PIONEER VSX-D1011-G/FXJI - Service Manual Immediate Download

ORDER NO.

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.

PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium

PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936

PIONEER CORPORATION 2002

STANDBY/ON

MOVIE

MUSIC

MULTI JOG

ENTER

STEREO/DIRECT

MULTI CH IN

MASTER VOLUME

ACOUSTIC EQ

STANDBY

MULTI CHANNNEL

ACOUSTIC CALIBRATION

VSX-D2011

AUDIO/VIDEO MULTI-CHANNEL RECEIVER

PHONES

SPEAKERS

SIGNAL

SELECT

SB CH

MODE

EON

MODE

CHARACTER/

HI-BIT

HI-SAMPLING

SETUP

MIC

DIGITAL IN

S-VIDEO

VIDEO

VIDEO INPUT

AUDIO

SET UP

RETURN

TONE

TONE CONTROL

BASS/TREBLE

CLASS

BAND

STATION TUNING

MULTI JOG/ENTER

MULTI JOG CONTROL

SELECT

TUNER

EDIT

VSX-D2011-S

RRV2661

AUDIO/VIDEO MULTI-CHANNEL RECEIVER

VSX-D2011-S

VSX-D1011-S

VSX-D1011-K

THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).

*:Alter the wiring of the power-supply block at the primary winding of Power transformer referring to the Line Voltage Selection

described in Service Manual.

Model

Type

Porew Requirement

The voltage can be converted by the

following method.

VSX-D2011-S

HYXJI

AC220-230V

AC240V, *

VSX-D1011-S

HYXJI

AC220-230V

AC240V, *

VSX-D1011-K

HYXJI

AC220-230V

AC240V, *

For details, refer to "Important symbols for good services" .

T-ZZK AUG. 2002 printed in Japan

VSX-D2011-S

1234

123

SAFTY INFORMATION

This service manual is intended for qualified service technicians; it is not meant for the casual

do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been

trained to properly and safely repair complex products such as those covered by this manual.

Improperly performed repairs can adversely affect the safety and reliability of the product and may

void the warranty. If you are not qualified to perform the repair of this product properly and safely, you

should not risk trying to do so and refer the repair to a qualified service technician.

WARNING

This product contains lead in solder and cer tain electrical par ts contain chemicals which are known to the state of California to

cause cancer, bir th defects or other reproductive harm.

Health & Safety Code Section 25249.6 Proposition 65

NOTICE

(FOR CANADIAN MODEL ONLY)

Fuse symbols

(fast operating fuse)

and/or

(slow operating fuse) on PCB indicate that replacement

parts must be of identical designation.

REMARQUE

(POUR MODÈLE CANADIEN SEULEMENT)

Les symboles de fusible

(fusible de type rapide)

et/ou

(fusible de type lent) sur CCI indiquent que

les pièces de remplacement doivent avoir la même désignation.

ANY MEASUREMENTS NOT WITHIN THE

LIMITS OUTLINED ABOVE ARE INDICATIVE

OF A POTENTIAL SHOCK HAZARD AND

MUST BE CORRECTED BEFORE RETURN-

ING THE APPLIANCE TO THE CUSTOMER.

2. PRODUCT SAFETY NOTICE

Many electrical and mechanical parts in the appliance

have special safety related character istics. These are

often not evident

from visual

inspection nor the

protection afforded by them necessarily can be obtained

by using replacement components rated for voltage,

wattage, etc. Replacement par ts which have these

special safety character istics are identified in this

Service Manual.

Electr ical components having such features are

identified by marking with a

on the schematics and

on the parts list in this Service Manual.

The use of a substitute replacement component which

does not have the same safety characteristics as the

PIONEER recommended replacement one, shown in the

parts list in this Service Manual, may create shock, fire,

or other hazards.

Product Safety is continuously under review and new

instructions are issued from time to time. For the latest

infor mation, always consult the current PIONEER

Ser vice Manual. A subscription to, or

additional copies

of, PIONEER Ser vice Manual may be obtained at a

nominal charge from PIONEER.

(FOR USA MODEL ONLY)

1. SAFETY PRECAUTIONS

The following check should be perfor med for the

continued protection of the customer and ser vice

technician.

