PIONEER VSX-D711-K/MYXJIEW - Service Manual Immediate Download

ORDER NO.

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.

PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium

PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936

PIONEER CORPORATION 2002

Model

Type

Power Requirement

Remarks

VSX-D711-K

MVXJI

AC230V

VSX-D711-K

MYXJIEW

AC220-230V

VSX-D711-K

MYXJIGR

AC220-230V

VSX-D711-S

MYXJIEW

AC220-230V

RRV2607

AUDIO/VIDEO MULTI-CHANNEL RECEIVER

VSX-D711-K

T ZZV APR. 2002 Printed in Japan

VSX-D711-S

THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).

For details, refer to "Important symbols for good services" on page 3.

DOWN

ENTER

INPUT

SELECTOR

MASTER VOLUME

MULTI JOG

STANDBY

STANDBY/ON

PHONES

Nm-Û,,

OFF

VSX-D711-K, VSX-D711-S

SAFETY INFORMATION

This service manual is intended for qualified service technicians; it is not meant for the casual

do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been

trained to properly and safely repair complex products such as those covered by this manual.

Improperly performed repairs can adversely affect the safety and reliability of the product and may

void the warranty. If you are not qualified to perform the repair of this product properly and safely, you

should not risk trying to do so and refer the repair to a qualified service technician.

WARNING

This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to

cause cancer, birth defects or other reproductive harm.

Health & Safety Code Section 25249.6 Proposition 65

NOTICE

(FOR CANADIAN MODEL ONLY)

Fuse symbols

(fast operating fuse)

and/or

(slow operating fuse) on PCB indicate that replacement

parts must be of identical designation.

REMARQUE

(POUR MODÈLE CANADIEN SEULEMENT)

Les symboles de fusible

(fusible de type rapide)

et/ou

(fusible de type lent) sur CCI indiquent que

les pièces de remplacement doivent avoir la même désignation.

ANY MEASUREMENTS NOT WITHIN THE

LIMITS OUTLINED ABOVE ARE INDICATIVE

OF A POTENTIAL SHOCK HAZARD AND

MUST BE CORRECTED BEFORE RETURN-

ING THE APPLIANCE TO THE CUSTOMER.

2. PRODUCT SAFETY NOTICE

Many electrical and mechanical parts in the appliance

have special safety related characteristics. These are

often not evident

from visual

inspection nor the

protection afforded by them necessarily can be obtained

by using replacement components rated for voltage,

wattage, etc. Replacement parts which have these

special safety characteristics are identified in this

Service Manual.

Electrical components having such features are

identified by marking with a

on the schematics and

on the parts list in this Service Manual.

The use of a substitute replacement component which

does not have the same safety characteristics as the

PIONEER recommended replacement one, shown in the

parts list in this Service Manual, may create shock, fire,

or other hazards.

Product Safety is continuously under review and new

instructions are issued from time to time. For the latest

information, always consult the current PIONEER

Service Manual. A subscription to, or

additional copies

of, PIONEER Service Manual may be obtained at a

nominal charge from PIONEER.

(FOR USA MODEL ONLY)

1. SAFETY PRECAUTIONS

The following check should be performed for the

continued protection of the customer and service

technician.

LEAKAGE CURRENT CHECK

Measure leakage current to a known earth ground

(water pipe, conduit, etc.) by connecting a leakage

current tester such as Simpson Model 229-2 or

equivalent between the earth ground and all exposed

metal parts of the appliance (input/output terminals,

screwheads, metal overlays, control shaft, etc.). Plug

the AC line cord of the appliance directly into a 120V

AC 60 Hz outlet and turn the AC power switch on. Any

current measured must not exceed 0.5 mA.

Device

under

test

Leakage

current

tester

Earth

ground

Reading should

not be above

0.5 mA

Also test with

plug reversed

(Using AC adapter

plug as required)

Test all

exposed metal

surfaces

AC Leakage Test

VSX-D711-K, VSX-D711-S

[ Important symbols for good services ]

In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely.

