SONY CDP-X5000 - Service Manual Immediate Download

-- 1 --

Model Name Using Similar Mechanism

NEW

Base Unit Type

BU-12A

Optical Pick-up Type

KSS-274A/J-N

SPECIFICATIONS

MICROFILM

COMPACT DISC PLAYER

CDP-X5000

AEP Model

UK Model

E Model

Chinese Model

SERVICE MANUAL

General

-- 2 --

SAFETY-RELATED COMPONENT WARNING !!

COMPONENTS IDENTIFIED BY MARK

! OR

DOTTED LINE WITH MARK ! ON THE SCHEMATIC

DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL

TO SAFE OPERATION. REPLACE THESE COMPO-

NENTS WITH SONY PARTS WHOSE PART NUM-

BERS APPEAR AS SHOWN IN THIS MANUAL OR IN

SUPPLEMENTS PUBLISHED BY SONY.

This appliance is classified as

a CLASS 1 LASER product.

The CLASS 1 LASER

PRODUCT MARKING is

located on the rear exterior.

CAUTION

Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous ra-

diation exposure.

This caution

label is located

inside the unit.

TABLE OF CONTENTS

1. SERVICING NOTE ........................................................... 3

2. GENERAL ........................................................................... 4

3. DISASSEMBLY

3-1.

Top Plate Assembly ............................................................. 8

3-2.

Front Panel Assembly .......................................................... 8

3-3.

Base Unit ............................................................................. 9

3-4.

Back Panel ........................................................................... 9

4. ELECTRICAL BLOCK ADJUSTMENTS ............... 10

5. DIAGRAMS

5-1.

Circuit Boards Location .................................................... 12

5-2.

IC Pin Function

· IC101 Focus/Tracking/Sled/EFM Comparator

(CXD2515AQ )............................................................... 13

· IC201 System Control (CXP84124-043Q) ..................... 16

5-3.

Printed Wiring Board -- Servo, Panel Section -- ............. 20

5-4.

Schematic Diagram -- Servo, Panel Section -- ............... 23

5-5.

Schematic Diagram -- Audio, Power Section -- ............. 28

5-6.

Printed Wiring Board -- Audio, Power Section -- ........... 31

6. EXPLODED VIEWS

6-1.

Top Plate Assembly Seciton .............................................. 37

6-2.

Front Panel Section ........................................................... 38

6-3.

Back Panel Section ............................................................ 39

6-4.

Base Unit Section (BU-12A) ............................................. 40

7. ELECTRICAL PARTS LIST ..................................... 41

The laser component in this product

is capable of emitting radiation

exceeding the limit for Class 1.

Notes on chip component replacement

· Never reuse a disconnected chip component.

· Notice that the minus side of a tantalum capacitor may be

damaged by heat.

Flexible Circuit Board Repairing

· Keep the temperature of soldering iron around 270°C

during repairing.

· Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

· Be careful not to apply force on the conductor when soldering

or unsoldering.

ADVARSEL : USYNLIG LASERSTRÅLING VED ÅBNING NÅR

SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSAETTELSE

FOR STRÅLING.

CAUTION : INVISIBLE LASER RADIATION WHEN OPEN AND

INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.

VARO! : AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALT-

TIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING : OSYNLIG LASERSTRÅLING NÄR DENNA DEL ÄR ÖPP-

NAD OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN.

VORSICHT : UNSICHTBARE LASERSTRAHLUNG, WENN

ABDECKUNG GEÖFFNET UND SICHEREITSVERRIEGELUNG

ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN.

ADVARSEL : USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG

SIKKERHEDSLÅS BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN.

-- 3 --

SECTION 1

SERVICING NOTE

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK

OR BASE UNIT

The laser diode in the optical pick-up block may suffer electrostatic

break-down because of the potential difference generated by the

charged electrostatic load, etc. on clothing and the human body.

