SONY CFD-S36 - Owner's Manual Immediate Download

Specifications

AUDIO POWER SPECIFICATIONS

POWER OUTPUT AND TOTAL

HARMONIC DISTORTION

With 3.2-ohm loads, both channels

driven from 150 - 6,300 Hz; rated

1.8 W per channel-minimum RMS

power, with no more than 10 % total

harmonic distortion in AC operation.

Other Specifications

CD player section

System

Compact disc digital audio system

Laser diode properties

Material: GaAlAs

Wave length: 780 nm

Emission duration: Continuous

Laser output: Less than 44.6 µW

(This output is the value measured at a

distance of about 200 mm from the

objective lens surface on the optical

pick-up block with 7 mm aperture.)

Spindle speed

200 r/min (rpm) to 500 r/min (rpm)

(CLV)

Number of channels

Frequency response

20 - 20,000 Hz +1/2 dB

Wow and flutter

Below measurable limit

Radio section

Frequency range

FM: 87.6 - 108 MHz

AM: 530 - 1,710 kHz

TV: 2 - 13 CH (CFD-S36 USA model

only)

WEATHER: 1 - 7 CH (CFD-S36 USA

model only)

Antennas

FM/TV/WEATHER: Telescopic

antenna

AM: Built-in ferrite bar antenna

Cassette-corder section

Recording system

4-track 2 channel stereo

Fast winding time

Approx. 120 s (sec.) with Sony cassette

C-60

Frequency response

TYPE I (normal): 80 - 10,000 Hz

General

Speaker

Full range: 10 cm dia., 3.2 ohms, cone

type (2)

Outputs

Headphones jack (stereo minijack)

For 16 - 68 ohms impedance

headphones

Power output (excluding USA model)

2.3 W + 2.3 W (at 3.2 ohms, 10 %

harmonic distortion in AC operation)

Power requirements

For CD radio cassette-corder:

120 V AC, 60 Hz

9 V DC, 6 size D (R20) batteries

For remote control (CFD-S36 only):

3 V DC, 2 size AA (R6) batteries

Power consumption

AC 20 W

Battery life

For CD radio cassette-corder:

FM recording

Sony R20P: approx. 13.5 h

Sony alkaline LR20: approx. 20 h

Tape playback

Sony R20P: approx. 7.5 h

Sony alkaline LR20: approx. 15 h

CD playback

Sony R20P: approx. 2.5 h

Sony alkaline LR20: approx. 7 h

Dimensions

Approx. 420

× 159 × 284 mm (w/h/d)

(16 5/8

× 6 3/8 × 11 1/4 inches) (incl.

projecting parts)

Mass

Approx. 3.8 kg (8 lb. 6 oz) (incl.

batteries)

Tape Player

The tape does not move when you

press an operation button.

· Close the cassette compartment

securely.

The REC z button does not

function or the tape does not play

or record.

· Make sure the safety tab on the

cassette is in place.

Poor or distorted playback,

recording or erasing quality.

· Clean the heads, pinch roller and

capstan with a cleaning swab

slightly moistened with cleaning

fluid or alcohol.

· Replace all the batteries with new

ones if they are weak.

· TYPE II (high position) or TYPE

IV (metal) tape is being used. Use

TYPE I (normal) tape only.

· Demagnetize the heads using a

commercially available tape head

demagnetizer.

Remote (CFD-S36 only)

The remote does not function.

· Replace all the batteries in the

remote with new ones if they are

weak.

· Make sure that you are pointing

the remote at the remote sensor on

the player.

· Remove any obstacles in the path

of the remote and the player.

· Make sure the remote sensor is

not exposed to strong light such

as direct sunlight or fluorescent

lamp light.

· Move closer to the player when

using the remote.

After trying the above remedies, if

you still have problems, unplug the

AC power cord and remove all the

batteries. After all the indications in

the display disappear, plug the power

cord and insert the batteries again. If

the problem persists, please consult

your nearest Sony dealer.

Printed in China

Operating Instructions

CD Radio

Cassette-

Corder

3-227-155-14(1)

WARNING

To prevent fire or shock

hazard, do not expose the

player to rain or moisture.

This symbol is intended to

alert the user to the

presence of uninsulated

"dangerous voltage" within

the product's enclosure that

may be of sufficient

magnitude to constitute a

risk of electric shock to

persons.

This symbol is intended to

alert the user to the

presence of important

operating and maintenance

(servicing) instructions in

the literature accompanying

the appliance.

