PIONEER S-W3700-K/XTW/UC - Owner's Manual Immediate Download

S-FCR4700

S-FCR3700

S-W3700-K

OPERATING GUIDE

SPEAKER SYSTEM

WHAT'S IN THE BOX

· S-FCR4700

· Non-skid pads (small) x 4

· Non-skid pads (large) x 16

· Surround speakers x 2

· Front speakers x 2

· Center speaker

· Speaker cords x 5

Front right (Red)

Surround right (Grey)

Surround left (Blue)

Front left (White)

Center (Green)

· Speaker stand bases x 4

· Screws x 12

· S-FCR3700

· Front speakers x 2

· Non-skid pads (small) x 12

· Non-skid pads (large) x 8

· Surround speakers x 2

· Center speaker

· Speaker cords x 5

Front right (Red)

Surround right (Grey)

Surround left (Blue)

Front left (White)

Center (Green)

· Speaker stand bases x 2

· Screws (for bases) x 6

· Screws

(for speaker stand) x 2

· Speaker stands x 2

IMPORTANT:

The serial number for this equipment is located on the side of

the packing case. Please write this serial number on the

warranty page and keep it in a secure area for future reference.

· S-W3700-K

· Subwoofer

· Operating guide

· Non-skid pads (large) x 4

· Speaker cord

Subwoofer (Purple)

INSTALLATION PRECAUTIONS

FRONT / CENTER / SURROUND SPEAKERS

· Do not install these units near a stove or other heating

appliance, or put them in a place exposed to the sun. Such

locations may cause the cabinet to change color and the

speaker system to break down.

· The front, center and surround speakers supplied with this

system are magnetically shielded. However, placing them

extremely close to a television may result in color distortion

on the screen. If this happens, move the speakers a little further

away and switch off the television for 15 to 30 minutes.

SUBWOOFER

· Do not place anything on top of the cabinet.

· Do not spill liquid on the cabinet.

· Place the subwoofer at least 8 inches (20 cm) from any wall

or curtain in order to avoid heat build-up.

· The subwoofer is not magnetically shielded and so should

not be placed near a TV or monitor. Magnetic storage media

(such as floppy discs and tape or video cassettes) should also

not be kept close to the subwoofer.

BEFORE USE

· Thank you for buying this Pioneer product.

· Please read through this operating guide before using your

speaker system to optimize performance.

FRONT / CENTER / SURROUND SPEAKERS

In order to prevent damage to the speaker system resulting from

input overload, please observe the following precautions:

· When connecting or disconnecting cables, be sure amplifier

power is OFF.

· Do not use excessive amplifier volume if using a tone control

to emphasize high or low frequencies.

http://www.pioneerelectronics.com

PLACEMENT AND FINE TUNING

SUBWOOFER

Sound spreads in all directions in the very low frequency range.

Human hearing cannot easily detect the source of very low

frequencies. Be sure to provide a space of at least 8 inches

(20cm) between the rear of the subwoofer and the nearest wall.

FRONT SPEAKERS

For best results the loudspeakers should be separated a distance

approximately equal to the listening distance. Angling the

loudspeakers inward towards the listener will improve the image

stability for non-central listeners. Close proximity to a side or

rear wall will enhance the midbass performance, although too

close (particularly a corner location) and the bass may be

unnaturally high and image performance may be degraded.

CENTER SPEAKER

The loudspeaker should be positioned below the TV. For best

results align the front of the loudspeaker with the front of the TV. If

the loudspeaker is placed under the TV and very close to the

floor, then tilting upwards may be beneficial.

When installing the center speaker on top of the TV, be sure to

secure it with tape or some other suitable means. Otherwise, the

speaker may fall from the TV due to external shocks such as

earthquakes, endangering those nearby or damaging the speaker.

SURROUND SPEAKERS

For best results the loudspeaker should be positioned near ear

level (S-FCR3700 only).

STANDARD SURROUND SETUP

This is a standard multichannel surround sound speaker setup

for optimal 5.1 channel home theater sound.

CAUTION:

· Do not connect this speaker to any amplifier other than

the one supplied with this system. Connection to any other

amplifier may result in a malfunction or a fire.

· Do not attach the subwoofer, front and surround speakers

to the wall or ceiling. They may fall off and cause injury (S-

FCR4700 only).

· Do not attach the subwoofer and front speakers to the

wall or ceiling. They may fall off and cause injury

(SFCR3700 only).

CONNECTING YOUR SYSTEM

IMPORTANT:

Make sure all equipment is turned off before making any

connections.

FRONT / CENTER / SURROUND / SUBWOOFER

SPEAKERS

Correct wiring of your loudspeakers is essential for achieving

the best sound quality. Be careful to ensure proper polarity of

connection.

Twist and pull off the protective shields on each wire.

Connect to the speaker terminals on the rear of the

receiver.

To connect, insert the colored wire into the matching positive

(colored) terminal and the other wire into the negative (black)

terminal as shown below.

