CCD-TRV66E/TRV77E
RMT-708/717
SERVICE MANUAL
VIDEO CAMERA RECORDER
MICROFILM
B501 MECHANISM
Photo: CCD-TRV77E
RMT-717
SPECIFICATIONS
For MECHANISM ADJUSTMENT, refer to
the "8mm Video MECHANICAL
ADJUSTMENT MANUAL
" (9-973-801-11).
AEP Model
CCD-TRV66E/TRV77E
UK Model
E Model
Hong Kong Model
Australian Model
Chinese Model
East European Model
North European Model
Russian Model
CCD-TRV66E
Note : Specifications of CCD-TRV66E are described.
Ver 1.0 1999.01
-- 2 --
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
! OR DOTTED LINE WITH
MARK
! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
· Keep the temperature of the soldering iron around 270°C
during repairing.
· Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
· Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
Model
Destination
Remote Commander
Lens
Optical
Digital
VTR REC
Video Light
Intelligent Accessory Shoe
Time Code
AEP1, AEP2, UK,
EE, NE, RU
RMT-708
20
×
360
× (Note)
!
®
!
!
E, HK, AUS, CN
RMT-708
20
×
360
×
®
®
!
!
CCD-TRV77E
AEP
RMT-717
20
×
80
×
!
!
®
®
Remark
® : With FK-8500 block S005, S007
® : With VL-23 board
® : With VC-214 board (4/10) IC701
Table for difference of function
Note : AEP2, UK model is 80
×.
·
Abbreviation
HK
: Hong Kong Model
AUS
: Australian Model
CN
: Chinese Model
EE
: East European Model
NE
: North European Model
RU
: Russian Model
Supplied accessories
1 Wireless Remote Commander (1)
RMT-708 : CCD-TRV66E
RMT-717 : CCD-TRV77E
2 AC-L10A/L10B/L10C AC power adaptor (1),
Mains lead (1)
3 NP-F330 battery pack (1)
4 CR2025 lithium battery (1)
The lithium battery is already installed in your
camcorder.
5 R6 (size AA) battery for Remote
Commander (2)
6 A/V connecting cable (1)
7 Shoulder strap (1)
8 2-pin conversion adaptor (1)
CCD-TRV66E : E, HK
9 21-pin conversion connector (1)
CCD-TRV66E : AEP, EE, NE, RU, UK/CCD-TRV77E
CCD-TRV66E
-- 3 --
TABLE OF CONTENTS
SERVICE NOTE
1.
POWER SUPPLY DURING REPAIRS ····························· 6
2.
TO TAKE OUT A CASSETTE WHEN NOT EJECT
(FORCE EJECT) ································································ 6
SELF-DIAGNOSIS FUNCTION
1.
Self-diagnosis Function ······················································ 7
2.
Self-diagnosis Display ························································ 7
3.
Service Mode Display ························································ 7
3-1.
Display Method ·································································· 7
3-2.
Switching of Backup No. ··················································· 7
3-3.
End of Display ···································································· 7
4.
Self-diagnosis Code Table ·················································· 8
1.
GENERAL
Checking supplied accessories ·················································· 1-1
Quick Start Guide ······································································ 1-1
1. Connecting the mains lead ················································· 1-1
2. Inserting a cassette ····························································· 1-1
3. Recording a picture ···························································· 1-1
4. Monitoring the playback picture on the LCD screen ········· 1-1
Getting Started ··········································································· 1-1
Using this manual ·································································· 1-1
Step 1 Preparing the power supply ········································ 1-2
Step 2 Inserting a cassette ······················································ 1-3
Recording Basics ···································································· 1-4
Recording a picture ································································ 1-4
Checking the recording
END SEARCH/EDITSEARCH/Rec Review ····················· 1-6
Playback Basics ······································································ 1-8
Playing back a tape ································································ 1-7
Viewing the recording on TV ················································ 1-7
Advanced Recording Operations ··············································· 1-8
Photo recording ······································································ 1-8
Using the wide mode ····························································· 1-9
Using the fader function ························································ 1-9
Using special effects Picture effect ··································· 1-10
Using special effects Digital effect ··································· 1-10
Using the PROGRAM AE function ····································· 1-11
Adjusting the exposure manually ········································ 1-12
Focusing manually ······························································· 1-12
Superimposing a title ··························································· 1-13
Making your own titles ························································ 1-13
Using the built-in light ························································· 1-14
Advanced Playback Operations ··············································· 1-15
Playing back a tape with digital effects ······························· 1-15
Editing on Other Equipment ···················································· 1-15
Dubbing a tape ····································································· 1-15
Recording video or TV programmes ··································· 1-16
Customizing Your Camcorder ················································· 1-16
Changing the MENU settings ·············································· 1-16
Resetting the date and time ·················································· 1-18
Additional Information ···························································· 1-18
Usable cassettes and playback modes ·································· 1-18
Changing the lithium battery in your camcorder ················· 1-19
Troubleshooting ··································································· 1-19
Self-diagnosis display ·························································· 1-20
Warning indicators and messages ········································ 1-20
Using your camcorder abroad ·············································· 1-21
Maintenance information and precautions ··························· 1-21
Quick Reference ······································································ 1-22
Identifying the parts and controls ········································ 1-22
Quick function guide ··························································· 1-24
2.