CAUTION

The use of optical instruments with

this product will increase eye hazard.

WARNING

Do not install the appliance in a

confined space, such as a bookcase or

built-in cabinet.

For customers in Canada

To prevent electric shock, match wide

blade of plug to wide slot, fully insert.

Information

For customers in the United States

This equipment has been tested and

found to comply with the limits for a

Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits

are designed to provide reasonable

protection against harmful

interference in a residential

installation. This equipment

generates, uses and can radiate radio

frequency energy and, if not installed

and used in accordance with the

instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that

interference will not occur in a

particular installation. If this

equipment does cause harmful

interference to radio or television

reception, which can be determined

by turning the equipment off and on,

the user is encouraged to try to correct

the interference by one or more of the

following measures:

-- Reorient or relocate the receiving

antenna.

-- Increase the separation between the

equipment and receiver.

-- Connect the equipment into an

outlet on a circuit different from

that to which the receiver is

connected.

-- Consult the dealer or an

experienced radio/TV technician

for help.

You are cautioned that any changes or

modifications not expressly approved

in this manual could void your

authority to operate this equipment.

If you have any questions about this

product, you may call: Sony Direct

Response Center 1-(800)-222-7669

CFD-S26

CFD-S36

1 Press TAPE (direct power-on).

2 Press xZ to open the tape compartment and insert a

recorded tape. Close the compartment.

3 Press N.

With the side you want to

play facing upward

2 Select the program source you want to record.

To record from the CD player

Press CD and insert a CD (See "Playing a CD").

To record from the radio

Press RADIO BAND·AUTO PRESET and tune in the

station you want (See "Listening to the radio").

3 Press z to start recording.

(N is depressed automatically).

1 Press xZ to open the tape compartment and insert a

blank tape.

With the side you want to

record on facing upward

stop recording

pause recording

turn on/off the player

POWER

Tips

· Adjusting the volume or the audio emphasis will not affect the

recording level.

· For the best results, use the AC power as a power source for recording.

· To erase a recording, proceed as follows:

1 Insert a tape with the recording you want to erase.

2 Press TAPE.

3 Press z.

adjust the volume

stop playback

fast-forward or rewind the tape

pause playback

eject the cassette

turn on/off the player

Notes on cassettes

· Break off the cassette tab from side A or B to prevent accidental

recording. If you want to reuse the tape for recording, cover the broken

tab with adhesive tape.

· The use of a cassette with more than 90 minutes of play time is not

recommended except for long, continuous recording or playback.

Tab for side B

Tab for side A

Side A

Recording

Playing a tape

Press

VOLUME +, (VOL +, on the

remote, CFD-S36 only)

or m

Press the button again to resume play

after pause.

POWER

Press

Press the button again to resume recording.

or write to: Sony Direct Response

Center 12451 Gateway Blvd. Fort

Myers, FL 33913

For CFD-S36 USA model only

Declaration of Conformity

Trade Name:

SONY

Model:

CFD-S36

Responsible Party:

Sony

Electronics Inc.

Address:

1 Sony Drive,

Park Ridge, NJ

07656 U.S.A.

Telephone Number: 201-930-6972

This device complies with Part 15 of

the FCC Rules. Operation is subject

to the following two conditions: (1)

This device may not cause harmful

interference, and (2) this device

must accept any interference

received, including interference that

may cause undesired operation.

Owner's Record

The model number is located at the

bottom and the serial number is

located in the battery compartment.

Record these numbers in the spaces

provided below. Refer to them

whenever you call upon your Sony

dealer regarding this product.

Model No.

Serial No.

About this manual

The instructions in this manual are for

the CFD-S26 and CFD-S36. Before you

start reading, check your model

number. The CFD-S36 is the model

used for illustration purpose.

Troubleshooting

General

The power does not come on.

· Make sure the batteries are

inserted correctly.

· Replace all the batteries with new

ones if they are weak.

· You cannot turn on the player

with the remote when you operate

the player on batteries (CFD-S36

only).

The power is not on, and

"bAttErY" and "Error" are

displayed alternately.

· Make sure the batteries are

inserted correctly.

· Replace all the batteries with new

ones if they are weak.

There is no audio.

· Unplug the headphones when

listening through speakers.

Noise is heard.

· Someone is using a portable

telephone or other equipment that

emits radio waves near the player.

tMove the portable telephone,

etc., away from the player.

CD Player

The CD does not play or "no dISC"

lights in the display even when a

CD is in place.

