SERVICE MANUAL
CD/DVD PLAYER
System
Laser: Semiconductor laser
Signal format system: NTSC
Audio characteristics
Frequency response: DVD VIDEO
(PCM 96 kHz): 2 Hz to 44 kHz (44
kHz: 2 dB ±1.0 dB)/
Super Audio CD: 2 Hz to 100 kHz
(50 kHz: 3 dB ±1 dB)/
CD: 2 Hz to 20 kHz (±0.5 dB)
Signal-to-noise ratio (S/N ratio): 115 dB
(LINE OUT L/R (AUDIO) jacks only)
Harmonic distortion: 0.003%
Dynamic range: DVD VIDEO/Super
Audio CD: 103 dB/CD: 99 dB
Wow and flutter: Less than detected value
(±0.001% W PEAK)
Outputs
(Jack name: Jack type/Output level/
Load impedance)
LINE OUT (AUDIO): Phono jack/
2 Vrms/ 10 kilohms
5.1CH OUTPUT: Phono jack/
2 Vrms/ 10 kilohms
DIGITAL OUT (OPTICAL):
Optical output jack/18 dBm (wave
length 660 nm)
DIGITAL OUT (COAXIAL): Phono jack/
0.5 Vp-p/75 ohms
COMPONENT VIDEO OUT
(Y, PB, PR): Phono jack/
Y: 1.0 Vp-p/PB, PR:
interface*1 = 0.648 Vp-p, or
interface*2 = 0.7 Vp-p/75 ohms
*1
BLACK LEVEL (COMPONENT OUT)
is ON
*2
BLACK LEVEL (COMPONENT OUT)
is OFF
LINE OUT (VIDEO): Phono jack/
1.0 Vp-p 75 ohms
S VIDEO OUT: 4-pin mini DIN/Y:
1.0 Vp-p, C: 0.286 Vp-p/75 ohms
SPECIFICATIONS
General
Power requirements:
120 V AC, 60 Hz
110 240 V AC, 50/60 Hz
Power consumption: 12 W
Dimensions (approx.):
430
× 55.5 × 239 mm
(17
× 2 1/4 × 9 1/2 in.)
(width/height/depth) incl. projecting
parts
Mass (approx.): 2.0 kg (4 27/64 lb)
Operating temperature: 5°C to 35°C
(41°F to 95°F)
Operating humidity: 25% to 80%
Supplied accessories
See page 18
Specifications and design are subject to
change without notice.
ENERGY STAR is a U.S. registered mark.
As an
ENERGY STAR Partner, Sony
Corporation has determined that this
product meets the
ENERGY STAR
guidelines for energy efficiency.
USA Model
Canadian Model
Singapore Model
Australian Model
DVP-NS775V/NS780V
RMT-D171A/RMT-D171P
Notes: USA and Canadian model only
Photo : DVP-NS775V
RMT-D171A
2
DVP-NS775V/NS780V
SAFETY CHECK-OUT
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are "pinched"
or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transis-
tors, that were installed during a previous repair. Point them out
to the customer and recommend their replacement.
4. Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and recommend
their replacement.
5. Check the line cord for cracks and abrasion.
Recommend the replacement of any such line cord to the cus-
tomer.
6. Check the B+ voltage to see it is at the values specified.
7. Check the antenna terminals, metal trim, "metallized" knobs,
screws, and all other exposed metal parts for AC leakage. Check
leakage as described below.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO
CONFIRM LASER BEAM EMISSION, BE SURE TO OBSERVE
FROM A DISTANCE OF MORE THAN 25 cm FROM THE SURFACE
OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
CAUTION:
The use of optical instrument with this product will increase eye
hazard.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
OR DOTTED LINE
WITH MARK
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE
COMPONENTS WITH
SONY
PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5mA (500 microampers).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers' instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC volmeter. The "limit" indication
is 0.75V, so analog meters must have an accurate low voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples of
a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
· Unleaded solder melts at a temperature about 40°C highter than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
· Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
· Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may also
be added to ordinary solder.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE
SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT
CRITIQUES
POUR
LA
SÉCURITÉ
DE
FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS
QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS
PUBLIÉS PAR SONY.
