background image


background image
English
2
Thank you for buying this Pioneer product.
Please read through these operating instructions before
using your speaker system so you will know how to make
the most of its performance. After you have finished reading
the instructions, put them away in a safe place for future
reference.
CAUTION
About compatibility
This product is designed exclusively for use with the Pioneer
flat screen TV. For more information on compatibility, please
consult with your nearest Pioneer authorized dealer or
service center.
About installation and setting
· Do not move the flat screen TV by holding the speaker or
speaker brackets. This could result in injury or damage
to the brackets. When moving the TV, hold by the top and
handles.
· The speaker is wide, and may become unstable when
installed by a one person alone. This may result in injury
or product damage. Therefore, at least two people must
assemble and install them.
· When installing the speaker, do not use any screws other
than those supplied, otherwise the speaker may come off
from the main unit and fall over.
· When installing the speaker, tighten the screws firmly.
· Please handle the speaker with sufficient care, as the
grille net and the cabinet can become damaged or broken
when they are subjected to strong external impacts.
· Placing a CRT computer screen or CRT monitor near to
the speaker may result in interference or color distortion.
If this happens, distance the monitor from the speaker.
About the input
· In order to prevent damage to the speaker system
resulting from input overload, please observe the
following precautions:
· Do not connect this speaker to anything other than the
specified flat screen TV. Doing so may result in damage
or fire.
· Be sure to turn the connected devices off and remove
the power cord from the wall outlet beforehand when
changing the connection or installation method.
· When using a tone control function to greatly emphasize
treble sounds, do not use excessive amplifier volume.
CHECKING THE ACCESSORIES
· Speaker Cables × 2
· Speaker Brackets (Left and Right)
· Speaker Bracket (Center)
· Speaker Mounting Screws
(M5 × 10 mm : Black) × 9
· Operating Instructions
Installation
· Consult your dealer if you encounter any difficulties
with this installation.
· Pioneer is not liable for any damage resulting from
improper installation, improper use, modification, or
natural disasters.


background image
3
English
English
· Attach the bracket for center to the lower center on the
rear panel of the flat screen TV using the two supplied
screws.
INSTALLATION ON THE FLAT SCREEN TV
When using the table top stand:
NOTE:
Before attaching the speaker, please attach the PDK-TS35 series table top stand (or another Pioneer flat screen TV stand) to the flat
screen TV.
1. Attach the speaker brackets to the rear of the flat screen TV.
· Attach the brackets for right and left sides to the bottom
right and left on the rear panel of the flat screen TV using
the supplied screws.


background image
English
4
2. Fit the speaker to the brackets in the correct direction.
· Be sure not to mount the speaker upside down.
Caution
· To avoid any damage to the speaker and/or table top stand from striking against each other, fit the speaker to the bracket while
confirming their locations. As you may easily strike the stand, use the protective wrapping in which the speaker was wrapped
between the speaker and stand.
· When the speaker brackets do not fit the grooves at the rear of the speaker, adjust the speaker brackets angle.
3. Tighten from back using the supplied screws (three locations).
· Tighten the three screws in order , , as shown in the diagram.
CAUTION
Do not move the flat screen TV holding on
to the bracket. This can result in injury or
damage to the flat screen TV.
The screw hole at the bottom surface of the
speaker bracket is used when the flat screen
TV is installed on the wall. It is not used when
installed with the stand.
NOTE:
If after attaching the speaker its position needs
to be adjusted horizontally or vertically, first
loosen the speaker mounting screws, reposition
and then tighten the screws again at the
appropriate position.


background image
5
English
English
4. Connect the supplied the speaker
cables to the speaker.
· Connect the cables correctly with respect to the polarity
of the speaker terminals, that is, cable (Gray) to
terminals (Red) and cable (Black) to terminals
(Black).
5. Connect the other end of the speaker
cables to the rear of flat screen TV.
· Connect the cables correctly with respect to the polarity
of the flat screen TV speaker terminals, that is, cable
(Gray) to terminals (Red) and cable (Black) to
terminals (Black).
NOTE:
· Press the lever and insert the end of
the cable.
· When you release the lever, it clamps
onto the speaker cable.
Caution
· Be sure to turn the connected devices off and remove
the power cord from the wall outlet beforehand when
changing the connection or installation method.
· If you insert the speaker cable too far so
that the insulation is touching the speaker
terminal, you may not get any sound. Please
insert it with showing the copper wire.
· Check if the end of the speaker cables are
securely connected to the terminals by
slightly tugging on the cable after making
connections. Loose connections may result
in sound dropouts or noise.
· If there is a short in the and cables caused by an
exposed lead wire, excessive load may be applied to
the flat screen TV, resulting in interrupted operation or
malfunction.
· Incorrect connections of the speaker cable to the right
or left of the flat screen TV terminals with respect to the
polarity may result in insufficient stereo sound effects,
delivering poor bass sounds or unstable sound image.
· Bundle the cable without pulling.