· Place the CD with the label

surface up.

· Clean the CD.

· Take out the CD and leave the CD

compartment open for about an

hour to dry moisture

condensation.

· The CD-R/CD-RW was not

finalized. Finalize the CD-R/CD-

RW with the recording device.

· There is a problem with the

quality of the CD-R/CD-RW,

recording device, or application

software.

The sound drops out.

· Reduce the volume.

· Clean the CD, or replace it if the

CD is badly damaged.

· Place the player in a location free

from vibration.

· Clean the lens with a

commercially available blower.

· The sound may drop out or noise

may be heard when using poor

quality CD-Rs/CD-RWs or if

there is a problem with the

recording device or application

software.

Radio

The audio is weak or has poor

quality.

· Replace all the batteries with new

ones if they are weak.

· Move the player away from the

TV.

The picture of your TV becomes

unstable.

· If you are listening to an FM

program near the TV with an

indoor antenna, move the player

away from the TV.

Using the player on batteries

Insert six size D (R20) batteries (not supplied) into the battery

compartment.

Notes

· Replace the batteries when the OPR/BATT indicator dims or when the

player stops operating. Replace all the batteries with new ones. Before

you replace the batteries, be sure to take out the CD from the player.

· To use the player on batteries, disconnect the AC power cord from the

player.

Connecting the AC power cord

Insert one end of the supplied AC power cord to the AC IN socket located

at the rear of the player, and the other end to the wall outlet.

1 to AC IN

2 to a wall outlet

Choosing Power Sources

To cancel the sleep function

Press POWER to turn off the power.

Note

When you are playing a tape using this function:

If the tape length of one side is longer than the set time, the player will

not go off until the tape reaches the end.

Falling asleep to music

2 Press SLEEP to display "SLEEP."

3 Press SLEEP to select the minutes until the player goes

off automatically.

Each time you press the button, the indication changes

as follows: "60"

t "90" t "120" t no indication t

"10"

t "20" t "30."

1 Play the music source you want.

Precautions

On safety

· As the laser beam used in the CD

player section is harmful to the

eyes, do not attempt to

disassemble the casing. Refer

servicing to qualified personnel

only.

· Should any solid object or liquid

fall into the player, unplug the

player, and have it checked by

qualified personnel before

operating it any further.

Cleaning the cabinet

· Clean the cabinet, panel and

controls with a soft cloth slightly

moistened with a mild detergent

solution. Do not use any type of

abrasive pad, scouring powder, or

solvent, such as alcohol or

benzine.

On power sources

· For AC operation, use the

supplied AC power cord; do not

use any other type.

· The player is not disconnected

from the AC power source

(mains) as long as it is connected

to the wall outlet, even if the

player itself has been turned off.

· Unplug the player from the wall

outlet when it is not to be used for

an extended period of time.

· For battery operation, use six size

D (R20) batteries.

· When the batteries are not to be

used, remove them to avoid

damage that can be caused by

battery leakage or corrosion.

· The nameplate indicating

operating voltage, power

consumption, etc. is located at the

bottom.

On placement

· Do not leave the player in a

location near heat sources, or in a

place subject to direct sunlight,

excessive dust or mechanical

shock.

· Do not place the player on an

inclined or unstable place.

· Do not place anything within 10

mm of the side of the cabinet. The

ventilation holes must be

unobstructed for the player to

operate properly and prolong the

life of its components.

· If the player is left in a car parked

in the sun, be sure to choose a

location in the car where the

player will not be subjected to the

direct rays of the sun.

· Since a strong magnet is used for

the speakers, keep personal credit

cards using magnetic coding or

spring-wound watches away from

the player to prevent possible

damage from the magnet.

On operation

· If the player is brought directly

from a cold to a warm location, or

is placed in a very damp room,

moisture may condense on the

lenses inside the CD player

section. Should this occur, the

player will not operate properly.

In this case, remove the CD and

wait about an hour for the

moisture to evaporate.

· If the player has not been used for

a long time, set it in the playback

mode to warm it up for a few

minutes before inserting a

cassette.

If you have any questions or problems

concerning your player, please consult

your nearest Sony dealer.

Inserting batteries into the remote

(CFD-S36 only)

Insert two size AA (R6) batteries (not supplied)

Replacing batteries

With normal use, the batteries should last for about six months. When the

remote no longer operates the player, replace all the batteries with new

ones.

Note

When you operate the player on batteries, you cannot turn on the player

using the remote.

