PIONEER XV-DV424/NVXJ - Service Manual Immediate Download

ORDER NO.

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.

PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium

PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936

PIONEER CORPORATION 2004

PHONES

6 DVD/CD

0 OPEN/CLOSE

FM/AM

VOL.

ñ DOWN

UP +

STANDBY/ON

XV-DV525

RRV2906

DVD/CD RECEIVER

XV-DV525

XV-DV424

XV-DV323 (DCS-323)

THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).

XV-DV323 is a system(s) component.

Model

Type

Power Requirement

Regional restriction

codes (Region No.)

Remarks

XV-DV525

MYXJ

AC220-230V

XV-DV525

NVXJ

AC230V

XV-DV424

MYXJ

AC220-230V

XV-DV424

NVXJ

AC230V

XV-DV323

MYXJ

AC220-230V

XV-DV323

NVXJ

AC230V

Component

System

Service Manual

Remarks

5.1CH SURROUND SYSTEM

DCS-323

RRV2927

DVD/CD RECEIVER

XV-DV323

RRV2906

This manual.

SPEAKER SYSTEM

S-DV323

RRV2899

For details, refer to "Important symbols for good services".

T-ZZK MAR. 2004 printed in Japan

XV-DV525

1234

123

SAFETY INFORMATION

This service manual is intended for qualified service technicians ; it is not meant for the casual do-

it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been

trained to properly and safely repair complex products such as those covered by this

manual.Improperly performed repairs can adversely affect the safety and reliability of the product

and may void the warranty. If you are not qualified to perform the repair of this product properly and

safely, you should not risk trying to do so and refer the repair to a qualified service technician.

WARNING !

THE AEL (ACCESSIBLE EMISSION LEVEL) OF THE LASER POWER OUTPUT IS LESS THAN CLASS 1

BUT THE LASER COMPONENT IS CAPABLE OF EMITTING RADIATION EXCEEDING THE LIMIT FOR

CLASS 1.

A SPECIALLY INSTRUCTED PERSON SHOULD DO SERVICING OPERATION OF THE APPARATUS.

LASER DIODE CHARACTERISTICS

FOR DVD : MAXIMUM OUTPUT POWER : 5 mW

WAVELENGTH : 650 nm

FOR CD :

MAXIMUM OUTPUT POWER : 7 mW

WAVELENGTH : 780 nm

Additional Laser Caution

1. Laser Interlock Mechanism

· Loading switch (S101 on the LOAB Assy) is used for interlock

mechanism of the laser.

When this switch turned ON in SW2 (CLOSE) side (OPEN signal is

0V and CLOSE signal is 3.5V), a laser becomes the status which can

completely oscillation.

Furthermore, the laser completely oscillates in the disc judgment and

disc playback.

When player is power ON state and laser diode is not completely

oscillating, 780nm laser diode is always oscillating by half power.

· Laser diode is driving with Q201 (650nm LD) and Q211 (780nm LD)

on the DVDM Assy.

Therefore, when short-circuit between the emitter and collector of these

transistors or the base voltage is supplied for transistors turn on, the

laser oscillates. (failure mode)

· In the test mode

, there is the mode that the laser oscillates except

for the disc judgment and playback. LD ON mode in the test mode

oscillates with the laser forcibly.

The interlock mechanism mentioned above becomes invalid in this

mode.

2. When the cover is open, close viewing through the objective lens with

the naked eye will cause exposure to the laser beam.

LABEL CHECK

VRW1872

Name Label

: Refer to page 82.

XV-DV525

678

[ Important symbols for good services ]

In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely.

When you find the procedures bearing any of the symbols, be sure to fulfill them:

2. Adjustments

To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable.

In accordance with the procedures or instructions described in this manual, adjustments should be performed.

3. Cleaning

For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning,

proper cleaning should be performed to restore their performances.

5. Lubricants, glues, and replacement parts

Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying

glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the

prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed

ones should be used.

4. Shipping mode and shipping screws

To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or

the shipping screws should be installed before shipping out in accordance with this manual, if necessary.

1. Product safety

You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and

should keep the safety during servicing by following the safety instructions described in this manual.

Disc / content format playback

compatibility

This player is compatible with a wide range of

disc types (media) and formats. Playable discs

will generally feature one of the following logos

on the disc and/or disc packaging. Note

however that some disc types, such as

recordable CD and DVD, may be in an

unplayable formatósee below for further

compatibility information.

is a trademark of Fuji Photo Film Co. Ltd.

Also compatible with KODAK Picture CD

This player supports the IECís Super VCD stan-

dard for superior picture quality, dual

soundtracks, and widescreen support.

