CD/DVD PLAYER
SPECIFICATIONS
DVP-NC615/NC655P
RMT-D143A/D143E/D143P/D144A
US Model
DVP-NC615/NC655P
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Singapore Model
PX Model
DVP-NC615
SERVICE MANUAL
System
Laser: Semiconductor laser
Signal format system:
U.S./Canadian models: NTSC
Asian/Oceanian models: PAL/NTSC
UK/European models: PAL/(NTSC)
(See page 1-3 to switch.)
Audio characteristics
Frequency response: DVD VIDEO (PCM
96 kHz): 2 Hz to 44 kHz (
±1.0 dB)/DVD
VIDEO (PCM 48 kHz): 2 Hz to 22 kHz
(
±0.5dB)/CD: 2Hz to 20 kHz (±0.5 dB)
Signal-to-noise ratio (S/N ratio): 115 dB
(LINE OUT L/R (AUDIO) jacks only)
Harmonic distortion: 0.003 %
Dynamic range: DVD VIDEO: 103 dB/CD:
99 dB
Wow and flutter: Less than detected value
(
±0.001% W PEAK)
The signals from LINE OUT L/R (AUDIO)
jacks are measured. When you play PCM
sound tracks with a 96 kHz sampling
frequency, the output signals from the
DIGITAL OUT (COAXIAL) jack are
converted to 48 kHz sampling frequency.
Outputs
(Jack name: Jack type/Output level/Load
impedance)
LINE OUT L/R (AUDIO): Phono jack/
2 Vrms/10 kilohms
DIGITAL OUT (COAXIAL): Phono jack/
0.5 Vp-p/75 ohms
COMPONENT VIDEO OUT(Y, PB/CB, PR/
CR): Phono jack/Y: 1.0 Vp-p/PB, PR,CB,
CR,: 0.7 Vp-p/75 ohms (US/Canadian/
Asian/Oceanian models)
LINE OUT (VIDEO): Phono jack/1.0 Vp-p/
75 ohms
S VIDEO OUT: 4-pin mini DIN/
Y: 1.0 Vp-p/C:0.3 Vp-p (PAL),
0.286 Vp-p (NTSC)/75 ohms
General
Power requirements:
120 V AC, 60 Hz
110 to 240V AC, 50/60 Hz
220 to 240V AC, 50/60 Hz
See page 1-1 for further information.
Power consumption: 13 W/14 W
See page 1-1 for further information.
Mass (approx.): 5.1 kg (11 lb 4 oz)
Operating temperature: 5
° C to 35 ° C
(41
° F to 95 ° F)
Operating humidity: 25 % to 80 %
Supplied accessories
See page 1-3.
Specifications and design are subject to
change without notice.
ENERGY STARR is a U.S. registered mark.
As an
ENERGY STARR Partner, Sony
Corporation has determined that this product
meets the
ENERGY STARR guidelines for
energy efficiency.
DIGITAL OUT (OPTICAL): Optical
output jack/18 dBm (wave length
660 nm) (UK/European models)
Dimensions (approx.): 430
× 108 × 409 mm
430
× 108 × 411 mm
(1
(NC615: UK, European models)
7
× 4 3/8 × 16 1/8 in.):(NC615: US,
(17
× 4 3/8 × 16 3/8 in.):
430
× 108 × 413 mm
(NC655P model)
(17
× 4 3/8 × 16 1/4 in.):
(width/height/depth)
incl. projecting parts
Canadian, Asian, Oceanian models)
Photo : DVP-NC655P (SILVER)
RMT-D144A
-- 2 --
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the line cord for cracks and abrasion.
Recommend the replacement of any such line cord to the
customer.
6.
Check the B+ voltage to see it is at the values specified.
7.
Check the antenna terminals, metal trim, "metallized" knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5mA (500 microampers).
Leakage current can be measured by any one of three methods.
1.
A commercial leakage tester, such as the Simpson 229 or RCA
TW-540A. Follow the manufacturers' instructions to use these
instruments.
2.
A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3.
Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The "limit" indication
is 0.75V, so analog meters must have an accurate low voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
· Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
· Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
· Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
To Exposed Metal
Parts on Set
0.15
µF
1.5 k
AC
Voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH
THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO
CONFIRM LASER BEAM EMISSION, BE SURE TO OBSERVE
FROM A DISTANCE OF MORE THAN 25 cm FROM THE SURFACE
OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
CAUTION:
The use of optical instrument with this product will increase eye
hazard.