Display

English

Display

TAPE

STOP/EJECT

PLAY

STOP/EJECT

RADIO

BAND

AUTO PRESET

REC

SLEEP

Erase head

Pinch roller

Record/playback head

Capstan

Lens

Use TYPE I (normal) tape only.

Supplied accessory

AC power cord (1)

Remote control (1) (CFD-S36 only)

Design and specifications are subject to change

without notice.

Optional accessories

Sony MDR headphone series

Use TYPE I (normal) tape only.

1 Press CD (direct power-on).

3 Close the CD compartment.

4 Press u (N on the remote, CFD-S36 only).

The player plays all the tracks once.

Track number

Playing time

adjust the volume

stop playback

pause playback

go to the next track

go back to the previous track

remove the CD

turn on/off the player

Using the display

Checking the total track number and playing time

Press DISPLAY ENT·MEMORY in stop mode.

Checking the remaining time

Press DISPLAY ENT·MEMORY while playing a CD.

To display

the current track number and

the remaining time on the current track*

the number of tracks left

and remaining time on the CD

the current track number

and playing time

* For a track whose number is more than 20, the remaining time appears as

"- -:- -" in the display.

Locating a specific track

To locate

a specific track directly

a point while listening

to the sound

a point while observing

the display

Tip

When you locate a track numbered over 10, press >10 first, then the

corresponding number buttons.

Example:To play track number 23, press >10 first, then 2 and 3.

Note

You cannot locate a specific track if "SHUF" or "PGM" is lit in the display.

Turn off the indication by pressing x.

Repeat Play

1 Press CD.

2 Proceed as follows:

To repeat

a single track

all the tracks

tracks in random order

programmed tracks

To cancel Repeat Play

Press MODE until "REP" disappears from the display.

Total track number

Total playing time

Shuffle Play

1 Press CD.

2 Press MODE until "SHUF" appears in the display.

3 Press u to start shuffle play.

To cancel Shuffle Play

Press MODE until "SHUF" disappears from the display.

Program Play

1 Press CD.

2 Press MODE until "PGM" appears in the display.

3 Press the number buttons for the tracks you want to program

in the order you want. You can arrange the playing order of

up to 20 tracks on a CD.

4 Press u to start program play.

To cancel Program Play

Press MODE until "PGM" disappears from the display.

To check the order of tracks before play

Press DISPLAY ENT·MEMORY.

Every time you press the button, the track number appears in the

programed order.

To change the current program

Press x once if the CD is stopped and twice if the CD is playing. The

current program will be erased. Then create a new program following the

programming procedure.

Tip

You can record your own program. After you've created the program,

insert a blank tape and press z to start recording.

Programmed track

Playing order

Playing a CD

Press

VOLUME +, (VOL +, on the remote,

CFD-S36 only)

(X on the remote, CFD-S36 only)

Press the button again to resume play after

pause.

PUSH OPEN/CLOSE

POWER

Press DISPLAY ENT·MEMORY

once

twice

three times

Do this

1 Press MODE until "REP 1" appears.

2 Press the number button for the track

you want to repeat.

1 Press MODE until "REP ALL" appears.

2 Press u.

1 Press MODE until "SHUF REP" appears.

2 Press u.

1 Press MODE until "PGM REP" appears.

2 Press the number buttons for the tracks

you want to program in the order you

want up to 20 tracks.

3 Press u.

Reinforcing the bass sound

Press MEGA BASS.

"MEGA BASS" appears in the display.

To return to normal sound, press the button again.

Getting the MEGA Xpand effect (CFD-S36 only)

Press MEGA Xpand.

"MEGA Xpand" appears in the display.

You can get the effect of expansion of the sound field.

Location of controls

Adjusting the sound emphasis (MEGA BASS/MEGA Xpand)

1 Press RADIO BAND·AUTO PRESET until the band you

want appears in the display (direct power-on).

Each time you press the button, the indication changes as

follows:

CFD-S36 USA model: "FM"

t "AM" t "TV".

Other models: "FM"

t "AM".

2 Hold down TUNE + or until the frequency digits begin

to change in the display.

The player automatically scans the radio frequencies and

stops when it finds a clear station.

If you can't tune in a station, press the button repeatedly

to change the frequency step by step.

adjust the volume

turn on/off the radio

To improve broadcast reception

Reorient the antenna for FM/TV/WEATHER. Reorient the player itself

for AM.