DVD-Video

DVD-R

DVD-RW

Video CD

Fujicolor CD

Audio CD

CD-R

CD-RW

VIDEO

Super Video CD (Super VCD)

XV-DV525

1234

123

CONTENTS

SAFETY INFORMATION ..................................................................................................................................... 2

1. SPECIFICATIONS ............................................................................................................................................ 5

2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 6

2.1 PACKING ................................................................................................................................................... 6

2.2 EXTERIOR SECTION................................................................................................................................ 8

2.3 FRONT PANEL SECTION ....................................................................................................................... 10

2.4 01 LOADER ASSY................................................................................................................................... 12

2.5 TRAVERSE MECHA ASSY-S .................................................................................................................. 14

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ..........................................................................................16

3.1 BLOCK DIAGRAM ................................................................................................................................... 16

3.2 LOAB ASSY and OVERALL WIRING DIAGRAM..................................................................................... 18

3.3 DVDM ASSY(1/3)..................................................................................................................................... 20

3.4 DVDM ASSY(2/3)..................................................................................................................................... 22

3.5 DVDM ASSY(3/3)..................................................................................................................................... 24

3.6 DSP ASSY (1/2)....................................................................................................................................... 26

3.7 DSP ASSY (2/2)....................................................................................................................................... 28

3.8 6CH AMP ASSY ...................................................................................................................................... 30

3.9 CONTROL(1/4), TRADE3 and TRADE2 ASSYS ..................................................................................... 32

3.10 CONTROL ASSY(2/4)............................................................................................................................ 34

3.11 CONTROL ASSY(3/4)............................................................................................................................ 36

3.12 CONTROL ASSY(4/4) and HP ASSYS.................................................................................................. 38

3.13 POWER ASSY(1/2)................................................................................................................................ 40

3.14 POWER ASSY(2/2) and TRADE1 ASSYS............................................................................................. 42

3.15 EURO SCART ASSY ............................................................................................................................. 44

3.16 DISPALY ASSY ...................................................................................................................................... 46

3.17 WAVEFORMS ........................................................................................................................................ 48

4. PCB CONNECTION DIAGRAM ..................................................................................................................... 49

4.1 LOAB ASSY ............................................................................................................................................. 49

4.2 DVDM ASSY ............................................................................................................................................ 50

4.3 DSP ASSY ............................................................................................................................................... 52

4.4 6CH AMP ASSY ...................................................................................................................................... 54

4.5 CONTROL ASSY ..................................................................................................................................... 56

4.6 TRADE2,TRADE3 and HP ASSYS .......................................................................................................... 60

4.7 POWER ASSY ......................................................................................................................................... 62

4.8 TRADE1, EURO SCART and DISPLAY ASSYS...................................................................................... 66

5. PCB PARTS LIST ........................................................................................................................................... 70

6. ADJUSTMENT ............................................................................................................................................... 77

6.1 ADJUSTMENT ITEMS AND LOCATION ................................................................................................. 77

6.2 JIGS AND MEASURING INSTRUMENTS ............................................................................................... 77

6.3 NECESSARY ADJUSTMENT POINTS ................................................................................................... 78

6.4 TEST MODE ............................................................................................................................................ 79

6.5 MECHANISM ADJUSTMENT .................................................................................................................. 80

7. GENERAL INFORMATION ............................................................................................................................. 82

7.1 DIAGNOSIS ............................................................................................................................................. 82

7.1.1 TEST MODE ...................................................................................................................................... 82

7.1.2 DISPLAY SPECIFICATIONS OF THE TEST MODE ......................................................................... 84

7.1.3 FUNCTIONAL SPECIFICATION OF THE SHORTCUT KEY ............................................................ 85

7.1.4 SPECIFICATION OF MODEL INFORMATION DISPLAY .................................................................. 86

7.1.5 FUNCTIONAL SPECIFICATION OF THE SERVICE MODE ............................................................. 87

7.1.6 MECHANICAL ERROR HISTORY..................................................................................................... 88

7.1.7 ID NUMBER AND DATA SETTING.................................................................................................... 93

7.1.8 METHOD FOR DIAGNOSING DEGRADATION OF THE LDS ON THE PICKUP ASSY .................. 96

7.1.9 TROUBLE SHOOTING ...................................................................................................................... 97

7.1.10 DSP TROUBLE SHOOTING ......................................................................................................... 100

7.1.11 DISASSEMBLY.............................................................................................................................. 102

7.2 IC ........................................................................................................................................................... 111

7.3 EXPLANATION ...................................................................................................................................... 114

7.3.1 SEQUENCE AFTER POWER ON ................................................................................................... 114