-- 3 --
TABLE OF CONTENTS
SERVICE NOTE
1.
NOTE ON REMOVING THE UPPER CASE ··················· 5
2.
DISC REMOVAL PROCEDURE ······································ 5
3.
NOTE ON REMOVING THE TABLE ASS'Y ·················· 5
4.
NOTE ON MOUNTING THE GEARS ····························· 6
5.
HOW TO SERVICE THE MB-103 BOARD ····················· 7
6.
CONNECTION OF SERVICE JIG ···································· 9
1.
GENERAL
Precautions ············································································· 1-1
About this Manual ································································· 1-1
This Player Can Play the Following Discs ···························· 1-1
Notes about the Discs ···························································· 1-1
Index to Parts and Controls ···················································· 1-2
Guide to On-Screen Displays (Control Bar) ·························· 1-3
Simple Start Guide ···································································· 1-3
Quick Overview ····································································· 1-3
Step 1: Unpacking ································································· 1-3
Step 2: Inserting Batteries into the Remote ··························· 1-3
Step 3: TV Hookups ······························································ 1-3
Step 4: Playing a Disc ···························································· 1-4
Hookups ····················································································· 1-4
Hooking Up the Player ·························································· 1-4
Step 1: Connecting the Video Cords ······································ 1-4
Step 2: Connecting the Audio Cords ····································· 1-4
Step 3: Connecting the Power Cord ······································· 1-6
Step 4: Quick Setup ······························································· 1-6
Playing Discs ············································································· 1-6
Playing Discs ········································································· 1-6
Searching for a Particular Point on a Disc (Scan, Slow-motion
Play, Search, Freeze Frame) ··············································· 1-7
Resuming Playback from the Point Where You Stopped the
Disc (Resume Play/Multi-disc Resume) ····························· 1-7
Using the DVD's Menu ························································· 1-8
Playing VIDEO CDs with PBC Functions (PBC Playback) · 1-8
Playing an MP3 Audio Track ················································· 1-8
Various Play Mode Functions (Program Play, Shuffle Play,
Repeat Play, A-B Repeat Play) ··········································· 1-9
Searching for a Scene ······························································ 1-10
Searching for a Title/Chapter/Track/Index/Scene
(Search mode) ··································································· 1-10
Viewing Information About the Disc ······································· 1-10
Checking the Playing Time and Remaining Time ··············· 1-10
Sound Adjustments ·································································· 1-11
Changing the Sound ····························································· 1-11
TV Virtual Surround Settings (TVS) ··································· 1-11
Enjoying Movies ····································································· 1-12
Changing the Angles ···························································· 1-12
Displaying the Subtitles ······················································· 1-12
Adjusting the Picture Quality (BNR) ·································· 1-12
Adjusting the Playback Picture (CUSTOM PICTURE MODE) ·· 1-12
Enhancing the Playback Picture (DIGITAL VIDEO
ENHANCER) ··································································· 1-13
Using Various Additional Functions ········································ 1-13
Locking Discs (CUSTOM PARENTAL CONTROL,
PARENTAL CONTROL) ················································· 1-13
Controlling Your TV with the Supplied Remote ················· 1-14
Settings and Adjustments ························································ 1-15
Using the Setup Display ······················································ 1-15
Setting the Display or Sound Track Language
(LANGUAGE SETUP) ···················································· 1-15
Settings for the Display (SCREEN SETUP) ······················· 1-15
Custom Settings (CUSTOM SETUP) ································· 1-15
Settings for the Sound (AUDIO SETUP) ···························· 1-16
Additional Information ···························································· 1-16
Troubleshooting ··································································· 1-16
Self-diagnosis Function (When letters/numbers appear in
the display) ······································································· 1-17
Glossary ··············································································· 1-17
Language Code List ····························································· 1-18
2.
DISASSEMBLY
2-1.
DISASSEMBLY ······························································ 2-1
2-2.
UPPER CASE ································································· 2-1
2-3.
FRONT PANEL SECTION ············································· 2-2
2-4.
REAR PANEL ································································· 2-2
2-5.
MB-103 BOARD ····························································· 2-3
2-6.
CN-158 BOARD ····························································· 2-3
2-7.
AV-062 BOARD ······························································ 2-4
2-8.
ER-14 BOARD (AEP, UK) ············································· 2-4
2-9.