Note that the color-coded tabs are as follows:

· Red : Front right (R)

· Purple : Subwoofer

· White : Front left (L)

· Grey : Surround right (R)

· Green : Center speaker

· Blue : Surround left (L)

Colored marker

WARNING:

Handling the cord on this product or cords associated with

accessories sold with the product will expose you to

chemicals listed on proposition 65 known to the State of

California and other governmental entities to cause cancer

and birth defect or other reproductive harm.

Wash hands after handling

Front left

Surround

left

Listening position

Center

Subwoofer

Front right

Surround

right

Connect to the speaker terminals on the rear of the

speakers.

Match the colored wire with the color-coded label (above the

tabs), then insert the colored wire into the red (+) tab and the

other wire with the black () tab.

Colored marker

red

black

Assembling the speaker stand bases and securing

your front and surround (S-FCR4700 only)

speakers

Attach the speaker stand bases to the stems using the screws

provided.

Once you have aligned the stem and base, secure with the small

screws at the points shown below. Note that the speaker should

face in the direction of the base of the isosceles triangle (outlined

below).

Secure each of the front and surround (S-FCR4700 only)

speakers using the plastic catch provided.

Screw two picture hooks or similar into the wall behind the

speaker. Pass a cord around the hooks and through the plastic

catch so that the speaker is stabilized (make sure to test that it

supports the weight of the speaker).

After installing, make sure the speaker is securely fixed.

Rear

Front

Sufficiently thick

cord (not supplied)

Plastic catch

CAUTION:

· The plastic catch is not a mounting fixture, and the speaker

should not be hung directly from the wall using this catch.

Always use a cord when stabilizing the speaker.

· Pioneer disclaims all responsibility for any losses or

damage resulting from improper assembly, installation,

insufficient strength of the installation materials, misuse,

or natural disasters.

NON-SKID PADS

Attach the small non-skid pads to the base of the surround (S-

FCR3700 only) and center speakers. The large non-skid pads

are for the front and surround (S-FCR4700 only) speakers, and

the subwoofer (as shown).

Use the adhesive side of the pads to attach them to the base of

each speaker and the subwoofer.

If you choose to use speaker stands with the surround speakers,

attach the non-skid pads to the stand bases instead of to the

underside of the speakers (S-FCR3700 only).

Small non-skid pads

Surround speakers

(S-FCR3700 only)

Center speaker

Speaker stands

(S-FCR3700 only)

Large non-skid pads

Front and Surround

(S-FCR4700 only) speakers

Subwoofer

OPTIONALLY, ATTACH THE SURROUND SPEAKERS

TO THE SPEAKER STANDS (S-FCR3700 ONLY)

For each speaker,line up the spurs on the stand with the holes

on the back of the speaker and insert, then secure the speaker

to the stand with the screw provided.

WALL MOUNTING THE SURROUND (S-

FCR3700 ONLY) AND CENTER SPEAKERS

The surround (S-FCR3700 only) and center speakers have

mounting holes which can be used to mount the speaker on the

wall.

3/16 in. to 1/4 in.

(5 mm to 7 mm)

3/16 in.

(5 mm)

3/8 in.

(10 mm)

Mounting screw

(not supplied)

Before mounting (see above), keep in mind the following points:

· Remember that the speaker system is heavy and that its weight

could cause the screws to work loose, or the wall material to

fail to support it, resulting in the speaker falling.

Make sure that the wall you intend to mount the speakers on

is strong enough to support them. Do not mount on plywood

or soft surface walls.

· Mounting screws are not supplied. Use screws suitable for

the wall material and support the weight of the speaker.

CAUTION:

· If you are unsure of the qualities and strength of the walls,

consult a professional for advice.

· Pioneer is not responsible for any accidents or damage

that result from improper installation.

TROUBLESHOOTING

SYMPTOM

PROBABLE CAUSE

REMEDY

1. No sound

·Bad speaker wire or connection

·Receiver is off

·Volume control is at zero

· Connect correctly or replace wire

·Turn on receiver

· Slowly turn up volume

2. Sound is distorted

·Extreme signal condition

·Turn down the amplifier's output level

(volume, bass control, bass boost) to

lower the level.

SPECIFICATIONS

FRONT SPEAKERS (S-FCR4700,S-FCR3700)

SURROUND SPEAKERS (S-FCR4700)

Enclosure ................................... Closed-box floorstanding type

(magnetically shielded)

System .................................................................. 2-way system

Speakers:

Woofer .................................................. 7.7 cm cone type x 2

Tweeter ............................................. 2.6 cm semi-dome type

Nominal impedance .............................................................. 8

Frequency range .............................................. 70 Hz to 20 kHz

Dimensions ......... 260 mm (W) x 1096.5 mm (H) x 260 mm (D)

10 1/4 in. (W) x 43 3/16 in. (H) x 10 1/4 in. (D)

Weight .............................................................. 4.2 kg / 9 lb 4 oz

SURROUND SPEAKERS (S-FCR3700)