FM/TV/WEATHER

Tip

If the FM broadcast is noisy, press MODE until "Mono" appears in the

display and the radio will play in monaural.

Listening to the radio

Press

VOLUME +, (VOL +, on the remote,

CFD-S36 only)

POWER

Press

a number button of the track.

(forward) or . (backward)

while playing until you find the

point.

(forward) or . (backward)

in pause until you find the point.

Display

Presetting radio stations

You can store radio stations into the player's memory. You can preset up

to 40 radio stations (CFD-S36 USA model), 20 for FM and 10 for AM and

TV in any order, or 30 radio stations (other models), 20 for FM and 10 for

AM in any order.

1 Press RADIO BAND·AUTO PRESET to select the band.

2 Hold down RADIO BAND·AUTO PRESET for 2 seconds until

"AUTO" flashes in the display.

3 Press DISPLAY ENT·MEMORY.

The stations are stored in memory from the lower frequencies

to the higher ones.

Display

POWER

VOL +,

MEGA

BASS

Remote Control (CFD-S36 only)

Display

About CD-Rs/CD-RWs

This player is compatible with CD-Rs/CD-RWs but playback capability

may vary depending on the quality of the disc, the recording device and

application software.

Notes on CDs

· Before playing, clean the CD with a cleaning cloth. Wipe the CD from the

center out.

· Do not use solvents such as benzine, thinner, commercially available

cleaners or anti-static spray intended for vinyl LPs.

· Do not expose the CD to direct sunlight or heat sources such as hot air

ducts, nor leave it in a car parked in direct sunlight as there can be a

considerable rise in temperature inside the car.

· Do not stick paper or sticker on the CD, nor scratch the surface of the CD.

· After playing, store the CD in its case.

If there is a scratch, dirt or fingerprints on the CD, it may cause tracking error.

2 Press Z PUSH OPEN/CLOSE down to open the CD

compartment and place a CD in the CD compartment.

With the labeled side up

Display

If a station cannot be preset automatically

You need to preset a station with a weak signal manually.

1 Press RADIO BAND·AUTO PRESET to select the band.

2 Tune in a station you want.

3 Hold down the number buttons that you want to preset the new station

on for about 2 seconds.

To select the preset number over 10, press >10 first, then the

corresponding number buttons. You need to hold down the last number

button to enter for about 2 seconds.

(Example: To select 12, press >10 and 1 first, then hold down 2 for about

2 seconds.)

The new station replaces the old one.

Playing preset radio stations

1 Press RADIO BAND·AUTO PRESET to select the band.

2 Press the number buttons to tune in the stored station.

To tune in a preset station over 10, press >10 first, then

corresponding number buttons.

(Example: To tune in a preset station 12, press >10 and 1 first,

and then press 2.)

Checking the weather forecast

(CFD-S36 USA model only)

1 Press WEATHER.

The power turns on automatically.

2 Hold down TUNE + or - until the channel indication begins to

change in the display.

The player automatically scans the weather forecast stations

and stops when it finds a clear station.

If you can't tune in a station, press the button repeatedly to

change the frequency step by step.

Tip

Weather band provides continuous broadcast of the latest weather

information (directly from National Weather Service offices).

REC

PLAY

REW

FF STOP/EJECT PAUSE

Tape

compartment

MEGA BASS

PUSH

OPEN/CLOSE

compartment

VOLUME +,

TUNE ,+

DISPLAY ENT

MEMORY

MODE

(headphones) jack

Number buttons for

CD/RADIO DIRECT OPERATION

POWER

SLEEP

TAPE

RADIO BAND

AUTO PRESET

Tip

To listen through headphones, connect the headphones to the

(headphones) jack.

SLEEP

FUNCTION

Number buttons

MODE

BAND

TUNE +,

MEGA Xpand

(CFD-S36 only)

OPR/BATT

indicator

WEATHER

(CFD-S36 USA

model only)

Remote sensor

(CFD-S36 only)

Display

FUNCTION SLEEP

BAND

TUNE

WEATHER

TUNE

MEGA Xpand

MEGA BASS

CD/RADIO (AC ONLY)

POWER

VOL

MODE

0/10

>10

WEATHER (USA

model only)

PUSH OPEN/CLOSE

RADIO

BAND

AUTO PRESET

TUNE

RADIO

BAND

AUTO PRESET

CD/RADIO DIRECT OPERATION

0/10

>10

CD/RADIO DIRECT OPERATION

0/10

>10

WEATHER

Display