TABLE ASS'Y ································································ 2-4
2-10. LOADING MOTOR ASS'Y ··········································· 2-5
2-11. OPTICAL PICK-UP ························································ 2-5
2-12. POWER BLOCK ····························································· 2-6
2-13. IF-091 AND FR-187 BOARDS ······································ 2-6
2-14. INTERNAL VIEWS ························································ 2-7
2-15. CIRCUIT BOARDS LOCATION ··································· 2-8
3.
BLOCK DIAGRAMS
3-1.
OVERALL BLOCK DIAGRAM ···································· 3-1
3-2.
RF/SERVO BLOCK DIAGRAM ···································· 3-3
3-3.
SIGNAL PROCESSOR BLOCK DIAGRAM ················ 3-5
3-4.
SYSTEM CONTROL BLOCK DIAGRAM ··················· 3-7
3-5.
VIDEO BLOCK DIAGRAM (NC655P) ························· 3-9
3-6.
VIDEO BLOCK DIAGRAM (NC615) ························· 3-11
3-7.
AUDIO BLOCK DIAGRAM ········································ 3-13
3-8.
INTERFACE CONTROL BLOCK DIAGRAM ··········· 3-15
3-9.
POWER BLOCK DIAGRAM (1/2) ······························ 3-17
3-10. POWER BLOCK DIAGRAM (2/2) ······························ 3-19
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1.
FRAME SCHEMATIC DIAGRAM ································ 4-1
4-2.
PRINTED WIRING BOARDS AND SCHEMATIC
DIAGRAM ······································································ 4-4
WAVEFORMS ································································ 4-5
· MB-103(DVD/CD RF AMP, DIGITAL SERVO, MOTOR
DRIVE, SERVO, AV DECODER, SDRAM, SYSTEM
CONTROL, AUDIO DAC, PLL, I/P CONVERTER,
VIDEO ENCODER)
PRINTED WIRING BOARD ························· 4-7
· MB-103 (DVD/CD RF AMP, DIGITAL SERVO) (1/8)
SCHEMATIC DIAGRAM ···························· 4-11
· MB-103 (MOTOR DRIVE) (2/8)
SCHEMATIC DIAGRAM ···························· 4-13
· MB-103 (SERVO) (3/8)
SCHEMATIC DIAGRAM ···························· 4-15
· MB-103 (AV DECODER) (4/8)
SCHEMATIC DIAGRAM ···························· 4-17
· MB-103 (SDRAM) (5/8)
SCHEMATIC DIAGRAM ···························· 4-19
· MB-103 (SYSTEM CONTROL) (6/8)
SCHEMATIC DIAGRAM ···························· 4-21
· MB-103 (AUDIO DAC, PLL) (7/8)
SCHEMATIC DIAGRAM ···························· 4-23
· MB-103 (I/P CONVERTER, VIDEO ENCODER) (8/8)
SCHEMATIC DIAGRAM ···························· 4-25
· AV-062 (AUDIO OUT, VIDEO OUT)
PRINTED WIRING BOARD ······················· 4-29
· AV-062 (AUDIO OUT) (1/2)
SCHEMATIC DIAGRAM ···························· 4-31
· AV-062 (VIDEO OUT) (2/2)
SCHEMATIC DIAGRAM ···························· 4-33
· ER-14 (LINE1 OUT) (NC615:AEP,UK)
PRINTED WIRING BOARD ······················· 4-35
-- 4 --
· ER-14 (LINE1 OUT) (NC615:AEP,UK)
SCHEMATIC DIAGRAM ···························· 4-37
· IF-091 (IF COM), PL-031 (LED)
PRINTED WIRING BOARDS ····················· 4-39
· IF-091 (IF COM)
SCHEMATIC DIAGRAM ···························· 4-41
· FR-187 (FUNCTION SW/LED)
PRINTED WIRING BOARD ······················· 4-43
· FR-187 (FUNCTION SW/LED)
SCHEMATIC DIAGRAM ···························· 4-45
· CN-158 (CONNECTOR)
PRINTED WIRING BOARD ······················· 4-47
· CN-158 (CONNECTOR)
SCHEMATIC DIAGRAM ···························· 4-49
· SE-130 (SENSOR), MD-94 (MD INTERFACE)
PRINTED WIRING BOARD ······················· 4-51
· SE-130 (SENSOR), MD-94 (MD INTERFACE)
SCHEMATIC DIAGRAM ···························· 4-53
· HS10S1U, HS10S1F (SWITCHING REGULATOR)
PRINTED WIRING BOARDS ····················· 4-55
· HS10S1U, HS10S1F (SWITCHING REGULATOR)
SCHEMATIC DIAGRAM ···························· 4-57
5.
