) ································································· 8
3-2. Front Panel Section ························································· 8
3-3. Tape Mechanism Deck-1 ················································ 9
3-4. Tape Mechanism Deck-2 ················································ 9
3-5. LED Board, CONTROL Board ···································· 10
3-6. Back Panel Sub Assy, JACK Board ······························ 10
3-7. MAIN Board ································································· 11
3-8. POWER Board ······························································ 11
3-9. CD Mechanism Deck (CDM63K-K6BD44) ················ 12
3-10. CD Board ······································································ 12
3-11. Base Unit (BU-K6BD44) ············································· 13
3-12. Tray Assy ······································································ 13
3-13. Silder (Loading) ···························································· 14
3-14. TRAY SENSOR Board, MOTOR Board ······················ 14
3-15. IN OUT SW Board ······················································· 15
3-16. Stocker Assy ································································· 15
3-17. CD Base Unit Assy, DISC SENSOR Board ················· 16
4. TEST MODE ······································································ 17
5. ELECTRICAL ADJUSTMENTS ································· 18
6. DIAGRAMS ······································································· 20
6-1. Note For Printed Wiring Boards And Schematic
Diagrams ······································································· 20
6-2. Block Diagrams ···························································· 21
6-3. Circuit Boards Location ················································ 23
6-4. Printed Wiring Board CD Board ··························· 24
6-5. Schematic Diagram - CD Board - ································· 25
6-6. Printed Wiring Board TC Board ····························· 26
6-7. Schematic Diagram TC Board ································ 27
6-8. Printed Wiring Board MAIN Board ······················· 28
6-9. Schematic Diagram MAIN Board (1/3) ················· 29
6-10. Schematic Diagram MAIN Board (2/3) ················· 30
6-11. Schematic Diagram MAIN Board (3/3) ················· 31
6-12. Printed Wiring Board CONTROL Section ············· 32
6-13. Schematic Diagram CONTROL Section ················ 33
6-14. Printed Wiring Board DRIVER Section ················· 34
6-15. Schematic Diagram DRIVER Section ···················· 35
6-16. Printed Wiring Board POWER Board ···················· 36
6-17. Schematic Diagram POWER Board ······················· 37
6-18. Printed Wiring Board LCD Section ························ 38
6-19. Schematic Diagram LCD Section ··························· 38
6-20. IC Pin Function Description ········································· 39
6-21. IC Block Diagrams ······················································· 41
7. EXPLODED VIEWS ························································ 44
7-1. Cover Section ································································ 44
7-2. Front Panel Section ······················································· 45
7-3. Chassis Section ····························································· 46
7-4. CD Mechanism Deck-1 ················································ 47
7-5. CD Mechanism Deck-2 ················································ 48
7-6. KSM-213D ··································································· 49
8. ELECTRICAL PARTS LIST ········································· 50
Ver 1.1 2003.11
3
HCD-CP333
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
This appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
Notes on chip component replacement
·Never reuse a disconnected chip component.
· Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing
·Keep the temperature of the soldering iron around 270 °C dur-
ing repairing.
· Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
· Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, "metallized" knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers' instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The "limit" indication is 0.75
V, so analog meters must have an accurate low-voltage scale.
The Simpson 250 and Sanwa SH-63Trd are examples of a
passive VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2 V AC range are suitable. (See Fig. A)
Fig. A.
Using an AC voltmeter to check AC leakage.
1.5 k
0.15
µF
AC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
4
HCD-CP333
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
SERVICE POSTION
In checking the CD block, prepare jig (extension cable J-2501-011-
B).
SECTION 1
SERVICING NOTES
Connect jig (extension cable J-2501-011-B)
to the MAIN board (CN304) and CD board (CN101).
MAIN board
CD board
MODEL IDENTIFICATION
-- BACK PANEL --
Parts No.
Power Voltage Indication
VOLTAGE SELECTOR
Switch
MODEL
PARTS No.
AEP model
4-233-470-3s
UK model
4-233-470-3s
US model
4-233-470-4s
Canadian model
4-233-470-4s
E model
4-233-470-5s
AC:110-120/220-240V
50/60Hz 70W
POWER VOLTAGE INDICATION
AC:230V 50/60Hz 70W
AC:120V 60Hz 70W
5
HCD-CP333
SECTION 2
GENERAL
1 DISC indicator wa
BASS ea
CD 1 wd
CD 1 Z wf
CD 2 wg
CD 2 Z wh
CD 3 wj
CD 3 Z wk
CD SYNC 7
CD u ws
CD x qj
CD ./> qk
CD m/M qk
DECK A EJECT Z 5
DECK B EJECT Z 6
DSG 4
FUNCTION es
PHONES jack wl
PLAY MODE w;
Remote sensor 3
REPEAT ql
TAPE A N 1
TAPE B Y 0
TAPE A x 2
TAPE B x qa
TAPE A m/M ef
TAPE B m/M qs
TAPE REC z 8
TAPE X 9
TREBLE e;
TUNER BAND qd
TUNING MODE qf
TUNING +/ qg
VOLUME qh
BUTTON DESCRIPTIONS
@/1 (power) ed
1234
5
~69
8
7q;
qa
qs
qd
qf
qg
qh
qj
qk
wl
e;
ed
es
ea
ef
wd
~wk
ws
w;
wa
ql
Y
?/1
x
Mx
m
M
m
M
X
z
Z
Z
ux
.
>
m
M
Z
ZZ
Main unit
This section is extracted
from instruction manual.