1
CD
Model Name Using Similar Mechanism CFD-S32
Section
CD Mechanism Type
KSM-213CDP
Optical Pick-up Name
KSS-213C
TC
Model Name Using Similar Mechanism CFD-V5
Section Tape Transport Mechanism Type
MF-V5-117
SERVICE MANUAL
US Model
CFD-S36
CD RADIO CASSETTE-CORDER
Other Specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6
µW
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 - 20,000 Hz +1/2 dB
Wow and flutter
Below measurable limit
SPECIFICATIONS
Continued on next page
Radio section
Frequency range
FM: 87.6 - 108 MHz
AM: 530 - 1,710 kHz
TV: 2 - 13 CH
WEATHER: 1 - 7 CH
Antennas
FM/TV/WEATHER: Telescopic antennas
AM: Built-in ferrite bar antennas
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 120 sec. with Sony cassette C-60
Frequency response
TYPE I (normal): 80 - 10,000 Hz
General
Speaker
Full range: 10 cm dia.,
3.2 ohms, cone type (2)
Outputs
Headphones jack (stereo minijack)
For 16 - 68 ohms impedance headphones
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
With 3.2-ohm loads, both channels driven from
150 - 6,300 Hz; rated 1.8 W per channel-
minimum RMS power, with no more than 10%
total harmonic distortion in AC operation.
Photo: White
Ver. 1.3 2005.09
Sony Corporation
Personal Audio Group
Published by Sony Engineering Corporation
9-873-061-14
2005I04-1
© 2005.09
2
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
Power output
2.3 W + 2.3 W (at 3.2 ohms, 10 %
harmonic distortion in AC operation)
Power requirements
For CD radio cassette-corder:
120 V AC, 60 Hz
9 V DC, 6 size D (R20) batteries
For remote control
3 V DC, 2 size AA (R6) batteries
Power consumption
AC 20 W
Battery life
For CD radio cassette-corder:
FM recording
Sony R20P: approx. 13.5 h
Sony alkaline LR20: approx. 20 h
Tape playback
Sony R20P: approx. 7.5 h
Sony alkaline LR20: approx. 15 h
CD playback
Sony R20P: approx. 2.5 h
Sony alkaline LR20: approx. 7 h
Dimensions
Approx. 420
× 159 × 284 mm (w/h/d)
(16 5/8
× 6 3/8 × 11 1/4 inches) (incl. projecting parts)
Mass
Approx. 3.8 kg (8 lb. 6 oz.) (incl. batteries)
Supplied accessories
AC power cord (1)
Remote control RMT-CS36WA (1)
Design and specifications are subject to change without
notice.
CAUTION
Use of controls or adjustments or performance of proce-
dures other than those specified herein may result in haz-
ardous radiation exposure.
Flexible Circuit Board Repairing
· Keep the temperature of the soldering iron around 270°C during
repairing.
· Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
· Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on Chip Component Replacement
· Never reuse a disconnected chip component.
· Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
CFD-S36
3
TABLE OF CONTENTS
1. SERVICING NOTES ......................................................... 4
2. GENERAL
Location of controls ................................................................. 5
3. DISASSEMBLY
3-1. Cabinet (Front) Sub Assy .................................................... 6
3-2. Wires ................................................................................... 7
3-3. Power (1) Board, Power (2) Board ...................................... 7
3-4. Cabinet (Upper) Assy .......................................................... 8
3-5. Main Board ......................................................................... 8
3-6. CD Mechanism Block ......................................................... 9
3-7. Tape Mechanism Block ....................................................... 9
3-8. Holder Assy, Cassette ........................................................ 10
3-9. PRE Board ......................................................................... 10
3-10. Belt, M801 (Capstan/Reel Moter),
HRP301 (Head, Magnetic) ................................................ 11
3-11. Optical Pick-up ................................................................. 11
4. MECHANICAL ADJUSTMENTS ............................... 12
5. ELECTRICAL ADJUSTMENTS
Tape Section .......................................................................... 12
Tuner Section ......................................................................... 13
CD Section ............................................................................ 14
6. DIAGRAMS
6-1. IC Pin Description ............................................................. 15
6-2. Circuit Boards Location .................................................... 15
6-3. Block Diagram CD Section ......................................... 16
6-4. Block Diagram Main Section ...................................... 17
6-5. Printed Wiring Board CD Section ............................... 18
6-6. Schematic Diagram CD Section .................................. 19
6-7. Printed Wiring Boards Main Section .......................... 20
6-8. Schematic Diagram Main Section (1/4) ...................... 21
6-9. Schematic Diagram Main Section (2/4) ...................... 22
6-10. Schematic Diagram Main Section (3/4) ...................... 23
6-11. Schematic Diagram Main Section (4/4) ...................... 24
6-12. Printed Wiring Boards Control Section ....................... 25
6-13. Schematic Diagrams Control Section ......................... 26
6-14. Printed Wiring Boards Power Supply Section ............ 27
6-15. Schematic Diagrams Power Supply Section ............... 28
7. EXPLODED VIEWS
7-1. Cabinet (Front) Section ..................................................... 32
7-2. Cabinet (Rear) Section ...................................................... 33
7-3. Cabinet (Upper) Section .................................................... 34
7-4. Tape Mechanism Section-1 ............................................... 35
7-5. Tape Mechanism Section-2 ............................................... 36
7-6. Optical Pick-up Section .................................................... 37
8. ELECTRICAL PARTS LIST ......................................... 38
To Exposed Metal
Parts on Set
0.15µF
1.5k
AC
voltmeter
(0.75V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, "metallized" knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers' instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The "limit" indication is 0.75
V, so analog meters must have an accurate low-voltage scale. The
Simpson 250 and Sanwa SH-63Trd are examples of a passive
VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A)
CFD-S36
4
CFD-S36
CHUCK PLATE JIG ON REPAIRING
On repairing CD section, playing a disc without the lid (CD), use
Chuck Plate Jig.
· Code number of Chuck Plate Jig: X-4918-255-1
SECTION 1
SERVICING NOTES
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
1. Turn ON the POWER button and press FUNCTION button to
CD position.
2. Open the lid (CD).
3. Turn on S801 with screwdriver, etc. as following figure.
4. Press the CD N X button.
5. Confirm the laser diode emission while observing the objecting
lens. When there is no emission, Auto Power Control circuit or
Optical Pick-up is broken.
Objective lens moves up and down three times for focus search.
S801
5
CFD-S36
SECTION 2
GENERAL
This section is extracted
from instruction manual.
REC
PLAY
REW
FF
STOP/EJECT PAUSE
VOLUME +,
MEGA Xpand
(CFD-S36 only)
MEGA BASS
Z
PUSH
OPEN/CLOSE
CD
compartment
Number buttons for
CD/RADIO DIRECT OPERATION
Tape
compartment
POWER
SLEEP
N X
x
CD
TAPE
RADIO BAND
AUTO PRESET
WEATHER
(CFD-S36 US model only)
Remote sensor
(CFD-S36 only)
Display
OPR/BATT
indicator
MODE
i
(headphones) jack
DISPLAY ENT
MEMORY
TUNE , +
.
,>
Remote Control (CFD-S36 only)
Location of controls
SLEEP
FUNCTION
Number buttons
MODE
TUNE +,
BAND
WEATHER
(US model only)
N
MEGA Xpand
POWER
VOL +,
x
X
MEGA BASS
.
,>
Tip
To listen through headphones, connect the headphones to the i (headphones) jack.