IC PIN FUNCTION DESCRIPTION
5-1.
SYSTEM CONTROL PIN FUNCTION
(MB-103 BOARD IC104: MB91307RPFV-G-BND-E1) · 5-1
6.
TEST MODE
6-1.
GENERAL DESCRIPTION ··········································· 6-1
6-2.
STARTING TEST MODE ··············································· 6-1
6-3.
SYSCON DIAGNOSIS ··················································· 6-1
6-4.
DRIVE AUTO ADJUSTMENT ······································ 6-5
6-5.
DRIVE MANUAL OPERATION ··································· 6-7
6-6.
MECHA AGING ··························································· 6-11
6-7.
EMERGENCY HISTORY ············································ 6-11
6-8.
VERSION INFORMATION ········································· 6-11
6-9.
VIDEO LEVEL ADJUSTMENT ·································· 6-11
6-10. IF CON SELF DIAGNOSTIC FUNCTION ················· 6-12
6-11. TROUBLESHOOTING ················································ 6-19
6-12. MECHANISM TEST MODE ADJUSTMENT ··········· 6-22
6-12-1. How to enter the mechanism test mode ······················ 6-22
6-12-2. Types of the mechanism test mode ····························· 6-22
6-12-3. Description of Each Mode ·········································· 6-22
7.
ELECTRICAL ADJUSTMENT
7-1.
POWER SUPPLY ADJUSTMENT ································· 7-1
1.
Power Supply Check (HS10S1U/HS10S1F Boards) ······ 7-1
7-2.
ADJUSTMENT OF VIDEO SYSTEM ··························· 7-2
1.
Video Level Adjustment (MB-103 Board) ······················ 7-2
2.
Progressive Video Output Level Adjustment
(MB-103 Board) ······························································ 7-2
3.
Checking S Video Output S-Y ········································· 7-2
4.
Checking S Video Output S-C ········································· 7-2
5.
Checking Component Video Output Y
(US, Canadian, Australian, PX Model) ··························· 7-3
6.
Checking Component Video Output B-Y
(US, Canadian, Australian, PX Model) ··························· 7-3
7.
Checking Component Video Output R-Y
(US, Canadian, Australian, PX Model) ··························· 7-3
8.
Checking RGB Output R (AEP, UK Model) ··················· 7-3
9.
Checking RGB Output G (AEP, UK Model) ·················· 7-4
10.
Checking RGB Output B (AEP, UK Model) ··················· 7-4
7-3.
ADJUSTMENT RELATED PARTS ARRANGEMENT ··· 7-5
8.
REPAIR PARTS LIST
8-1.
EXPLODED VIEWS ······················································ 8-1
8-1-1. OVERALL SECTION ····················································· 8-2
8-1-2. FRONT PANEL SECTION ············································· 8-3
8-1-3. LOADING SECTION ····················································· 8-4
8-1-4. CHASSIS SECTION ······················································· 8-5
8-2.
ELECTRICAL PARTS LIST ·········································· 8-6
-- 5 --
1.
NOTE ON REMOVING THE UPPER
CASE
1)
Remove the four tapping screws and three screws. (See Fig. 1)
2)
Open the sides of case. (See Fig. 1)
3)
Remove the upper case in the direction of the arrow A.
2.
DISC REMOVAL PROCEDURE
1)
Insert a flat-head (-) screwdriver into a hole at the bottom, and
rotate the cam gear in the direction of the arrow A. (See Fig.2)
Two tapping screws
Two tapping screws
Three screws (B3)
A
3.
NOTE ON REMOVING THE TABLE
ASS'Y
1)
Remove the two screws. (See Fig. 3)
A
Cam gear
Table
Hole
Screw
(M2.6
× 8)
Screw
(M2.6
× 8)
2)
Remove the two Plates (guide) in the direction of the arrows
A
and B.
3)
Remove the Table ass'y in the direction of the arrow C.
4)
Remove the Flexible flat cable (See Fig. 4).
A
B
C
Plate (guide)
Plate (guide)
Table ass'y
Flexible flat cable
(FMS-18: CN002)
Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.
SERVICE NOTE