LEAKAGE CURRENT CHECK

Measure leakage current to a known ear th ground

(water pipe, conduit, etc.) by connecting a leakage

current tester such as Simpson Model 229-2 or

equivalent between the ear th ground and all exposed

metal par ts of the appliance (input/output ter minals,

screwheads, metal overlays, control shaft, etc.). Plug

the AC line cord of the appliance directly into a 120V

AC 60 Hz outlet and turn the AC power switch on. Any

current measured must not exceed 0.5 mA.

Device

under

test

Leakage

current

tester

Earth

ground

Reading should

not be above

0.5 mA

Also test with

plug reversed

(Using AC adapter

plug as required)

Test all

exposed metal

surfaces

AC Leakage Test

VSX-D2011-S

678

[ Important symbols for good services ]

In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely.

When you find the procedures bearing any of the symbols, be sure to fulfill them:

2. Adjustments

To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable.

In accordance with the procedures or instructions described in this manual, adjustments should be performed.

3. Cleaning

For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning,

proper cleaning should be performed to restore their performances.

5. Lubricants, glues, and replacement parts

Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying

glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the

prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed

ones should be used.

4. Shipping mode and shipping screws

To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or

the shipping screws should be installed before shipping out in accordance with this manual, if necessary.

1. Product safety

You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and

should keep the safety during servicing by following the safety instructions described in this manual.

VSX-D2011-S

1234

123

CONTENTS

SAFTY INFORMATION ....................................................................................................................................... 2

1. SPECIFICATIONS ............................................................................................................................................ 5

2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 6

2.1 PACKING ................................................................................................................................................... 6

2.2 EXTERIOR SECTION................................................................................................................................ 8

2.3 REAR PANEL SECTION.......................................................................................................................... 10

2.4 HEAT SINK SECTION.............................................................................................................................. 12

2.5 FRONT PANEL SECTION ....................................................................................................................... 14

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ..........................................................................................16

3.1 AUDIO BLOCK DIAGRAM ....................................................................................................................... 16

3.2 DSP BLOCK DIAGRAM........................................................................................................................... 18

3.3 VIDEO BLOCK DIAGRAM ....................................................................................................................... 20

3.4 POWER AMP BLOCK DIAGRAM ............................................................................................................ 21

3.5 OVERALL WIRING DIAGRAM................................................................................................................. 22

3.6 FM/AM TUNER MODULE ........................................................................................................................ 24

3.7 7.1CH I/O, V-AUDIO IN, FRONT IN and OPTICAL IN ASSYS ................................................................ 26

3.8 INPUT CONNECT and COAXIAL IN ASSYS ..........................................................................................28

3.9 VIDEO ASSY ........................................................................................................................................... 30

3.10 COMPONENT and MECHA SW ASSYS ...............................................................................................32

3.11 MAIN CONTROL ASSY (1/3)................................................................................................................. 34

3.12 MAIN CONTROL ASSY (2/3)................................................................................................................. 36

3.13 MAIN CONTROL ASSY (3/3)................................................................................................................. 38

3.14 MIC & F.OPT IN, MIC AMP and DSP CONNECTION ASSYS .............................................................. 40

3.15 POWER AMP IN, FAN DRIVE and FAN CONNECTION ASSYS .......................................................... 42

3.16 DSP ASSY (1/2)..................................................................................................................................... 44

3.17 DSP ASSY (2/2)..................................................................................................................................... 46

3.18 DISPLAY ASSY...................................................................................................................................... 48

3.19 VOLUME, MULTI JOG and HEADPHONE ASSYS................................................................................ 50

3.20 REGULATOR ASSY............................................................................................................................... 52

3.21 POWER AMP-L ASSY ........................................................................................................................... 54

3.22 POWER AMP-R and POWER AMP-C ASSYS ...................................................................................... 56

3.23 SP/PS, DIODE, TRANS 2-1 and VH TR ASSYS....................................................................................58

3.24 TRANS 2-2, TRANS 1 and PRIMARY ASSYS.......................................................................................60

4. PCB CONNECTION DIAGRAM ..................................................................................................................... 62

4.1 FM/AM TUNER MODULE ........................................................................................................................ 63

4.2 7.1CH I/O ASSY ...................................................................................................................................... 64

4.3 V-AUDIO IN ASSY.................................................................................................................................... 65

4.4 FRONT IN, OPTICAL IN and INPUT CONNECT ASSYS........................................................................ 66

4.5 COAXIAL IN ASSY .................................................................................................................................. 68

4.6 VIDEO ASSY ........................................................................................................................................... 69

4.7 MAIN CONTROL ASSY ........................................................................................................................... 70

