US Model
Canadian Model
Korea Model
DCR-TRV19
AEP Model
East European Model
North European Model
DCR-TRV12E/TRV14E/TRV19E
UK Model
DCR-TRV14E/TRV19E
E Model
Hong Kong Model
DCR-TRV19/TRV19E
Australian Model
Chinese Model
DCR-TRV19E
SERVICE MANUAL
Z MECHANISM
LEVEL
2
· For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (987622441.pdf).
· For MECHANISM ADJUSTMENTS, refer to the "DV MECHANICAL ADJUSTMENT MANUAL
Z MECHANISM " (9-876-210-11).
Link
Link
Revision History
Revision History
Ver 1.0 2003. 02
On the VC-311 board
This service manual provides the information that is premised the circuit board replacement service and not intended repair
inside the VC-311 board.
Therefore, schematic diagram, printed wiring board, waveforms, mounted parts location and electrical parts list of the VC-311
board are not shown.
The following pages are not shown.
Schematic diagram ............................. Pages 4-37 to 4-52
Printed wiring board ............................ Pages 4-73 to 4-76
Waveforms ........................................... Page 4-79 to 4-80
Mounted parts location ............................. Page 4-83
Electrical parts list ................................... Pages 5-21 to 5-24
DCR-TRV12E/TRV14E/
TRV19/TRV19E
RMT-814
DIGITAL VIDEO CAMERA RECORDER
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
SPECIFICATIONS
REPAIR PARTS LIST
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SPECIFICATIONS
-- 2 --
DCR-TRV12E/TRV14E/TRV19/TRV19E
SPECIFICATIONS
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
COVER
COVER
CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Video camera
recorder
System
Video recording system
2 rotary heads
Helical scanning system
Audio recording system
Rotary heads, PCM system
Quantization: 12 bits (Fs 32 kHz,
stereo 1, stereo 2), 16 bits
DCR-TRV19:
NTSC colour, EIA standards
DCR-TRV12E/TRV14E/TRV19E:
(Fs 48 kHz, stereo)
Video signal
PAL colour, CCIR standards
Usable cassette
Mini DV cassette with the
mark printed
Tape speed
SP: Approx. 18.81 mm/s
LP: Approx. 12.56 mm/s
Recording/playback time
(using cassette DVM60)
SP: 1 hour
LP: 1.5 hours
Fastforward/rewind time
(using cassette DVM60)
Approx. 2 min. and 40 seconds
Viewfinder
Electric viewfinder
black and white
Image device
DCR-TRV12E/TRV14E/TRV19E:
4.5 mm (1/4 type)
CCD (Charge Coupled Device)
Gross:
DCR-TRV19:
DCR-TRV12E/TRV14E/TRV19E:
Effective (moving):
DCR-TRV19: Approx. 340 000 pixels
DCR-TRV12E/TRV14E/TRV19E:
Approx. 680 000 pixels
DCR-TRV19:
DCR-TRV12E/TRV14E/TRV19E:
0.3 Vp-p
0.286 Vp-p
Lens
Carl Zeiss Vario-Sonnar
Combined power zoom lens
Filter diameter: 30 mm
(1 3/16 in)
10
× (Optical), 120× (Digital)
Focal length
3.3 33 mm (5/32 1 5/16 in.)1)
42 420 mm (1 11/16 16 5/8
in.)2)
1) When converted to a 35 mm still
camera
2) In CAMERA mode
Colour temperature
Auto, HOLD, INDOOR (3 200 K),
OUTDOOR (5 800 K)
Minimum illumination
5 lx (lux) (F1.7)
0 lx (lux) (in the NightShot
mode)*
* Objects unable to be seen due to
the dark can be shot with
infrared lighting.
