ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2007
PDP-S60
RRV3631
SPEAKER SYSTEM
PDP-S60
XTW/E5
* Be careful in handling this product, because scratches on cabinet coating are easily
noticeable. When working on this unit, be sure to place the cabinet on a piece of
soft cloth for protection.
SERVICE PRECAUTIONS
T-ZZR JULY 2007 Printed in Japan
PDP-S60
2
12
3
4
12
3
4
C
D
F
A
B
E
1. REASSEMBLY AND DISASSEMBLY PRECAUTIONS
1.1 GRILLE ASSY
The Grille Assy is secured to the baffle plate with two-sided tape
and bosses. When removing the Grille Assy, if is necessary to wear
cotton gloves.
Disassembly
Remove it from the under side.
1. Insert the tip of your gloved finger into the gap between the
Grille Assy in front and the corner of the baffle plate so that the
Grille Assy is slightly lifted.
2. Insert the gloved finger to the extent of the second joint into the
gap between the cabinet and the Grille Assy.
3. Alternately and gradually lift the left and right sides of the Grille
Assy by about 5 cm, sliding gloved fingers along the cabinet. When
lifting the Grille Assy, be sure to lift the left and right sides alter-
nately, but not both sides simultaneously.
Note: Be careful not to bend the Grille Assy too far. Otherwise, it
may be damaged.
OK : Good example NG : Bad example
Reasassembly
Remove the old two-sided tape attached to the rear side of the Grille
Assy and the front side of the Baffle, and adhere new two-sided
tape. Press the bosses into the baffle plate and press the entire grille
into position. (Press the bosses from the woofer frame.)
1.2 WOOFER (Disassembly)
The woofer is secured to the baffle plate with four screws from the
outside. To remove the woofer, first remove the baffle plate. (Re-
move the baffle plate first, because the cables from the Network
Assy are short.) Remove the two packings from the side of the
woofer frame.
Reasassembly
When reassembling the woofer, place it so that its connector plate
is facing downward. Tighten the screws to the baffle, then attach
the two packings to the side of the woofer frame.
1.3 TWEETER (Disassembly)
The tweeter is secured to the baffle plate with three screws from
the outside. To remove the tweeter, first remove the baffle plate.
(Remove the baffle plate first, because the cables from the Net-
work Assy are short.)
Reasassembly
When reassembling the tweeter, place it so that its connector and
screw-hole positions align with those on the baffle plate.
Network Assy (Caution)
· When removing the Network Assy, pull it out a little at a time
from alternate sides, because it is seated tightly.
Baffle Assy (Caution)
· When reassembling the cabinet and the baffle plate, secure the
screws in the order shown in the figure below:
Grille ASSY
Grille ASSY
OK
NG
Network ASSY
When reassembling it,
apply a adhesive to the screws.
1
2
1
Input terminal
5
6
7
4
3
2
1
PDP-S60
3
5
678
56
7
8
C
D
F
A
B
E
2. EXPLODED VIEWS AND PARTS LIST
2.1 PACKING
PACKING parts List
NOTES :
· Parts marked by " NSP " are generally unavailable because they are not in our Master Spare Parts List.
· The
> mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Tape
Tape
Tape
Refer to "2.2 BRACKET TOP
and BRACKET BOTTOM SETS".
Mark No.
Description
Part No.
NSP 1
1..Accessory Set
SME3782
2
2..Speaker Wire
SDS6049
3
2..Polyethylene Bag S1
SHL1439
NSP 4
2..Screws Set
SME3783
5
3..Screw
BMZ50P100FTB
6
3..Polyethylene Bag S0
SHL1438
NSP 7
Bracket Top Set
SME3785
NSP 8
Bracket Bottom Set
SME3786
9
Protector
SHA2585
10
Protection Sheet S4
SHC6063
11
Packing Case
SHG2784
NSP 12
1..Inst. Manual Set
SME3789
13
2..Polyethylene bag S2
SHL1437
14
2..Operating Instructions
SRD1336
(English, French, German,
Italian, Dutch, Spanish, Chinese)
NSP 15
Label Serial
SRW1112
PDP-S60
4
12
3
4
12
3
4
C
D
F
A
B
E
2.2 BRACKET TOP SET and BRACKET BOTTOM SET
BRACKET TOP SET Parts List
BRACKRT BOTTOM SET Parts List
Tape
Tape
2.2.2 BRACKET BOTTOM SET
2.2.1 BRACKET TOP SET
Mark No.
Description
Part No.
1
Polyethylene Bag S0
SHL6077
2
1..Bracket Assy(L-Top)
SXG1135
NSP 3
2..Label(L-Top)
SAK6005
4
2..Gasket
SED1169
5
2..Gasket
SED1172
NSP 6
2..Bracket Top
SNA1483
7
1..Bracket Assy(R-Top)
SXG1139
NSP 8
2..Label(R-Top)
SAK6007
9
2..Gasket
SED1169
10
2..Gasket
SED1172
NSP 11
2..Bracket Top
SNA1483
1
Polyethylene Bag S0
SHL6077
2
1..Bracket Assy(L-Bottom)
SXG1136
NSP 3
2..Label(L-Bottom)
SAK6004
4
2..Gasket
SED1171
5
2..Gasket
SED1174
NSP 6
2..Bracket Bottom
SNA1484
7
1..Bracket Assy(R-Bottom)
SXG1140
NSP 8
2..Label(R-Bottom)
SAK6006
9
2..Gasket
SED1171
10
2..Gasket
SED1174
NSP 11
2..Bracket Bottom
SNA1484
Mark No.
Description
Part No.
PDP-S60
5
5
678
56
7
8
C
D
F
A
B
E
2.3 SPEAKER SYSTEM (CS ASSY)
Lch is symmetrical to center line.
*This product appearance shows Rch.
x14
x13
25
35
35