4.8 MIC & F. OPT IN, MIC AMP and DSP CONNECTION ASSYS ............................................................... 74

4.9 POWER AMP IN ASSY............................................................................................................................ 76

4.10 FAN DRIVE and FAN CONNECTION ASSYS ....................................................................................... 77

4.11 DSP ASSY ............................................................................................................................................. 78

4.12 MECHA SW, DISPLAY, VOLUME, MULTI JOG and HEADPHONE ASSYS.......................................... 80

4.13 REGULATOR and COMPONENT ASSYS ............................................................................................. 84

4.14 POWER AMP L and POWER AMP C ASSYS ....................................................................................... 88

4.15 POWER AMP R ASSY........................................................................................................................... 92

4.16 SP/PS ASSY .......................................................................................................................................... 96

4.17 DIODE, TRANS 2-1 and VH TR ASSYS ................................................................................................ 98

4.18 TRANS 2-1, TRANS 1 and PRIMARY ASSYS..................................................................................... 100

5. PCB PARTS LIST ......................................................................................................................................... 102

6. ADJUSTMENT ............................................................................................................................................. 113

7. GENERAL INFORMATION ........................................................................................................................... 114

7.1 DIAGNOSIS ........................................................................................................................................... 114

7.1.1 PROTECTION CIRCUIT CONTROL SPECIFICATION ...................................................................... 114

7.1.2 DIAGNOSTICS OF AMPLIFIER SECTION ........................................................................................ 116

7.1.3 TROUBLE SHOOTING ....................................................................................................................... 117

7.1.4 DISASSEMBLY ................................................................................................................................... 122

7.2 PARTS.................................................................................................................................................... 125

7.2.1 IC ........................................................................................................................................................ 125

7.2.2 DISPLAY ............................................................................................................................................. 139

7.3 CLEANING............................................................................................................................................. 141

8. PANEL FACILITIES ...................................................................................................................................... 143

VSX-D2011-S

678

1. SPECIFICATIONS

VIDEO Section (Composite)

Input (Sensitivity/Impedance)

VCR 1/DVR, VCR 2, VIDEO, DVD/LD,

TV/SAT ...................................................................... 1 Vp-p/75

Output (Level/Impedance)

VCR 1/DVR, VCR 2, MONITOR OUT,

MONITOR OUT2 ....................................................... 1 Vp-p/75

Frequency Response

VCR 1/DVR, VCR 2, TV/SAT, DVD/LD

VIDEO

=MONITOR OUT, ........................... 5 Hz to 10 MHz dB

Signal-to-Noise Ratio .............................................................. 65 dB

FM Tuner Section

Frequency Range .......................................... 87.5 MHz to 108 MHz

Usable Sensitivity ....................... Mono: 15.2 dBf, IHF (1.6

µV/75 )

50 dB Quieting Sensitivity ........................................ Mono: 20.2 dBf

Stereo: 41.2 dBf

Sensitivity (DIN) ...................................... Mono: 1.1

µV (S/N 26 dB)

Stereo: 50

µV (S/N 46 dB)

Signal-to-Noise Ratio ................................. Mono: 76 dB (at 85 dBf)

Stereo: 72 dB (at 85 dBf)

Signal-to-Noise Ratio (DIN) ........................................ Mono: 62 dB

Stereo: 58 dB

Distortion ........................................................ Stereo: 0.6 % (1 kHz)

Alternate Channel Selectivity ................................. 70 dB (400 kHz)

Stereo Separation ...................................................... 40 dB (1 kHz)

Frequency Response ................................ 30 Hz to 15 kHz (

± 1 dB)

Antenna Input ........................................................ 75

unbalanced

AM Tuner Section

Frequency Range ........................................... 531 kHz to 1,602 kHz

Sensitivity (IHF, Loop antenna) ......................................... 350

µV/m

Selectivity ................................................................................ 30 dB

Signal-to-Noise Ratio .............................................................. 50 dB

Antenna ...................................................................... Loop antenna

Miscellaneous

Power Requirements ................................ AC 220 - 230 V, 50/60 Hz

Power Consumption ............................................................... 600 W

Power Consumption in Standby mode .................................... 0.7 W

AC Outlets

SWITCHED ................................................... 100 W (0.8A) MAX.