When you find the procedures bearing any of the symbols, be sure to fulfill them:

2. Adjustments

To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable.

In accordance with the procedures or instructions described in this manual, adjustments should be performed.

3. Cleaning

For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning,

proper cleaning should be performed to restore their performances.

5. Lubricants, glues, and replacement parts

Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying

glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the

prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed

ones should be used.

4. Shipping mode and shipping screws

To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or

the shipping screws should be installed before shipping out in accordance with this manual, if necessary.

1. Product safety

You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and

should keep the safety during servicing by following the safety instructions described in this manual.

VSX-D711-K, VSX-D711-S

SAFETY INFORMATION ................................................................... 2

1. SPECIFICATIONS ......................................................................... 5

2. EXPLODED VIEWS AND PARTS LIST ......................................... 6

2.1 PACKING ................................................................................ 6

2.2 EXTERIOR ............................................................................. 8

2.3 FRONT PANEL ..................................................................... 10

3. BLOCKDIAGRAM AND SCHEMATIC DIAGRAM .......................... 12

3.1 BLOCK DIAGRAM ................................................................ 12

3.2 OVERALL WIRING CONNECTION DIAGRAM ................... 14

3.3 DD & INPUT ASSY(1/4) ....................................................... 16

3.4 DD & INPUT ASSY(2/4) ....................................................... 18

3.5 DD & INPUT ASSY(3/4) ....................................................... 20

3.6 DD & INPUT ASSY(4/4) ....................................................... 22

3.7 AMP & PRIMARY(1/2), TRANS2 and TRANS3 ASSYS ............. 24

3.8 AMP & PRIMARY(2/2), REGULATOR, HASHIGETA

B TO B , AMP INPUT and TRANS 1 ASSYS ................ 26

3.9 DIGITAL IN ASSY ................................................................. 28

3.10 KAWA ASSY ....................................................................... 29

3.11 VIDEO and 6CH IN ASSYS ................................................ 30

3.12 S. VIDEO ASSY .................................................................. 31

3.13 FRONT, R. ENCODER and POWER SW ASSYS ............. 32

3.14 FRONT VIDEO and H.P. ASSYS ....................................... 34

3.15 TRANS4 and MECHA SW ASSYS ..................................... 35

3.16 FM/AM TUNER MODULE .................................................. 36

4. PCB CONNECTION DIAGRAM ................................................... 38

4.1 TRANS1, TRANS2, TRANS3 and TRANS4 ASSYS ............ 39

4.2 DD & INPUT ASSY ............................................................... 40

4.3 AMP & PRIMARY, AMP INPUT and MECHA SW ASSYS ......... 44

4.4 REGULATOR, HASHIGETA and KAWA ASSYS ................. 46

4.5 B TO B, DIGITAL IN, VIDEO and 6CH IN ASSYS ...................... 48

4.6 S. VIDEO and FRONT VIDEO ASSYS ....................................... 50

4.7 FRONT, POWER SW, H.P. and R. ENCODER ASSYS ............. 52

4.8 FM/AM TUNER MODULE ........................................................... 56

5. PCB PARTS LIST ........................................................................ 57

6. ADJUSTMENT ............................................................................. 63

7. GENERAL INFORMATION ......................................................... 64

7.1 DIAGNOSIS .......................................................................... 64

7.1.1 U-COM BLOCKDIAGRAM .................................................... 64

7.1.2 POWER ON AND OFF SEQUENCE .................................... 65

7.1.3 PROTECTION CIRCUIT ....................................................... 67

7.2.2 PCB LOCATION ................................................................... 68

7.2 PARTS .................................................................................. 69

7.2.1 IC ........................................................................................... 69

7.2.2 DISPLAY ............................................................................... 77

7.3 CLEANING ........................................................................... 78

8. PANEL FACILITIES ..................................................................... 79

CONTENTS

VSX-D711-K, VSX-D711-S

Accessories

Remote control unit

(XXD3042)

AM loop antenna

(ATB7009)

FM wire antenna

(ADH7005)

AA size IEC R6P

Dry cell batteries (x2)