Input/Output connectors
S video output
4-pin mini DIN
(DCR-TRV19/TRV19E only)
Luminance signal: 1 Vp-p,
75
75
(ohms), unbalanced
Chrominance signal:
(ohms), unbalanced
Audio/Video output
AV MINI JACK, 1 Vp-p,
75
(ohms), unbalanced
327 mV, (at output impedance
more than 47 k
(kilohms))
Output impedance with less than
2.2 k
(kilohms)/Stereo minijack
(ø 3.5 mm)
Input impedance more than
47 k
(kilohms)
DV input (DCR-TRV19/TRV19E
only)/output
4-pin connector
Headphone jack
Stereo minijack (ø 3.5 mm)
LANC jack
Stereo mini-minijack (ø 2.5 mm)
USB jack
mini-B
MIC jack
Minijack, 0.388 mV low impedance
with 2.5 to 3.0 V DC, output
impedance 6.8 k
(kilohms)
(ø 3.5 mm)
Stereo type
LCD screen
Picture
6.2 cm (2.5 type)
50.3
× 37.4 mm (2 × 1 1/2 in.)
Total dot number
123 200 (560
× 220)
General
Power requirements
7.2 V (battery pack)
8.4 V (AC Adaptor)
Average power consumption
(when using the battery pack)
3.3 W1)
2.5 W2)
1) During camera recording using
LCD
2) Viewfinder
Operating temperature
0
°C to 40°C (32°F to 104°F)
Storage temperature
20
°C to + 60°C
(4
°F to + 140°F)
Dimensions (approx.)
71
× 90 × 112 mm
(2 7/8
× 3 5/8 × 4 1/2 in.) (w/h/d)
Mass (approx.)
Main unit only
520 g (1 lb 2 oz)
Including the rechargeable battery
pack NP-FM30, cassette DVM60
and lens cap
610 g (1 lb 5 oz)
Supplied accessories
See page 3.
AC Adaptor
AC-L15A/L15B
Power requirements
100 240 V AC, 50/60 Hz
Current consumption
0.35 0.18 A
Power consumption
18 W
Output voltage
DC OUT: 8.4 V, 1.5 A
Operating temperature
0
°C to 40°C (32°F to 104°F)
Storage temperature
20
°C to + 60°C
(4
°F to + 140°F)
Dimensions (approx.)
56
× 31 × 100 mm
(2 1/4
× 1 1/4 × 4 in.) (w/h/d)
excluding projecting parts
Mass (approx.)
190 g (6.7 oz)
excluding power cord
Rechargeable
battery pack
NP-FM30
Maximum output voltage
DC 8.4 V
Output voltage
DC 7.2 V
Capacity
5.0 Wh (700 mAh)
Dimensions (approx.)
38.2
× 20.5 × 55.6 mm
(1 9/16
× 13/16 × 2 1/4 in.)
(w/h/d)
Mass (approx.)
65 g (2.3 oz)
Operating temperature
0
°C to 40°C (32°F to 104°F)
Type
Lithium ion
Design and specifications are
subject to change without notice.
-- 3 --
DCR-TRV12E/TRV14E/TRV19/TRV19E
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
· Keep the temperature of the soldering iron around 270°C
during repairing.
· Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
· Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
· Unleaded solder melts at a temperature about 40
°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
· Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
· Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
· SUPPLIED ACCESSORIES
Make sure that the following accessories are supplied with your camcorder.
1
AC-L15A/L15B AC Adaptor (1), Power
cord (1)
2
NP-FM30 rechargeable battery pack
(1)
3
A/V connecting cable (1)
4
Wireless Remote Commander
RMT-814E (EXCEPT TRV12E)
(1)
5
R6 (size AA) battery for Remote
Commander (2)
6
Shoulder strap (1)
7
Lens cap (1)
8
Shoe cover (1)
9
USB cable (1)
q;
CD-ROM (USB Driver)
SPVD-010 (I), US, CND model only
SPVD-010
EXCEPT US, CND model only
(1)
qa
Cleaning cloth (1)
qs
21-pin adaptor* (1) (AEP, UK, EE, NE model only)
The models with
mark printed on their
bottom surfaces only.
9
1
4
q;
5
qa
6
2
7
3
8
qs
qd
qd
2-pin conversion adaptor (1)
(E, HK only)
*
· Abbreviation
CND : Canadian model
EE
: East European model
NE
: North European model
HK
: Hong Kong model
-- 4 --
DCR-TRV12E/TRV14E/TRV19/TRV19E
TABLE OF CONTENTS
1.