Enclosure ......................................... Closed-box bookshelf type

(magnetically shielded)

System ...................................................... 7.7 cm 1-way system

Speakers ......................................................... 7.7 cm cone type

Nominal impedance .............................................................. 8

Frequency range .............................................. 80 Hz to 20 kHz

Dimensions ................ 100 mm (W) x 136 mm (H) x 80 mm (D)

3 15/16 in. (W) x 5 3/8 in. (H) x 3 1/8 in. (D)

Weight ............................................................ 0.55 kg / 1 lb 3 oz

CENTER SPEAKER (S-FCR4700,S-FCR3700)

Enclosure ......................................... Closed-box bookshelf type

(magnetically shielded)

System ...................................................... 7.7 cm 1-way system

Speakers ......................................................... 7.7 cm cone type

Nominal impedance .............................................................. 8

Frequency range .............................................. 75 Hz to 20 kHz

Dimensions .................. 270 mm (W) x 96 mm (H) x 90 mm (D)

10 5/8 in. (W) x 3 3/4 in. (H) x 3 9/16 in. (D)

Weight .......................................................... 0.78 kg / 1 lb 12 oz

SUBWOOFER (S-W3700-K)

Enclosure .................................................. Bass-reflex floor type

System ....................................................... 16 cm 1-way system

Speaker ........................................................... 16 cm cone type

Nominal impedance ............................................................. 8

Frequency range ................................................ 30 Hz to 2 kHz

Dimensions .............. 190 mm (W) x 360 mm (H) x 320 mm (D)

7 1/2 in. (W) x 14 3/16 in. (H) x 12 5/8 in. (D)

Weight ............................................................. 4.0 kg/ 8 lb 13 oz

ACCESSORIES

Speaker cords

(S-FCR4700,S-FCR3700) .................................................... 5

(S-W3700-K) ......................................................................... 1

Non-skid pads (For subwoofer) (S-W3700-K) ......................... 4

Non-skid pads (Large) (For speaker stand bases)

(S-FCR3700) ........................................................................ 8

(S-FCR4700) ...................................................................... 16

Non-skid pads (Small)

(For center and surround speakers) (S-FCR3700) ........... 12

(For center speaker) (S-FCR4700) ...................................... 4

Speaker stands (For surround speakers) (S-FCR3700) ......... 2

Screws (For speaker stands) (S-FCR3700) ............................ 2

NOTE: Specifications and design subject to possible

modification without notice due to improvements.

Published by Pioneer Corporation.

CABINET MAINTENANCE

Use a polishing cloth or dry cloth to wipe off dust and dirt.

When the cabinet is very dirty, clean with a soft cloth dipped in

some neutral cleanser diluted five or six times with water, and

then wipe again with a dry cloth. Do not use furniture wax or

cleaners.

Never use thinners, benzine, insecticide sprays and other

chemicals on or near the cabinets, since these will corrode the

surfaces.

Selecting fine audio equipment such as the unit you've just

purchased is only the start of your musical enjoyment. Now it's

time to consider how you can maximize the fun and excitement

your equipment offers. This manufacturer and the Electronic

Industries Association's Consumer Electronics Group want you

to get the most out of your equipment by playing it at a safe level.

One that lets the sound come through loud and clear without

annoying blaring or distortion-and, most importantly, without

affecting your sensitive hearing.

Sound can be deceiving. Over time your hearing "comfort

level" adapts to higher volumes of sound. So what sounds

"normal" can actually be loud and harmful to your hearing. Guard

against this by setting your equipment at a safe level BEFORE

your hearing adapts.

To establish a safe level:

· Start your volume control at a low setting.

· Slowly increase the sound until you can hear it comfortably

andclearly, and without distortion.

Once you have established a comfortable sound level:

· Set the dial and leave it there.

Taking a minute to do this now will help to prevent hearing

damage or loss in the future. After all, we want you listening for

a lifetime.

We Want You Listening ForA Lifetime

Used wisely, your new sound equipment will provide a lifetime

of fun and enjoyment. Since hearing damage from loud noise is

often undetectable until it is too late, this manufacturer and the

Electronic Industries Association's Consumer Electronics Group

recommend you avoid prolonged exposure to excessive noise.

This list of sound levels is included for your protection.

Information courtesy of the Deafness Research Foundation.

Subway, motorcycle, truck traffic, lawn mower

100

Garbage truck, chain saw, pneumatic drill

120

Rock band concert in front of speakers, thunderclap

140

Gunshot blast, jet plane

180

Rocket launching pad

THE FOLLOWING NOISES CAN BE DANGEROUS

UNDER CONSTANT EXPOSURE

Quiet library, soft whispers

Living room, refrigerator, bedroom away from traffic

Light traffic, normal conversation, quiet office

Air conditioner at 20 feet, sewing machine

Vacuum cleaner, hair dryer, noisy restaurant

Average city traffic, garbage disposals, alarm clock

at two feet.

Decibel

Level

Example