ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2008
PDP-S64
RRV3731
T-ZZR APR. 2008 printerd in Japan
SPEAKER SYSTEM
PDP-S64
SXTW/E5
* Be careful in handling this product, because scratches on cabinet coating are easily
noticeable. When working on this unit, be sure to place the cabinet on a piece of
soft cloth for protection.
SERVICE PRECAUTIONS
2
PDP-S64
1
2
3
4
C
D
F
A
B
E
1
2
3
4
1. REASSEMBLY AND DISASSEMBLY PRECAUTIONS
Network ASSY
When reassembling it,
apply a adhesive to the screws.
1
2
1
Input terminal
1.1 GRILLE ASSY
1
2
3
4
5
6
7
8
11
12
9
10
13
Grille ASSY
Grille ASSY
OK
NG
1.2 WOOFER(Disassembly)
1.3 TWEETER(Disassembly)
Disassembly
Reasassembly
Baffle Assy(Caution)
Network Assy(Caution)
Reasassembly
Reasassembly
The Grille Assy is secured to the baffle plate with two-sided tape
and bosses. When removing the Grille Assy, if is necessary to
wear cotton gloves.
Remove it from the under side.
1. Insert the tip of your gloved finger into the gap between
theGrille Assy in front and the corner of the baffle plate so that the
Grille Assy is slightly lifted.
2. Insert the gloved finger to the extent of the second joint into the
gap between the cabinet and the Grille Assy.
3. Alternately and gradually lift the left and right sides of the
Grille Assy by about 5 cm, sliding gloved fingers along the
cabinet. When lifting the Grille Assy, be sure to lift the left and
right sides alternately, but not both sides simultaneously.
Note: Be careful not to bend the Grille Assy too far. Otherwise, it
may be damaged.
OK : Good example NG : Bad example
Remove the old two-sided tape attached to the rear side of the
Grille Assy and the front side of the Baffle, and adhere new two-
sided
The woofer is secured to the baffle plate with four screws from the
inside. To remove the woofer, first remove the baffle plate.
When reassembling the woofer, place it so that its + terminalis is
facing downward. Tighten the screws to the baffle.
The tweeter is secured to the baffle plate with two screws from the
inside. To remove the tweeter, first remove the baffle plate.
When reassembling the tweeter + terminal fces outside.
When removing the Network Assy, pull it out a little at a time
from alternate sides, because it is seated tightly.
When reassembling the cabinet and the baffle plate, secure the
screws in the order shown in the figure below:
tape. Press the bosses into the baffle plate and press the entire
grille into position.
3
PDP-S64
5
6
7
8
5
6
7
8
C
D
F
A
B
E
2. EXPLODED VIEWS AND PARTS LIST
2.1 PACKING
Tape
Tape
adhesive
Tape
Tape
Refer to "2.2 BRACKET
and BRACKET SETS".
Front
NSP 1
1..Accessory Set
SME3855
2
2..Speaker Wire
SDS1204
3
2..Polyethylene Bag S1
SHL1439
NSP 4
2..Screws Set
SME3852
5
3..Cosmetic Screw M5
SBA1292
6
3..Polyethylene Bag S0
SHL1438
NSP 7
Bracket Set
SME3829
NSP 8
Bracket Set
SME3830
9
Protector
SHA2606
NSP 10
Inner Carton Board
SHB1184
11
Protection Sheet S4
SHC1865
12
Packing Case
SHG2813
NSP 13
1..Inst. Manual Set
SME3846
14
2..Polyethylene bag S2
SHL1437
15
2..Operating Instructions
SRD1360
(English, French, German, Italian,
Dutch, Spanish, Chinese, Russian)
PACKING Parts List
Mark No.
Description
Part No.
Mark No.
Description
Part No.
NSP 16
Label Serial
SRW1112
17
CS Assy L
- - - - - - - -
18
CS Assy R
- - - - - - - -
4
PDP-S64
1
2
3
4
C
D
F
A
B
E
1
2
3
4
1
Polyethylene Bag S0
SHL1372
2
1..Bracket Assy (L-Top)
SXG1166
NSP 3
2..Label (L-Top)
SAK6005
4
2..Gasket
SED1172
5
2..Gasket
SED1189
NSP 6
2..Bracket (L-Top)
SNA1499
7
1..Bracket Assy (R-Bottom)
SXG1169
NSP 8
2..Label (R-Bottom)
SAK6006
9
2..Gasket
SED1172
10
2..Gasket
SED1189
NSP 11
2..Bracket (L-Top)
SNA1499
BRACKET SET Parts List(SME3829)
Mark No.
Description
Part No.
2.2 BRACKET SET
2.2.2 BRACKET SET(SME3830)
2.2.1 BRACKET SET(SME3829)
Tape
Tape
1
Polyethylene Bag S0
SHL1372
2
1..Bracket Assy (R-Top)
SXG1167
NSP 3
2..Label (R-Top)
SAK6007
4
2..Gasket
SED1172
5
2..Gasket
SED1190
NSP 6
2..Bracket Bottom (R-Top)
SNA1500
7
1..Bracket Assy (L-Bottom)
SXG1168
NSP 8
2..Label (L-Bottom)
SAK6004
9
2..Gasket
SED1172
10
2..Gasket
SED1190
NSP 11
2..Bracket Bottom (R-Top)
SNA1500
Mark No.
Description
Part No.
BRACKET SET Parts List(SME3830)
5
PDP-S64
5
6
7
8
5
6
7
8
C
D
F
A
B
E
2.3 CS ASSY
CS ASSY L, R
Lch is symmetrical to center line.
*This product appearance shows Rch.
CABINET(Inside)
BAFFLE(Front)
Grille(Front)
(Rear)
Grille(Back)
Baffle(Back)