DISASSEMBLY
2-1.
LCD Unit, PD-105 Board ················································ 2-2
2-2.
Cabinet (R) Assembly (TRV66E), (TRV77E) ················· 2-3
2-3.
Mechanism Deck ····························································· 2-4
2-4.
EVF Block, VF-129 Board ·············································· 2-5
2-5.
Lens Block (TRV66E), (TRV77E) ·································· 2-6
2-6.
Mechanism Deck, VC-214, DD-117 Boards ··················· 2-8
2-7.
Video Light (TRV66E) ·················································· 2-10
2-8.
CF-56 Board ·································································· 2-10
2-9.
How to Identify Drum and Note ···································· 2-10
2-10. Circuit Boards Location ················································ 2-11
2-11. Flexible Boards Location ·············································· 2-12
3.
BLOCK DIAGRAMS
3-1.
Overall Block Diagram ··················································· 3-1
3-2.
Camera/Video Block Diagram ········································ 3-5
3-3.
VTR/Camera Control Block Diagram ····························· 3-9
3-4.
Servo Block Diagram ···················································· 3-12
3-5.
Mode Control Block Diagram ······································· 3-15
3-6.
Audio Block Diagram ··················································· 3-19
3-7.
LCD Block Diagram ····················································· 3-23
3-8.
EVF Block Diagram ······················································ 3-27
3-9.
Power Block Diagram ··················································· 3-29
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1.
Frame Schematic Diagram-1 ··········································· 4-1
Frame Schematic Diagram-2 ··········································· 4-4
4-2.
Printed Wiring Boards and Schematic Diagrams ············ 4-7
· CD-209 (CCD Imager)
Printed Wiring Board and
Schematic Diagram ········································· 4-8
· VC-214 (Camera Processor, Y/C Processor, Focus/Zoom
Motor Drive, REC/PB Head AMP, Video/Interface,
IR Transmitter, Mode Control, System Control, Servo,
HI Control, Audio Processor)
Printed Wiring Board ···································· 4-11
· VC-214 (Camera Processor)(1/10)
Schematic Diagram ....................................... 4-17
· VC-214 (Y/C Processor)(2/10)
Schematic Diagram ······································· 4-19
· VC-214 (Focus/Zoom Motor Drive)(3/10)
Schematic Diagram ······································· 4-25
· VC-214 (REC/PB Head AMP)(4/10)
Schematic Diagram ······································· 4-27
· VC-214 (Video/Interface)(5/10)
Schematic Diagram ······································· 4-31
· VC-214 (IR Transmitter)(6/10)
Schematic Diagram ······································· 4-33
· VC-214 (Mode Control)(7/10)
Schematic Diagram ······································· 4-36
· VC-214 (Servo)(8/10)
Schematic Diagram ······································· 4-39
· FP-249 (S/T Reel Sensor), FP-356 (Top Sensor),
FP-355 (Tape LED) Flexible Board
Printed Wiring Boards ··································· 4-42
· VL-23 (Video Light) (TRV66E only)
Printed Wiring Board ···································· 4-43
· VC-214 (HI Control)(9/10)
Schematic Diagram ······································· 4-44
· VC-214 (Audio)(10/10)
Schematic Diagram ······································· 4-47
· SE-83 (Steady Shot), PJ-92 (AV IN/OUT)
Printed Wiring Boards ··································· 4-50
· SE-83 (Steady Shot), PJ-92 (AV IN/OUT)
Schematic Diagrams ····································· 4-53
· MA-351 (Stereo MIC AMP, Laser Link)
Printed Wiring Board ···································· 4-55
· MA-351 (Stereo MIC AMP, Laser Link)
Schematic Diagram ······································· 4-57
-- 4 --
· PD-105 (RGB Decoder, LCD, Timing Generator,
Back Light Drive)
Printed Wiring Board ···································· 4-60
· PD-105 (RGB Decoder, LCD)(1/2)
Schematic Diagram ······································· 4-63
· PD-105 (Timing Generator, Back Light Drive)(2/2)
Schematic Diagram ······································· 4-67
· VF-129 (B/W EVF)
Printed Wiring Board and
Schematic Diagram ....................................... 4-69
· CF-56 (User Control)
Printed Wiring Board .................................... 4-72
· CF-56 (User Control)
Schematic Diagram ······································· 4-75
· DD-117 (DC/DC Converter)
Printed Wiring Board ···································· 4-79
· DD-117 (DC/DC Converter)
Schematic Diagram ······································· 4-81
· FK-8500, SS-8500 (Control Switch Block)
Schematic Diagram ······································· 4-88
5.