7.3.2 PROTECTION CIRCUIT.................................................................................................................. 115

7.4 CLEANING............................................................................................................................................. 119

8. PANEL FACILITIES ...................................................................................................................................... 120

XV-DV525

678

1. SPECIFICATIONS

Amplifier section

Continuous Power Output (RMS):

Argentina and Brazil models:

Front, Center, Surround . . . 90 W per channel

(1 kHz, 10 % T.H.D., 6

)

Subwoofer . . .90 W (100 Hz, 10 % T.H.D., 6 )

All other models:

Front, Center, Surround . . 100 W per channel

(1 kHz, 10 % T.H.D., 6

)

Subwoofer . .100 W (100 Hz, 10 % T.H.D., 6 )

Continuous Power Output:

Argentina and Brazil models:

Front, Center, Surround . . . 68 W per channel

(1 kHz, 1 % T.H.D., 6

)

Subwoofer . . . .68 W (100 Hz, 1 % T.H.D., 6 )

All other models:

Front, Center, Surround . . . 75 W per channel

(1 kHz, 1 % T.H.D., 6

)

Subwoofer . . . .75 W (100 Hz, 1 % T.H.D., 6 )

Disc section

Digital audio

characteristics . . . . . . . . . DVD fs: 96 kHz, 24-bit

Type . . . . . . . DVD system, video CD system and

compact disc digital audio system

Total harmonic distortion. . . . . . . . . . . . . 0.004%

Frequency

response . . . .4 Hz to 44 kHz (96kHz sampling) /

4 Hz to 22 kHz (48kHz sampling)

Wow and Flutter . . . . . . . .Limit of measurement

(

±0.001 % W.PEAK) or less (JEITA)

FM tuner section

Frequency range. . . . . . . . . . . . . 87.5 108 MHz

Antenna . . . . . . . . . . . . . . . . . . 75

, unbalanced

AM tuner section

Frequency range

With 9kHz step . . . . . . . .531 kHz to 1,602 kHz

With 10kHz step (

Not applicable to

the European model). . 530 kHz to 1,700 kHz

Antenna . . . . . . . . . . . . . . . . . . . . . Loop antenna

Miscellaneous

Power requirements

European/Singapore/South African

models . . . . . . . . . . . . AC 220-230 V, 50/60 Hz

U.K. model . . . . . . . . . . . . .AC 230 V, 50/60 Hz

Australian/New Zealand/Malaysian

models . . . . . . . . . . . . . . . AC 240 V, 50/60 Hz

Argentina/Brazil models . . AC 220 V, 50/60 Hz

Hong Kong model . . . . . .AC 220-230 V, 50 Hz

Taiwan model. . . . . . . . . .AC 110-120 V, 60 Hz

Mexican model . . . . . . . . AC 127 V, 50/60 Hz

Power consumption . . . . . . . . . . . . . . . . . . 175W

Power consumption in standby . . . . . . . . . 0.5 W

Dimensions . . . . 420 (W) x 70 (H) x 396 (D) mm

Weight

Manufactured under license from Dolby

Laboratories. "Dolby", "Pro Logic" and the double-D

symbol are trademarks of Dolby Laboratories.

"DTS" and "DTS Digital Surround" are registered

trademarks of Digital Theater Systems, Inc.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0 kg

Accessories (DVD/CD receiver)

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . 1

AA/R6 dry cell batteries. . . . . . . . . . . . . . . . . . . .2

Video cable (yellow plugs) . . . . . . . . . . . . . . . . . 1

AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . .1

FM antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Setup Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Operating instructions . . . . . . . . . . . . . . . . . . . . 1

Warranty Card (

European, Australian and New

Zealand models only) . . . . . . . . . . . . . . . . . . . .1

Note

· Specifications and design subject to

possible modification without notice, due

to improvements.

ST+

TUNE+

ENTER

TUNE

MASTER

VOLUME

STANDBY/ON

FM/AM

OPEN CLOSE

DISPLAY

DVD

TUNER

LINE

L1/L2

DVD MENU

RETURN

SOUND

TV CONTROL

VOL

INPUT

OPEN

MUTE

Accessories

· Power cord

(MYXJ : ADG1154)

· FM Antenna

(ADH7030)

· Power cord

(NVXJ : ADG1156)

· AM Loop Antenna

(ATB7013)

· Video Cable

(L = 1.5m)(XDE3046)

· Remote Control

(XXD3077 : XV-DV525)

(XXD3076 : XV-DV424)

(XXD3076 : XV-DV323)

· Dry Cell Batteries

(R6P, AA)

Yellow