SONY CPD-E210 - Owner's Manual Immediate Download

4-077-098-11 (1)

Trinitron Color

Computer Display

Operating Instructions

D:\###sagyou\02 gatu\0203-ya\874120S CPD-E210\01US01COV-UC.fm

masterpage:Right

CPD-E210

4-077-098-11 (1)

CPD-E210

01US01COV-UC.book Page 1 Thursday, February 3, 2000 4:06 PM

Owner's Record

The model and serial numbers are located at the rear of the unit.

Record these numbers in the spaces provided below. Refer to them

whenever you call upon your dealer regarding this product.

Model No.

Serial No.

To prevent fire or shock hazard, do not expose the

unit to rain or moisture.

Dangerously high voltages are present inside the

unit. Do not open the cabinet. Refer servicing to

qualified personnel only.

FCC Notice

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for

help.

You are cautioned that any changes or modifications not expressly

approved in this manual could void your authority to operate this

equipment.

INFORMATION

This product complies with Swedish National Council for Metrology

(MPR) standards issued in December 1990 (MPR II) for very low

frequency (VLF) and extremely low frequency (ELF).

If you have any questions about this product, you may call:

Sony Customer Information Center

1-800-222-SONY (7669)

or write to:

Sony Customer Information Center

1 Sony Drive, Mail Drop #T1-11, Park Ridge, NJ 07656

WARNING

NOTICE

This notice is applicable for USA/Canada only.

If shipped to USA/Canada, install only a UL LISTED/CSA

LABELLED power supply cord meeting the following

specifications:

SPECIFICATIONS

Plug Type

Nema-Plug 5-15p

Cord

Type SVT or SJT, minimum 3

× 18 AWG

Length

Maximum 15 feet

Rating

Minimum 7 A, 125 V

NOTICE

Cette notice s'applique aux Etats-Unis et au Canada

uniquement.

Si cet appareil est export* aux Etats-Unis ou au Canada, utiliser

le cordon d'alimentation portant la mention UL LISTED/CSA

LABELLED et remplissant les conditions suivantes:

SPECIFICATIONS

Type de fiche

Fiche Nema 5-15 broches

Cordon

Type SVT ou SJT, minimum 3

× 18 AWG

Longueur

Maximum 15 pieds

Tension

Minimum 7 A, 125 V

As an

ENERGY STAR Partner, Sony

Corporation has determined that this

product meets the

ENERGY STAR

guidelines for energy efficiency.

Declaration of Conformity

Trade Name:

Sony

Model No.:

CPD-E210

Responsible Party:

Sony Electronics Inc.

Address:

1 Sony Drive, Park Ridge, NJ 07656 USA

Telephone No.:

201-930-6970

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

Table of Contents

· Trinitron® and FD Trinitron® is a

registered trademark of Sony

Corporation.

· Macintosh is a trademark licensed to

Apple Computer, Inc., registered in the

U.S.A. and other countries.

· Windows® and MS-DOS are registered

trademarks of Microsoft Corporation in

the United States and other countries.

· IBM PC/AT and VGA are registered

trademarks of IBM Corporation of the

U.S.A.

· VESA and DDCTM are trademarks of the

Video Electronics Standard Association.

ENERGY STAR is a U.S. registered

mark.

· All other product names mentioned

herein may be the trademarks or

registered trademarks of their respective

companies.

· Furthermore, "

TM" and "®" are not

mentioned in each case in this manual.

D:\###sagyou\02 gatu\0203-ya\874120S CPD-E210\01US01COV-UCTOC.fm

masterpage:Toc.master

CPD-E210

4-077-098-11 (1)

Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Identifying parts and controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Step 1: Connect your monitor to your computer . . . . . . . . . . . . . . . 6

Step 2: Connect the power cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Step 3: Turn on the monitor and computer . . . . . . . . . . . . . . . . . . . 7

Selecting the on-screen menu language (LANG) . . . . . . . . . . . . . . . 7

Customizing Your Monitor . . . . . . . . . . . . . . . . . . . . . . . .8

Navigating the menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Adjusting the brightness and contrast. . . . . . . . . . . . . . . . . . . . . . . . 9

Adjusting the centering of the picture (CENTER) . . . . . . . . . . . . . . . 9

Adjusting the size of the picture (SIZE) . . . . . . . . . . . . . . . . . . . . . . 9

Enlarging or reducing the picture (ZOOM) . . . . . . . . . . . . . . . . . . . 10

Adjusting the shape of the picture (GEOM) . . . . . . . . . . . . . . . . . . 10

Adjusting the color of the picture (COLOR) . . . . . . . . . . . . . . . . . . 10

