SERVICE MANUAL
· INSTRUCTION MANUAL is shown at the end of this document.
Revision History
Revision History
Ver 1.0 2002. 09
LEVEL
1
Link
SELF DIAGNOSIS FUNCTION
ORNAMENTAL PARTS
SPECIFICATIONS
SELF DIAGNOSIS FUNCTION
ORNAMENTAL PARTS
SPECIFICATIONS
Link
US Model
Canadian Model
AEP Model
UK Model
E Model
Hong Kong Model
Australian Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
DIGITAL STILL CAMERA
DSC-F717
-- 2 --
DSC-F717
COVER
COVER
SPECIFICATIONS
System
Image device
11 mm (2/3 type) color CCD
Primary color filter
Total pixels number of camera
Approx. 5 240 000 pixels
Effective pixels number of camera
Approx. 5 020 000 pixels
Lens
5× zoom lens
f = 9.7 48.5 mm (13/32
1 15/16 inches) (38 190 mm
(1 1/2 7 1/2 inches) when converted
to a 35 mm still camera)
F2.0 2.4
Filter diameter: 58 mm (2 3/8 inches)
Exposure control
Automatic exposure, Shutter speed
priority, Aperture priority, Manual
exposure, Scene selection (4 modes)
White balance
Automatic, Daylight, Cloudy,
Fluorescent, Incandescent, One-push
Data format (DCF compliant)
Still images: Exif Ver. 2.2 JPEG
compliant, GIF (for Clip Motion),
TIFF, DPOF compatible
Audio with still image:
MPEG1 compliant (Monaural)
Moving images:
MPEG1 compliant (Monaural)
Recording media
"Memory Stick"
Flash
Recommended distance (ISO set to
Auto): 0.3 m to 4.5 m (11 7/8 inches
to 177 1/4 inches)
Accessories
· AC-L10A/L10B AC power adaptor
· Power cord (mains lead)
· USB cable
· NP-FM50 battery pack
· A/V connecting cable
·"Memory Stick" (32 MB)
· Shoulder strap
· Lens cap
· Lens cap strap
· CD-ROM (USB driver SPVD-008)
· Operating instructions
Design and specifications are subject to change
without notice.
Viewfinder
Electric viewfinder (color)
Input/Output connectors
A/V OUT (MONO) (Monaural)
Minijack
Video: 1 Vp-p, 75
, unbalanced,
sync negative
Audio: 327 mV (at a 47 k
load)
Output impedance 2.2 k
ACC jack Mini-minijack (ø 2.5 mm)
USB jack mini-B
LCD screen
Used LCD panel
4.6 cm (1.8 type) TFT drive
Total number of dots
123 200 (560×220) dots
General
Used battery pack
NP-FM50 (supplied)
Power requirements
7.2 V
Power consumption (during shooting)
2.3 W
Operating temperature
0°C to 40°C (32°F to 104°F)
Storage temperature
20°C to +60°C (4°F to +140°F)
Dimensions
119.5×68.9×151 mm
(4 3/4×2 3/4×6 inches)
(W/H/D, excluding maximum
protrusions)
Mass
Approx. 696 g (1 lb 8 oz) (including
battery pack NP-FM50, "Memory
Stick," shoulder strap and lens cap)
Built-in microphone
Electret condenser microphone
Built-in speaker
Dynamic speaker
AC-L10A/L10B AC power
adaptor
Power requirements
100 to 240 V AC, 50/60 Hz
Rated output voltage
DC 8.4 V, 1.5 A in operating mode
Operating temperature
0°C to 40°C (32°F to 104°F)
Storage temperature
20°C to +60°C (4°F to +140°F)
Dimensions
Approx. 125×39×62 mm
(5×1 9/16×2 1/2 inches) (w/h/d,
excluding maximum protrusions)
Mass
Approx. 280 g (10 oz)
NP-FM50 battery pack
Used battery
Lithium-ion battery
Maximum voltage
DC 8.4 V
Nominal voltage
DC 7.2 V
Capacity 8.5 Wh (1 180 mAh)
Operating temperature
0°C to 40°C (32°F to 104°F)
Dimensions
Approx. 38.2×20.5×55.6 mm
(1 9/16×13/16×2 1/4 inches) (w/h/d)
Mass
Approx. 76 g (3 oz)
-- 3 --
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
· Keep the temperature of the soldering iron around 270°C
during repairing.
· Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
· Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
DSC-F717
This statement is indicated under the lens.
CAUTION
Use of controls or adjustments or performance
procedures other than those specified herein may
result in hazardous radiation exposure.
-- 4 --
DSC-F717
SELF-DIAGNOSIS FUNCTION
COVER
COVER
[Description on Self-diagnosis Display]
Self-diagnosis display
· C: ss: ss
You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
· E: ss: ss
Contact your Sony dealer or local
authorized Sony service facility.
Display Code
C:32:ss
C:13:ss
Countermeasure
Turn the power off and on again.
Format the "Memory stick".
Insert a new "Memory Stick".
Cause
Trouble with hardware.
Unformatted memory stick is inserted.
Memory stick is broken.
Caution Display During Error
SYSTEM ERROR
FORMAT ERROR
MEMORY STICK ERROR
E:61:ss
E:91:ss
Checking of lens drive circuit.
When failed in the focus initialization.
Abnormality when flash is being
charged.
Checking of flash unit or replacement
of flash unit.
--
DSC-F717
-- 5 --
Note:
· Items marked "*" are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
· The parts numbers of such as a cabinet are also appeared in this section.
Refer to the parts number mentioned below the name of parts to order.
· Abbreviation
AUS: Australian model
CH : Chinese model
CND: Canadian model
1. ORNAMENTAL PARTS
COVER
COVER
HK : Hong Kong model
KR : Korean model
JE
: Tourist model
J
: Japanese model
Les composants identifiés par une
marque 0 sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
1. MAIN PARTS
CPC Lid
3-064-225-11
ACC Cap
3-071-262-01
(When change it, need to
dismantle the set.)
LCD Window
3-071-282-01
Adhesive Sheet (LCD)
3-071-283-01