Dimensions .................................. 420 (W)

× 188 (H) × 464 (D) mm

Weight (without package) (VSX-D2011)................................ 19.6 kg

Weight (without package) (VSX-D1011)................................ 18.2 kg

Furnished Parts

FM Wire Antenna ........................................................................... 1

AM Loop Antenna .......................................................................... 1

"AA" IEC LR6 batteries ................................................................... 4

Remote Control Unit ...................................................................... 1

Microphone for Auto Surround Sound Setup ................................. 1

Microphone Stand for Auto Surround Sound Setup ....................... 1

Operating Instructions .................................................................... 1

NOTE:

Specifications and the design are subject to possible

modifications without notice, due to improvements.

Amplifier Section

Continuous Power Output (DIN)

FRONT .......................... 100 W + 100 W (DIN 1 kHz, THD 1 %, 8

)

CENTER ..................................... 100 W (DIN 1 kHz, THD 1 %, 8

)

SURROUND ......................................................... 100 W + 100 W

(DIN 1 kHz, THD 1 %, 8

)

SURROUND BACK .............................................. 100 W + 100 W

(DIN 1 kHz, THD 1 %, 8

)

Rated Power Output ................................................. 100 W + 100 W

(20 Hz 20 kHz, 0.09 %, 8

)

Input (Sensitivity/Impedance)

PHONO MM (VSX-D2011)..................................... 4.7 mV/47 k

VCR 1/DVR, VCR 2, DVD/LD, TV/SAT, VIDEO, CD,

CD-R/TAPE 1, MD/TAPE 2 .................................... 335 mV/47 k

Frequency Response

PHONO MM (VSX-D2011)............... 20 Hz to 20,000 Hz

± 0.3 dB

VCR 1/DVR, VCR 2, DVD/LD, TV/SAT, VIDEO, CD,

CD-R/TAPE 1, MD/TAPE 2 ................... 5 Hz to 100,000 Hz

Output (Level/Impedance)

VCR 1/DVR REC, VCR 2 REC, CD-R/TAPE 1 REC,

MD/TAPE 2 REC ................................................. 335 mV/2.2 k

Tone Control

BASS ...................................................................

± 6 dB (100 Hz)

TREBLE ..............................................................

± 6 dB (10 kHz)

LOUDNESS ........................................ +4/+2 dB (100 Hz/10 kHz)

(at volume position -40dB)

Signal-to-Noise Ratio (IHF, short circuited, A network)

VCR 1/DVR, VCR 2, DVD/LD, TV/SAT, VIDEO, CD,

CD-R/TAPE 1, MD/TAPE 2, MULTI CH IN ........................ 101 dB

Signal-to-Noise Ratio

[DIN (Continuous rated power output/50 mW)]

VCR 1/DVR, VCR 2, DVD/LD, TV/SAT, VIDEO, CD,

CD-R/TAPE 1, MD/TAPE 2 ............................................. 92/65 dB

VIDEO Section (S jack)

Input (Sensitivity/Impedance)

VCR 1/DVR, VCR 2, VIDEO, DVD/LD, TV/SAT

Luminance signal (Y) ............................................. 1 Vp-p/75

Chrominance signal (C) .................................. 0.286 Vp-p/75

Output (Level/Impedance)

VCR 1/DVR, VCR 2, MONITOR OUT

Luminance signal (Y) ............................................. 1 Vp-p/75

Chrominance signal (C) .................................. 0.286 Vp-p/75

Frequency Response

VCR 1/DVR, VCR 2, VIDEO, DVD/LD, TV/SAT

Luminance signal (Y) ............................... 5 Hz to 10 MHz

Signal-to-Noise Ratio

Luminance signal (Y) ....................................................... 65 dB

Component Video Section (VSX-D2011)

Input (Sensitivity)

Y .............................................................................. 1 Vp-p/75

PB/PR ........................................................................... 0.7 V/75

Output (Level/Impedance)

Y .............................................................................. 1 Vp-p/75

PB/PR ........................................................................... 0.7 V/75

Frequency Response

Y ................................................................ 5 Hz to 40 MHz

PB/PR ........................................................... 5 Hz to 40 MHz

"DTS", "DTS-ES Extended Surround" and "Neo:6" are

trademarks of Digital Theater Systems, Inc.

Lucasfilm and THX are trademarks or registered

trademarks of Lucasfilm, Ltd. & TM. Surround EX is

a jointly developed technology of THX and Dolby

Laboratories, and is a trademark of Dolby

authorization.

Manufactured under license from Dolby Laboratories.

"Dolby", "Pro Logic", "Surround EX" and double-D

symbol are trademarks of Dolby Laboratories