SERVICE NOTE
1-1.
SERVICE NOTE ····························································· 1-1
1.
POWER SUPPLY DURING REPAIRS ·························· 1-1
2.
TO TAKE OUT A CASSETTE WHEN NOT EJECT
(FORCE EJECT) ····························································· 1-1
1-2.
SELF-DIAGNOSIS FUNCTION ···································· 1-2
1.
SELF-DIAGNOSIS FUNCTION ···································· 1-2
2.
SELF-DIAGNOSIS DISPLAY ······································· 1-2
3.
SELF-DIAGNOSIS CODE TABLE ································ 1-3
2.
DISASSEMBLY
2-1.
P CABINET (C) ASSEMBLY ········································ 2-3
2-2.
CABINET (R) COVER (39E) ASSEMBLY ··················· 2-4
2-3.
F PANEL SECTION ······················································· 2-5
2-4.
MA-421 BOARD ···························································· 2-6
2-5.
CABINET (R) SECTION ··············································· 2-7
2-6.
LCD SECTION ······························································· 2-8
2-7.
CK-129 BOARD,
CONTROL SWITCH BLOCK(CF-CX4000) ················· 2-8
2-8.
PD-188 BOARD, LCD UNIT ········································· 2-9
2-9.
HINGE (40) ASSEMBLY ············································· 2-10
2-10. BT PANEL/EVF SECTION ·········································· 2-11
2-11. LB-085 BOARD (REMOVING OF THE EVF)-1 ········ 2-12
2-12. LB-085 BOARD (REMOVING OF THE EVF)-2 ········ 2-13
2-13. LB-085 BOARD (REMOVING OF THE EVF)-3 ········ 2-14
2-14. VA-118 BOARD, LENS SECTION ······························ 2-15
2-15. CD-430 BOARD ··························································· 2-16
2-16. MECHANISM DECK, VC-312 BOARD (1) ··············· 2-16
2-17. MECHANISM DECK, VC-312 BOARD (2) ··············· 2-17
2-18. CABINET (G) ASSEMBLY (40E) ······························· 2-17
2-19. CONTROL SWITCH BLOCK (FK-CX4000) ·············· 2-18
2-20. JK-242 BOARD ···························································· 2-18
2-21. CIRCUIT BOARDS LOCATION ································· 2-20
2-22. FLEXIBLE BOARDS LOCATION ······························ 2-21
3.
BLOCK DIAGRAMS
3-1.
OVERALL BLOCK DIAGRAM (1/4) ··························· 3-1
3-2.
OVERALL BLOCK DIAGRAM (2/4) ··························· 3-3
3-3.
OVERALL BLOCK DIAGRAM (3/4) ··························· 3-5
3-4.
OVERALL BLOCK DIAGRAM (4/4) ··························· 3-7
3-5.
POWER BLOCK DIAGRAM (1/2) ································ 3-9
3-6.
POWER BLOCK DIAGRAM (2/2) ······························ 3-11
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1.
FRAME SCHEMATIC DIAGRAM (1/3) ······················· 4-1
FRAME SCHEMATIC DIAGRAM (2/3) ······················· 4-3
FRAME SCHEMATIC DIAGRAM (3/3) ······················· 4-5
4-2.