Adjusting the convergence (CONV) . . . . . . . . . . . . . . . . . . . . . . . . 10

Additional settings (OPTION) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Helpful hints and information (HELP) . . . . . . . . . . . . . . . . . . . . . . . 12

Resetting the adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Technical Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Preset and user modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Power saving function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

If thin lines appear on your screen (damper wires). . . . . . . . . . . . . 13

On-screen messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Trouble symptoms and remedies . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Self-diagnosis function . . . . . . . . . . . . . . . . . . . . . . . . . . . Back cover

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . Back cover

01US01COV-UC.book Page 3 Thursday, February 3, 2000 4:06 PM

D:\###sagyou\02 gatu\0203-ya\874120S CPD-E210\01US03BAS-UC.fm

masterpage:Left

CPD-E210

4-077-098-11 (1)

Precautions

Warning on power connections

· Use the supplied power cord. If you use a different power cord,

be sure that it is compatible with your local power supply.

For the customers in the U.S.A.

If you do not use the appropriate cord, this monitor will not

conform to mandatory FCC standards.

· Before disconnecting the power cord, wait at least 30 seconds

after turning off the power to allow the static electricity on the

screen's surface to discharge.

· After the power is turned on, the screen is demagnetized

(degaussed) for about 5 seconds. This generates a strong

magnetic field around the screen which may affect data stored

on magnetic tapes and disks placed near the monitor. Be sure to

keep magnetic recording equipment, tapes, and disks away

from the monitor.

Installation

Do not install the monitor in the following places:

· on surfaces (rugs, blankets, etc.) or near materials (curtains,

draperies, etc.) that may block the ventilation holes

· near heat sources such as radiators or air ducts, or in a place

subject to direct sunlight

· in a place subject to severe temperature changes

· in a place subject to mechanical vibration or shock

· on an unstable surface

· near equipment which generates magnetism, such as a

transformer or high voltage power lines

· near or on an electrically charged metal surface

Maintenance

· Clean the screen with a soft cloth. If you use a glass cleaning

liquid, do not use any type of cleaner containing an anti-static

solution or similar additive as this may scratch the screen's

coating.

· Do not rub, touch, or tap the surface of the screen with sharp or

abrasive items such as a ballpoint pen or screwdriver. This type

of contact may result in a scratched picture tube.

· Clean the cabinet, panel and controls with a soft cloth lightly

moistened with a mild detergent solution. Do not use any type

of abrasive pad, scouring powder or solvent, such as alcohol or

benzene.

Transportation

When you transport this monitor for repair or shipment, use the

original carton and packing materials.

Use of the tilt-swivel

This monitor can be adjusted within the angles shown below. To

find the center of the monitor's turning radius, align the center of

the monitor's screen with the centering dots on the stand.

Hold the monitor at the bottom with both hands when you turn it

horizontally or vertically. Be careful not to pinch your fingers at

the back of the monitor when you tilt the monitor up vertically.

The equipment should be installed near an easily accessible

outlet.

Example of plug types

for 100 to 120 V AC

for 200 to 240 V AC

90°

5°

90°

15°

Centering dots

01US01COV-UC.book Page 4 Thursday, February 3, 2000 4:06 PM

D:\###sagyou\02 gatu\0203-ya\874120S CPD-E210\01US03BAS-UC.fm

masterpage:Right

CPD-E210

4-077-098-11 (1)

Identifying parts and controls

See the pages in parentheses for further details.

1 RESET button (page 12)

This button resets the adjustments to the factory settings.

2 Control button (page 9)

The control button is used to display the menu and make

adjustments to the monitor, including brightness and contrast

adjustments.

3 1 (power) switch and indicator (pages 7, 13 and

back cover)

This button turns the monitor on and off. The power indicator

lights up in green when the monitor is turned on, and either

flashes in green and orange, or lights up in orange when the

monitor is in power saving mode.

4 AC IN connector (page 6)

This connector provides AC power to the monitor.

5 Video input connector (HD15) (page 6)

This connector inputs RGB video signals (0.700 Vp-p,

positive) and sync signals.

* DDC (Display Data Channel) is a standard of VESA.

AC IN

RESET

Rear

Front

Pin No.

Signal

1Red

Green

(Sync on Green)

3Blue

ID (Ground)

DDC Ground*

Red Ground

Green Ground

Blue Ground

Ground

ID (Ground)

Bi-Directional Data (SDA)*

H. Sync

V. Sync

Data Clock (SCL)*

1 2

3 4 5

11 12 13 14 15

01US01COV-UC.book Page 5 Thursday, February 3, 2000 4:06 PM