ADJUSTMENTS
5-1.
CAMERA SECTION ADJUSTMENT ··························· 5-1
1-1.
Preparations before Adjustment (Camera Section) ········· 5-1
1-1-1. List of Service Tools ························································ 5-1
1-1-2. Adjusting Items When Replacing Main Parts ················· 5-2
1-1-3. Preparations ····································································· 5-3
1-1-4. Precaution ········································································ 5-5
1.
Setting the Switch ···························································· 5-5
2.
Order of Adjustments ······················································ 5-5
3.
Subjects ··········································································· 5-5
1-2.
Initialization of D, E, F Page Data ·································· 5-6
1.
Initializing the D, E, F Page Data ···································· 5-6
2.
Modification of D, E, F Page Data ·································· 5-6
3.
D Page Table ···································································· 5-6
4.
F Page Table ···································································· 5-7
5.
E Page Table ·································································· 5-10
1-3.
Camera System Adjustments ········································· 5-13
1.
HALL Adjustment ························································· 5-13
2.
Flange Back Adjustment ··············································· 5-13
2-1.
Flange Back Adjustment (1) ·········································· 5-13
2-2.
Flange Back Adjustment (2) ·········································· 5-14
3.
Flange Back Check ························································ 5-14
4.
Picture Frame Setting ···················································· 5-15
5.
AGC Gain Calibration Adjustment ······························· 5-15
6.
Color Reproduction Adjustment ···································· 5-16
7.
IRIS IN/OUT Adjustment ············································· 5-16
8.
MAX GAIN Adjustment ··············································· 5-17
9.
Auto White Balance Standard Data Input ····················· 5-17
10.
Auto White Balance Adjustment ··································· 5-18
11.
White Balance Check ···················································· 5-19
12.
Angular Velocity Sensor Sensitivity Preset and
Steady Shot Check ························································· 5-20
1-4.
Monochrome Electronic Viewfinder System
Adjustment ···································································· 5-21
1-4-1. Horizontal Slant Check ················································· 5-21
1-4-2. Centering Adjustment ···················································· 5-21
1-4-3. Focus Adjustment ·························································· 5-21
1-4-4. Aberration Adjustment ·················································· 5-22
1-4-5. Horizontal Amplitude Adjustment (VF-129 board) ······ 5-22
1-4-6. Vertical Amplitude Adjustment (VF-129 board) ··········· 5-23
1-4-7.Brightness Adjustment (VF-129 Board) ························ 5-23
1-4-8. Horizontal Amplitude, Vertical Amplitude,
Focus Check ·································································· 5-23
1-5.
LCD System Adjustment ··············································· 5-24
1.
LCD Initial Data Input ·················································· 5-24
2.
VCO Adjustment (PD-105 board) ································· 5-25
3.
D range Adjustment (PD-105 board) ····························· 5-25
4.
Bright Adjustment (PD-105 board) ······························· 5-26
5.
Contrast Adjustment (PD-105 board) ···························· 5-26
6.
V-COM Level Adjustment (PD-105 board) ·················· 5-27
7.
Color Adjustment (PD-105 board) ································ 5-27
8.
V-COM Adjustment (PD-105 board) ···························· 5-28
9.
White Balance Adjustment (PD-105 board) ·················· 5-28
5-2.