SCHEMATIC DIAGRAMS
· CD-430 (CCD IMAGER)
SCHEMATIC DIAGRAM ······························ 4-9
· LB-085 (EVF, BACK LIGHT)
SCHEMATIC DIAGRAM ···························· 4-10
· VA-118 (1/5)(RGB DRIVE, TG)
SCHEMATIC DIAGRAM ···························· 4-11
· VA-118 (2/5)(HI CONTROL)
SCHEMATIC DIAGRAM ···························· 4-13
· VA-118 (3/5)(Y/P SENSOR AMP, CONNECTOR)
SCHEMATIC DIAGRAM ···························· 4-15
· VA-118 (4/5)(DC/DC COVERTER)
SCHEMATIC DIAGRAM ···························· 4-17
· VA-118 (5/5)(POWER IN, CHARGE)
SCHEMATIC DIAGRAM ···························· 4-19
· CK-129 (FUNCTION SWITCH)
SCHEMATIC DIAGRAM ···························· 4-21
· PD-188 (1/2)(DRIVER, TG)
SCHEMATIC DIAGRAM ···························· 4-23
· PD-188 (2/2)(BACKLIGHT DRIVE)
SCHEMATIC DIAGRAM ···························· 4-25
· JK-242 (A.V/DV IN/OUT)
SCHEMATIC DIAGRAM ···························· 4-27
· CONTROL SWITCH BLOCK (FK-CX4000)
SCHEMATIC DIAGRAM ···························· 4-29
· MA-421 (1/2)(MIC AMP)
SCHEMATIC DIAGRAM ···························· 4-31
· MA-421 (2/2)(Y/P SENSOR, V/A IN/OUT)
SCHEMATIC DIAGRAM ···························· 4-33
· FP-467/468/228 FLEXIBLE (S/T REEL SENSOR,
TAPE SENSOR)
SCHEMATIC DIAGRAM ···························· 4-35
Shematic diagram of the VC-311 board are not shown.
Pages from 4-37 to 4-52 are not shown.
4-3.
PRINTED WIRING BOARDS
· CD-430 (CCD IMAGER)
PRINTED WIRING BOARD ······················· 4-55
· LB-085 (EVF, BACK LIGHT)
PRINTED WIRING BOARD ······················· 4-57
· FP-467/468/228 FLEXIBLE BOARD
(S/T REEL SENSOR, TAPE SENSOR) ····················· 4-59
· FP-626 FLEXIBLE BOARD ····································· 4-59
· VA-118 (RGB DRIVE, TG, HI CONTROL, Y/P
SENSOR AMP, CONNECTOR, DC/DC COVERTER,
POWER IN, CHARGE)
PRINTED WIRING BOARD ······················· 4-61
· CK-129 (FUNCTION SWITCH)
PRINTED WIRING BOARD ······················· 4-65
· PD-188 (DRIVER, TG, BACKLIGHT DRIVE)
PRINTED WIRING BOARD ······················· 4-67
· JK-242 (A.V/DV IN/OUT)
PRINTED WIRING BOARD ······················· 4-69
· MA-421 (MIC AMP, Y/P SENSOR, V/A IN/OUT)
PRINTED WIRING BOARD ······················· 4-71
Printed wiring board of the VC-311 board are not shown.
Pages from 4-73 to 4-76 are not shown.
4-4.
WAVEFORMS ······························································ 4-77
Waveforms of the VC-311 board are not shown.
Pages 4-79 and 4-80 are not shown.
4-5.
MOUNTED PARTS LOCATION ································· 4-81
Mounted parts location of the VC-311 board is not shown.
Page 4-83 is not shown.
5.
REPAIR PARTS LIST
5-1.
EXPLODED VIEWS ······················································ 5-1
5-1-1. OVERALL SECTION ····················································· 5-3
5-1-2. F PANEL SECTION ······················································· 5-4
5-1-3. MAIN CHASSIS SECTION ··········································· 5-5
5-1-4. LENS SECTION ····························································· 5-6
5-1-5. CABINET L SECTION ·················································· 5-7
5-1-6. BT PANEL/EVF SECTION ············································ 5-8
5-1-7. CABINET R SECTION ·················································· 5-9
5-1-8. LCD SECTION ····························································· 5-10
5-1-9. OVERALL (MECHANISM DECK-Z100) ··················· 5-11
5-1-10. LS CHASSIS BLOCK ASSEMBLY ························· 5-12
5-1-11. MECHANICAL CHASSIS BLOCK ASSEMBLY ··· 5-13
-- 5 --
DCR-TRV12E/TRV14E/TRV19/TRV19E
5-2.
ELECTRICAL PARTS LIST ········································ 5-14
Parts list of the VC-311 board are not shown.
Pages from 5-21 to 5-24 are not shown.