During repair, pay attention to electrostatic break-down and also use

the procedure in the printed matter which is included in the repair

parts.

The flexible board is easily damaged and should be handled with

care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on

the disc reflective surface by the objective lens in the optical pick-up

block. Therefore, when checking the laser diode emission, observe

from more than 30 cm away from the objective lens.

LASER DIODE AND FOCUS SEARCH OPERATION CHECK

Carry out the "S curve check" in "CD section adjustment" and check

that the S curve waveform is output three times.

WRITING OF FOCUS/TRACKING AUTO GAIN DATA

General CD palyers using digital servo ICs automatically adjust the

focus/tracking gain each time the disc is changed.

In this unit, the gain of the standard disc (YEDS-18) is written in the

non-volatile memory (IC203:X24C01S) of the servo board so that

the gain need not be re-adjusted when changing discs.

Therefore, if the servo board, IC203 of the servo board, or optical

pick-up has been replaced, be sure to write the auto gain data.

1. Connect TP (ADJ: Pin 3 of CN515) to GND (Ground), and turn

ON the POWER switch.

2. Insert the test disc (YEDS-18). (The TOC data of the disc will be

read.)

This memorizes the auto gain data of the test disc.

Note:

· If the disc is replaced without turning OFF the power, the auto gain

data of the last disc inserted will be memorized.

· If the POWER switch is turned ON without connecting TP (ADJ)

to GND, the auto gain data will not be memorized when the disc is

inserted, and the data memorized the last time will be taken as the

focus/tracking data.

FLUORESCENT INDICATOR TUBE FULL LIGHTING MODE

1. Connect TP (AFJ:Pin 2 of CN515) to GND (Ground), and turn

ON the POWER switch.

2. The bridge check (check for short-circut between pins of the S

RAM (IC202 of the servo board)) is performed, and all the FL

tubes light up if there is no bridge.

3. When a key other than the

p(stop) key is pressed, the correspond-

ing FL tubes lights up.

Each time the

p(stop) key is pressed, all the FL tubes light up.

[SERVO BOARD] -- Conductor Side --

CN514 CN513

CN515

IC104

IC105

IC102

IC202

ADJ

321

AFJ

-- 4 --

SECTION 2

GENERAL

LOCATION OF PARTS AND CONTROLS

UNIT OPERATION BLOCK

4 56 7 8

123

REMOTE COMMANDER (RM-DX5000)

REAR PANEL

1 LINE OUT

2 DIGITAL OUT OPTICAL switch

3 DIGITAL OUT COAXIAL switch

4 DIGITAL OUT BALANCED switch

5 AC IN (230V)

6 DIGITAL OUT BALANCED

7 DIGITAL OUT COAXIAL

8 DIGITAL OUT OPTICAL

!º

!¡

!TM

!£

!¢

!§

!¶

!·

!ª

@º

@¡

@TM

1 DISPLAY MODE button

2 PLAY MODE buttons

CONTINUE button

SHUFFLE button

PROGRAM button

C.INDEX button

3 Number buttons (1-20)

4 CLEAR button

5 >20 button

6 CHECK button

7 REPEAT button

8 A~B button

9 ·(play) button

!º =/+ (*AMS) buttons

!¡ C/c(index search) buttons

!TM TIME button

!£ MUSIC SCAN button

!¢ SPACE button

! FADER button

!§ PEAK SEARCH button

!¶ ERASE button

!· FILE button

!ª p (stop) button

@º P (pause) button

@¡ 0/) (fast forward/

fast rewind) buttons

@TM 0/) SLOW buttons

1 POWER switch

2 Disc lid

3 0/) (fast forward/

fast rewind) buttons

4 =/+ buttons (*AMS)

This section is extracted from

instruction manual.

5 · (play) button/lamp

6 P (pause)button/lamp

7 p (stop)button

8 Display window

*AMS is the abbreviation of Automatic Music Sensor.

-- 5 --