MECHANISM SECTION ADJUSTMENT ·················· 5-29
2-1.
Operating Without Cassette ··········································· 5-29
2-2.
Tape Path Adjustment ···················································· 5-29
5-3.
VIDEO SECTION ADJUSTMENT ······························ 5-30
3-1.
Preparations Before Adjustments ·································· 5-30
3-1-1. Equipment to Required ·················································· 5-30
3-1-2. Precautions on Adjusting ··············································· 5-31
3-1-3. Adjusting Connectors ···················································· 5-31
3-1-4. Connecting the Equipments ··········································· 5-32
3-1-5. Alignment Tape ····························································· 5-33
3-1-6. Input/Output Level and Impedance ······························· 5-33
3-1-7. Recording Mode (Standard 8/Hi8) Switching ··············· 5-33
3-2.
System Control System Adjustment ······························ 5-34
1.
Initialization of D, E, F Page Data ································ 5-34
2.
Battery End Adjustment (VC-214 board) ······················ 5-34
3-3.
Servo System Adjustments ············································ 5-35
1.
CAP FG Offset Adjustment (VC-214 board) ················ 5-35
2.
Switching Position Adjustment (VC-214 board) ··········· 5-35
3-4.
Video System Adjustments ············································ 5-36
1.
28 MHz Origin Oscillation Adjustment
(VC-214 board) ····························································· 5-36
2.
AFC f0 Adjustment (VC-214 board) ······························ 5-36
3.
Filter f0 Adjustment (VC-214 board) ····························· 5-37
4.
Y OUT Level Adjustment (VC-214 board) ··················· 5-37
5.
C OUT Level Adjustment (VC-214 board) ··················· 5-38
6.
RP Filter f0 Adjustment (VC-214 board) ······················· 5-38
7.
REC Y Current Adjustment (VC-214 board) ················ 5-39
8.
REC L Level Adjustment (VC-214 board) ···················· 5-40
9.
REC C Current Adjustment (VC-214 board) ················ 5-41
3-5.
IR Transmitter Adjustments ··········································· 5-42
1.
IR Video Carrier Frequency Adjustment
(VC-214 board) ····························································· 5-42
2.
IR Video Deviation Adjustment (VC-214 board) ·········· 5-42
3.
IR Audio Deviation Adjustment (VC-214 board) ········· 5-43
3-6.
Audio System Adjustment ············································· 5-44
1.
1.5 MHz Deviation Adjustment (VC-214 board) ·········· 5-45
2.
1.7 MHz Deviation Adjustment (VC-214 board) ·········· 5-45
3.
BPF f0 Adjustment (VC-214 board) ····························· 5-46
5-4.
SERVICE MODE ·························································· 5-47
4-1.
Adjustment Remote Commander ·································· 5-47
1.
Using the Adjustment Remote Commander ·················· 5-47
2.
Precautions Upon Using the Adjustment Remote
Commander ··································································· 5-47
4-2.
Data Process ·································································· 5-48
4-3.
Service Mode ································································· 5-49
1.
Test Mode Setting ·························································· 5-49
2.
Emergency Memory Address ········································ 5-50
2-1.
EMG Code (Emergency Code) ····································· 5-50
2-2.
MSW Codes ·································································· 5-51
3.
Bit Value Discrimination ··············································· 5-52
4.
Input/Output Selection Check ······································· 5-52
5.
LED, LCD (Display Window) Check ··························· 5-52
6.
Record of Use Check ····················································· 5-53
7.
Switch Check (1) ··························································· 5-53
8.
Switch Check (2) ··························································· 5-54
9.
Headphone Jack Check ················································· 5-54
6.
REPAIR PARTS LIST
6-1.
Exploded Views ······························································· 6-1
6-1-1. Front Panel (D) Block and Battery Panel (P) Block
Assembly ········································································· 6-1
-- 5 --
* The color reproduction frame is shown on page 253.
6-1-2. Cabinet (R) Block Assembly ··········································· 6-2
6-1-3. LCD Block Assembly ······················································ 6-3
6-1-4. Cabinet (L) Block and Main Boards Assembly ··············· 6-4
6-1-5. EVF Block Assembly ······················································ 6-5
6-1-6. Cassette Compartment Assembly ···································· 6-6
6-1-7. LS Chassis Assembly ······················································ 6-7
6-1-8. Mechanism Chassis Assembly ········································ 6-8
6-2.
Electrical Parts List ························································· 6-9