ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2006
S-W1EX
RRV3274
POWERED SUBWOOFER
S-W1EX
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model
Type
Porew Requirement
Remarks
S-W1EX
LFXTW
AC 110V
S-W1EX
MLTXTW
AC 220-230V
For details, refer to "Important Check Points for Good Servicing".
T-ZZS JAN. 2006 printed in Japan
S-W1EX
2
12
34
12
3
4
C
D
F
A
B
E
SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual
do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trained to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to
cause cancer, bir th defects or other reproductive harm.
Health & Safety Code Section 25249.6 Proposition 65
NOTICE
Fuse symbols
(fast operating fuse)
and/or
(slow operating fuse) on PCB indicate that replacement
parts must be of identical designation.
REMARQUE
Les symboles de fusible
(fusible de type rapide)
et/ou
(fusible de type lent) sur CCI indiquent que
les pièces de remplacement doivent avoir la même désignation.
ANY MEASUREMENTS NOT WITHIN THE
LIMITS OUTLINED ABOVE ARE INDICATIVE
OF A POTENTIAL SHOCK HAZARD AND
MUST BE CORRECTED BEFORE RETURN-
ING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related character istics. These are
often not evident
from visual
inspection nor the
protection afforded by them necessarily can be obtained
by using replacement components rated for voltage,
wattage, etc. Replacement parts which have these
special safety characteristics are identified in this
Service Manual.
Electrical components having such features are
identified by marking with a
on the schematics and
on the parts list in this Service Manual.
The use of a substitute replacement component which
does not have the same safety characteristics as the
PIONEER recommended replacement one, shown in the
parts list in this Service Manual, may create shock, fire,
or other hazards.
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER
Service Manual. A subscription to, or
additional copies
of, PIONEER Service Manual may be obtained at a
nominal charge from PIONEER.
(FOR USA MODEL ONLY)
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service
technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground
(water pipe, conduit, etc.) by connecting a leakage
current tester such as Simpson Model 229-2 or
equivalent between the earth ground and all exposed
metal parts of the appliance (input/output terminals,
screwheads, metal overlays, control shaft, etc.). Plug
the AC line cord of the appliance directly into a 120V
AC 60 Hz outlet and turn the AC power switch on. Any
current measured must not exceed 0.5 mA.
Device
under
test
Leakage
current
tester
Earth
ground
Reading should
not be above
0.5 mA
Also test with
plug reversed
(Using AC adapter
plug as required)
Test all
exposed metal
surfaces
AC Leakage Test
S-W1EX
3
56
78
56
7
8
C
D
F
A
B
E
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
0 Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.
S-W1EX
4
12
34
12
3
4
C
D
F
A
B
E
CONTENTS
SAFETY INFORMATION ..................................................................................................................................... 2
1. SPECIFICATIONS ............................................................................................................................................ 5
2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 6
2.1 PACKING ................................................................................................................................................... 6
2.2 EXTERIOR SECTION................................................................................................................................ 8
2.3 SPEAKER SECTION ............................................................................................................................... 10
2.4 AMPLIFIER ASSY ................................................................................................................................... 12
3. SCHEMATIC DIAGRAM ................................................................................................................................. 14
3.1 OVERALL WIRING DIAGRAM................................................................................................................. 14
3.2 INPUT, CONTROL, MODE and LED ASSYS ..........................................................................................16
3.3 D AMP ASSY ........................................................................................................................................... 18
3.4 POWER SW and SMPS ASSYS.............................................................................................................. 20
4. PCB CONNECTION DIAGRAM ..................................................................................................................... 23
4.1 INPUT ASSY............................................................................................................................................ 24
4.2 CONTROL, MODE and LED ASSYS....................................................................................................... 26
4.3 D AMP ASSY ........................................................................................................................................... 28
4.4 POWER SW and SMPS ASSYS.............................................................................................................. 30
5. PCB PARTS LIST ........................................................................................................................................... 34
6. ADJUSTMENT ............................................................................................................................................... 39
7. GENERAL INFORMATION ............................................................................................................................. 40
7.1 CAUTIONS ON SERVICING AMP ASSY (AXW7007, AXW7008) .......................................................... 40
7.2 SMPS BLOCK TROUBLE SHOOTING .................................................................................................... 42
7.3 AMP BLOCK TROUBLE SHOOTING ...................................................................................................... 44
7.4 DESCRIPTION OF SMPS BLOCK .......................................................................................................... 45
7.5 DESCRIPTION OF AMP BLOCK............................................................................................................. 47
7.6 CAUTIONS ON DISASSEMBLY AND ASSEMBLY .................................................................................. 48
8. PANEL FACILITIES ........................................................................................................................................ 51
S-W1EX
5
56
78
56
7
8
C
D
F
A
B
E
1. SPECIFICATIONS
Accessories
· Power cable
(ADG7097: /LF)
· Power cable
(ADG1154: /MLT)
· Spikes (x4)
(SBA6019)
· Operating Instructions (SRD6032: /LF)
(SRD6031: /MLT)
· Bases (x4)
(SEA6039)
· Ground cord
(SDF6004)
· RCA plug cord
(SDE6001)
Cabinet ........... Floor type with PASSIVE RADIATOR system
(Magnetically shielded)
Woofer ...................................................... 30 cm cone type
PASSIVE RADIATOR .............................. 30 cm cone type
Frequency response .............. 25 - 4,000Hz(set to BYPASS)
Power Amplifier Continuous Power Output (RMS)
........................................................... 250 W/4
(100 Hz)
Input (sensitivity at 100 Hz/ impedance)
SPEAKER LEVEL ............................ 1.6 V + 1.6 V/15 k
(both channels in-phase)
LINE LEVEL (RCA jack) ............................. 160 mV/50 k
Output (Level at 100 Hz/ impedance)
LINE LEVEL (RCA jack) ............................... 160 mV/1 k
CROSSOVER Frequency
..................................... 50 - 150 Hz (continuously variable)
Outline Dimension .......... 430 (W) x 480 (H) x 430 (D) mm
Weight (without package) ........................................ 34.5 kg
Power Requirements (MLTXTW)
220 - 230 V~, 50/60 Hz
Power Requirements (LFXTW)
110V~, 50/60 Hz
Power Consumption .................................................. 56 W
Accessories ...................................................... Spikes x 4
Bases x 4
RCA plug cord x 1
Power cable x 1
Ground cord x 1
Operating instructions x 1
NOTE:
Specifications and design subject to possible
modification without notice, due to improvements.
is a trademark placed on a product with
Pioneer's Phase Control Technology.
The Technology enables high-grade 5.1ch
with no delay in the bass area.
Above specifications are for when power supply is 230 V.
·
This speaker system is magnetically shielded.
However, depending on the installation location,
color distortion may occur if the speaker system is
installed extremely close to the screen of a television
set.
If this happens, turn off the power switch of the
television set, and turn it on after 15 to 30 minutes.
If the problem persists, place the speaker system
away from the television set.
*
Maunfactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks of Dolby
Laboratories.