To Exposed Metal
Parts on Set
0.15 F
1.5k
AC
Voltmeter
(0.75 V)
Earth Ground
Fig.A. Using an Acvoltmeter to check AC leakage.
3
DVP-NS775V/NS780V
TABLE OF CONTENTS
SERVICE NOTE
1.
Disc Removal Procedure (at POWER OFF) .............. 5
2.
PWB caution for B3834 ................................................. 5
1.
GENERAL
Precautions .................................................................... 1-1
About this Manual .......................................................... 1-1
This Player Can Play the Following Discs ................... 1-1
Notes about the Discs .................................................. 1-1
Index to Parts and Controls ......................................... 1-2
Guide to the Control Menu Display .............................. 1-3
Hookups ................................................................................ 1-3
Hooking Up the Player .................................................. 1-3
Step 1: Unpacking ......................................................... 1-3
Step 2: Inserting Batteries into the Remote ................. 1-3
Step 3: Connecting the Video Cords ............................ 1-4
Step 4: Connecting the Audio Cords ............................ 1-5
Step 5: Connecting the Power Cord ............................. 1-6
Step 6: Quick Setup ...................................................... 1-6
Playing Discs ......................................................................... 1-7
Playing Discs ................................................................. 1-7
Resuming Playback from the Point Where You
Stopped the Disc (Multi-disc Resume) .................. 1-8
Using the DVD's Menu .................................................. 1-8
Selecting "ORIGINAL" or "PLAY LIST" on a
DVD-RW ................................................................... 1-8
Selecting a Playback Area for a Super Audio CD ....... 1-8
Playing VIDEO CDs With PBC Functions
(PBC Playback) ........................................................ 1-9
Various Play Mode Functions (Program Play,
Shuffle Play, Repeat Play, A-B Repeat Play ........... 1-9
Searching for a Scene .......................................................... 1-10
Searching for a Particular Point on a Disc (Search,
Scan, Slow-motion Play, Freeze Frame) ............... 1-10
Searching for a Title/Chapter/Track/Scene, etc.
(Search mode) ......................................................... 1-10
Searching by Scene (PICTURE NAVIGATION) ......... 1-11
Viewing Information About the Disc ..................................... 1-11
Checking the Playing Time and Remaining Time ........ 1-11
Sound Adjustments ............................................................... 1-12
Changing the Sound ...................................................... 1-12
Surround Mode Settings ............................................... 1-12
Enjoying Movies .................................................................... 1-13
Changing the Angles ..................................................... 1-13
Displaying the Subtitles ................................................. 1-13
Adjusting the Playback Picture
(CUSTOM PICTURE MODE) ................................. 1-13
Sharpening the Pictures (SHARPNESS) ..................... 1-14
Enjoying MP3 Audio and JPEG Images .............................. 1-14
About MP3 Audio Tracks and JPEG Image Files ....... 1-14
Playing DATA CDs with MP3 Audio Tracks and
JPEG Image Files .................................................... 1-14
Enjoying JPEG Images as a Slide Show ..................... 1-15
Using Various Additional Functions ...................................... 1-16
Locking Discs (CUSTOM PARENTAL CONTROL,
PARENTAL CONTROL) .......................................... 1-16
Controlling Your TV or AV Amplifier (Receiver)
With the Supplied Remote ....................................... 1-17
Settings and Adjustments ..................................................... 1-18
Using the Setup Display ............................................... 1-18
Setting the Display or Sound Track Language
(LANGUAGE SETUP) ............................................. 1-18
Settings for the Display (SCREEN SETUP) ................ 1-18
Custom Settings (CUSTOM SETUP) .......................... 1-19
Settings for the Sound (AUDIO SETUP) ..................... 1-19
Settings for the Speakers (SPEAKER SETUP) .......... 1-19
Additional Information ............................................................ 1-20
Troubleshooting ............................................................. 1-20
Self-diagnosis Function (When letters/
numbers appear in the display ................................ 1-21
Glossary ........................................................................ 1-21
Specifications ................................................................. 1-22
2.
DISASSEMBLY
2-1.
Upper Case ................................................................... 2-1
2-2.
Front Panel Assembly ................................................... 2-1
2-3.
Loading Assembly ......................................................... 2-2
2-4.
Optical Device (KHM-310BAA) .................................... 2-3
2-5.
