ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2007
Center
Surround
Front
S-DV4T
RRV3654
SPEAKER SYSTEM
S-DV4T
XCN5
T-ZZR AUG. 2007 Printed in Japan
S-DV4T
2
12
3
4
12
3
4
C
D
F
A
B
E
1. REASSEMBLY AND DISASSEMBLY PRECAUTIONS
Rear
Front
Stem
(the bottom of cabinet)
Speaker Stand Base
GRILLE
The grille is attached to the cabinet by its bosses applied with
adhesive. To detach it, pry it open by inserting a flat blade
screwdriver into lower right and lower left slot. To attach it,
apply adhesive to the holes on the baffle. Then press it to the
baffle.
CAUTION
There are 10 bosses for press-fitting at the grille. To detach the
grille, remove in order from lower bosses. (Refer to the figure
in page 4.) In order not to damage the bosses, don't remove it
forcibly. Pry it open little by little. Be sure to insert a flat blade
screwdriver from just beside of its bosses.
WOOFER
The woofer is attached to the baffle by 4 external screws.
To detach it, unfasten those screws. To detach it, first remove
the grille. Then remove the screws. When attaching it, face its
terminal downward.
TWEETER
The tweeter is attached to the baffle by 3 external screws. To
detach it, unfasten those screws. To detach it, first remove the
grille. Then remove the screws. When attaching it, face its ter-
minal leftward and rightward.
COSMETIC PANEL
The cosmetic panel is attached to the baffle by its bosses. To
detach it, pry it open by inserting a flat blade screwdriver into
lower slot. To detach it, first remove the speaker stand base and
grille. Then remove the cosmetic panel. When attaching it, fit
the boss into the hole on the baffle.
GRILLE
The grille assy is attached to the cabinet by 8 external screws.
To detach it ,unfasten those screws.
SPEAKER UNIT
The speaker unit, together with the grille assy, is attached to the
cabinet by 4 external screws. To detach it, first remove the
grille assy. Next remove the cabinet. Then remove the cable.
When attaching it, face its terminal toward the left ward.
SPEAKER STAND BASES
The speaker stand base is attached to the bottom of cabinet by 3
external screws. To detach it, unfasten those screws.Attach the
speaker stand bases to the stems using the screws provided.
Once you have aligned the stem and base, secure with the small
screws at the points shown below. Note that the speaker should
face in the direction of the base of the isosceles triangle (out-
lined below).
1.1 FRONT, SURROUND SPEAKER
1.2 CENTER SPEAKER
S-DV4T
3
56
7
8
56
7
8
C
D
F
A
B
E
2. EXPLODED VIEWS AND PARTS LIST
2.1 PACKING
PACKING Parts List
NOTES : · Parts marked by " NSP " are generally unavailable because they are not in our Master Spare Parts List.
· The
> mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Tape
Tape
Mark No.
Description
Part No.
NSP 1
CS Assy (Front, Surround )
SMW6253
NSP 2
CS Assy (Center )
SMW6259
3
Speaker Cord (FL: White)
SDS1174
4
Speaker Cord (FR: Red)
SDS1175
5
Speaker Cord (SL: Blue)
SDS1176
6
Speaker Cord (SR: Gray)
SDS1177
7
Speaker Cord (C: Green)
SDS1178
8
Screw (for Speaker Stand Base) CYC40P300FTC
9
Polyethylene Bag S (for Screw) SHL1314
10
Non Skid Pad
SEP6014
(for Speaker Stand Base)
12
Polyethylene Bag
SHL1251
(for Accessory set)
13
Polyethylene Bag S2 (for Center) SHL1417
14
Speaker Stand Base
SMS6031
15
Protector (Top, Bottom)
SHA6140
16
Protector (Top, Bottom)
SHA6141
17
Protector (Middle)
SHA6142
18
Protector (Middle)
SHA6143
19
Protection Sheet
SHC6051
20
Polyethylene Bag S3
SHL1427
(for Speaker Stand Base)
21
Polyethylene Bag S2 (for Front) SHL6078
22
Packing Case
SHG6306
Mark No.
Description
Part No.
S-DV4T
4
12
3
4
12
3
4
C
D
F
A
B
E
2.2 SPEAKER SYSTEM (FRONT, SURROUND)
SPEAKER SYSTEM (FRONT, SURROUND) Parts List
Speaker Stand Base
( refer to 2.1 PACKING
/ No.14 )
Screw
( refer to 2.1 PACKING
/ No.8 Screw )
Non Skid Pad( refer to 2.1 PACKING / No.10 Non Skid Pad )
Model Label
: the attached to
the applied with
adhesive.
Mark No.
Description
Part No.
1
Grille
SMG6122
2
Cosmetic Plate Assy
SXB6009
3
Input Terminal
SKX1060
4
Fastener
SNB6003
5
Network Assy
SWN6020
6
Speaker (Woofer)
K77DC55-51F
7
Speaker (Tweeter)
FK26AP32-51F
8
Screw (for Tweeter)
BYC35P160FTC
9
Screw (for Woofer )
BYC35P120FTC
10
Screw (for Fastener)
BYC35P120FTB
Mark No.
Description
Part No.
S-DV4T
5
56
7
8
56
7
8
C
D
F
A
B
E
2.3 SPEAKER SYSTEM (CENTER)
SPEAKER SYSTEM (CENTER) Parts List
Cabinet
5
8
2
Model Label
10
(x8)
4
9
11
12
Mark No.
Description
Part No.
1
Grille
SMG6129
2
Connecting Cord
SDD1345
3Input Terminal
SKX6034
4
Speaker
K77DR55-52C
5
Screw (for Input Terminal)
BPZ35P080FTC
6
Screw (for Cabinet)
BPZ35P110FTB
7
Non Skid Pad
SEP1263
8
Non Skid Pad
SEP6028