Miscellaneous

Power Requirements

UK model .......................................................... AC 230 V, 50/60 Hz

European model ......................................... AC 220-230 V, 50/60 Hz

Power Consumption

VSX-D711 .......................................................................... 250W

In Standby ............................................................................. 1 W

Dimensions ................................... 420 (W) x 158 (H) x 401 (D) mm

.........................................................10 kg

Furnished Parts

AM loop antenna ............................................................................ 1

FM wire antenna ............................................................................ 1

Dry cell batteries (AA size IEC R6P) .............................................. 2

Remote control ............................................................................... 1

Operating instructions .................................................................... 1

Specifications and the design are subject to possible modifications

without notice, due to improvements.

"DTS" ,"DTS-ES Extended Surround" and "Neo:6" are

trademarks of Digital Theater Systems, Inc.

Manufactured under license from Dolby Laboratories.

"Dolby", "Pro Logic" and the double D symbol are

trademarks of Dolby Laboratorories.

Amplifier Section

Continuous Power Output (STEREO mode)

Front ..................... 100 W per channel (DIN 1kHz, THD 1.0 %, 8

)

Continuous Power Output

Front ............................ 100 W per channel (1kHz, THD 1.0 %, 8

)

Center ............................................. 100 W (1kHz, THD 1.0 %, 8

)

Surround ..................... 100 W per channel (1kHz, THD 1.0 %, 8

)

· Above specifications are applicable when the power supply is

230V.

Input (Sensitivity/Impedance)

CD, VCR/DVR, CD-R/TAPE/MD, DVD/LD, TV/SAT ... 200 mV/47 k

Frequency Response

CD, VCR/DVR, CD-R/TAPE/MD, DVD/LD,

TV/SAT ...................................................... 5 Hz to 100,000 Hz

Output (Level/Impedance)

VCR/DVR REC, CD-R/TAPE/MD REC .................... 200 mV/2.2 k

Tone Control

BASS ......................................................................

± 6 dB (100 Hz)

TREBLE ..................................................................

± 6 dB (10 kHz)

LOUDNESS .................................... +9 dB/+9 dB (100 Hz/10 kHz)

Signal-to-Noise Ratio [DIN (Continuous rated power output/50 mW)]

CD, VCR/DVR, CD-R/TAPE/MD,DVD/LD, TV/SAT .................. 96 dB

Video Section

Input (Sensitivity/Impedance)

VCR/DVR, DVD/LD, TV/SAT ......................................... 1 Vp-p/75

Output (Level/Impedance)

VCR/DVR ...................................................................... 1 Vp-p/75

Frequency Response

VCR/DVR, DVD/LD,TV/SAT

] MONITOR ........ 5 Hz to 7 MHz dB

Signal-to-Noise Ratio .............................................................. 55 dB

FM Tuner Section

Frequency Range .......................................... 87.5 MHz to 108 MHz

Usable Sensitivity ...................... Mono:13.2 dBf, IHF (1.3

µV/ 75 )

50 dB Quieting Sensitivity ......................................... Mono: 20.2 dB

Stereo: 38.6 dBf

Signal-to-Noise Ratio ................................ Mono: 73 dB (at 85 dBf)

Stereo: 70 dB (at 85 dBf)

Signal-to-Noise Ratio (DIN) ......................................... Mono: 62 dB

Stereo: 58 dB

Distortion ........................................................ Stereo: 0.5 % (1 kHz)

Alternate Channel Selectivity ................................. 60 dB (400 kHz)

Stereo Separation ...................................................... 40 dB (1 kHz)

Frequency Response ................................. 30 Hz to 15 kHz (

±1 dB)

Antenna Input (DIN) .............................................. 75

unbalanced

AM Tuner Section

Frequency Range ........................................... 531 kHz to 1,602 kHz

Sensitivity (IHF, Loop antenna) ......................................... 350

µV/m

Selectivity ................................................................................ 25 dB

Signal-to-Noise Ratio .............................................................. 50 dB

Antenna ...................................................................... Loop antenna

Weight (without package)

1. SPECIFICATIONS