DC Motor and PL-035 Board ........................................ 2-4
2-6.
AV-086 and IF-115 Boards ........................................... 2-4
2-7.
MB-117 Board ................................................................ 2-5
2-8.
Switching Regulator ...................................................... 2-5
2-9.
Interval Views ................................................................. 2-6
2-10. Circuit Boards Location ................................................. 2-7
3.
BLOCK DIAGRAMS
3-1.
Overall Block Diagram .................................................. 3-1
3-2.
System Control/Signal Processor Block Diagram ...... 3-3
3-3.
RF/Servo Block Diagram .............................................. 3-5
3-4.
Audio (1) Block Diagram ............................................... 3-7
3-5.
Audio (2) Block Diagram ............................................... 3-9
3-6.
Video Block Diagram ..................................................... 3-11
3-7.
Interface Control Block Diagram .................................. 3-13
3-8.
Power (1) Block Diagram .............................................. 3-15
3-9.
Power (2) Block Diagram .............................................. 3-17
3-10. Power (3) Block Diagram .............................................. 3-19
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1.
Frame Schematic Diagram ........................................... 4-1
4-2.
Printed Wiring Boards and Schematic Diagrams ........ 4-3
Waveform ...................................................................... 4-4
·
MB-117 Printed Wiring Board .................................. 4-5
·
MB-117 (System) Schematic Diagram .................. 4-7
·
MB-117 (RF-Servo) Schematic Diagram ............... 4-9
·
MB-117 (8ch DAC) Schematic Diagram ................ 4-11
·
MB-117 (Ps-Trough) Schematic Diagram .............. 4-13
·
AV-086 Printed Wiring Board ................................... 4-15
·
AV-086 (Video) Schematic Diagram ........................ 4-17
·
AV-086 (Audio 1/2) Schematic Diagram ................. 4-19
·
AV-086 (Audio 2/2) Schematic Diagram ................. 4-21
·
IF-115 Printed Wiring Board .................................... 4-23
·
IF-115 (Interface) Schematic Diagram .................. 4-25
·
PL-035 Printed Wiring Board ................................... 4-27
·
PL-035 (Power Switch) Schematic Diagram .......... 4-29
·
Power Block (SRV1577UC)
Printed Wiring Board ........................................... 4-31
·
Power Block (SRV1577UC)
Schematic Diagram ............................................ 4-33
·
Power Block (SRV1578WW)
Printed Wiring Board ........................................... 4-35
·
Power Block (SRV1578WW)
Schematic Diagram ............................................ 4-37
4
DVP-NS775V/NS780V
5.
IC PIN FUNCTION DESCRIPTION
5-1.
System Control-Video Pin Function
(MB-117 BOARD IC102) .............................................. 5-1
6.
TEST MODE
6-1.
General Description ...................................................... 6-1
6-2.
Starting Test Mode ........................................................ 6-1
6-3.
Drive Manual Operation ................................................ 6-1
6-4.
Mirror Time Adjustment ................................................. 6-1
6-5.
Executing IOP Measurement ....................................... 6-3
6-6.
If Con Self Diagnostic Function .................................... 6-3
6-7.
Emergency History Check ........................................... 6-4
7.
ELECTRICAL ADJUSTMENT
7-1.
Power Supply Adjustment ............................................. 7-1
7-2.
Adjustment of Video System ......................................... 7-2
8.
REPAIR PARTS LIST
8-1.
Exploded Views ............................................................. 8-1
8-1-1. Main Section ............................................................. 8-1
8-1-2. Mechanism Deck Assembly .................................... 8-3
8-2.
Electrical Parts List ....................................................... 8-4
5
DVP-NS775V/NS780V
SERVICE NOTE
1. DISC REMOVAL PROCEDURE (at POWER OFF)
1) Open dust cover to access to a hole insert a tapering driver into the aperture of the unit bottom, and move the lever of chuck can in the
direction of the arrow A. (See Fig. 1)
2) Draw out the tray in the direction of the arrow B, and remove a disc. (See Fig. 1)
2. PWB caution for B3834
Please ignore screw mark on A side.
Refer B side indication;
QS
: screw mount for NS995V
AV
: screw mount for NS775V
The lever of a zipper cam
B
A
Hold
Tray
Fig. 1.