PDP-S51
Operating Instructions
Mode d'emploi
Speaker System
Enceintes acoustiques
English
2
Thank you for buying this Pioneer product.
Please read through these operating instructions before
using your speaker system so you will know how to make
the most of its performance. After you have finished
reading the instructions, put them away in a safe place for
future reference.
WARNING: Handling the power cord on this product or
cords associated with accessories sold with the product
will expose you to lead, a chemical known to the State
of California and other governmental entities to cause
cancer and birth defects or other reproductive harm.
Wash hands after handling.
CAUTION
About compatibility
This product is designed exclusively for use with the
Pioneer Plasma Display. For more information on
compatibility, please consult with your nearest Pioneer
authorized dealer or service center.
About installation and setting
÷ Attach the Plasma Display to the stand before installing
the speakers. See the Operating Instructions packed
together with the stand for how to assemble the stand.
÷ Do not lift up the display by the speakers. A speaker
may come off, so carry the display by holding it by the
top and its handle.
÷ When installing the speaker, do not use any screws
other than those supplied, otherwise the speaker may
come off from the main unit and fall over.
÷ When installing the speaker, tighten the screws firmly.
÷ Please handle the speaker with sufficient care, as the
grille net and the cabinet can become damaged or
broken when they are subjected to strong external
impacts.
÷ Placing a CRT computer screen or CRT monitor near to
the speaker may result in interference or color
distortion. If this happens, distance the monitor from
the speaker.
About the input
÷ In order to prevent damage to the speaker system
resulting from input overload, please observe the
following precautions:
÷ Do not use the speaker with anything other than the
specified Pioneer Plasma Display. Doing so may result
in damage or fire.
÷ Be sure to turn the connected devices off and remove
the power cord from the wall outlet beforehand when
changing the connection or installation method.
÷ When using a tone control function to greatly
emphasize treble sounds, do not use excessive
amplifier volume.
Installation
÷ Consult your dealer if you encounter any difficulties
with this installation.
÷ Pioneer is not liable for any damage resulting from
improper installation, improper use, modification, or
natural disasters.
CHECKING THE ACCESSORIES
7 Speaker Cable × 2
7 Speakers Mounting Screw (M4 × 10 mm: Black) × 8
7 Speakers Mounting Screw (M5 × 10 mm: Black) × 8
7 Speaker Mounting Bracket
7 Cushions × 2
7 Operating Instructions × 1
For LEFT-TOP
For LEFT-BOTTOM
For RIGHT-BOTTOM
For RIGHT-TOP
3
English
English
MOUNTING THE SPEAKERS
TO YOUR PLASMA DISPLAY
NOTE:
The diagram depicts the mounting of the right
speaker. The left speaker mounts in the same way.
1. 1 Attach the speakers to the speakers mounting
bracket (top and bottom) with the speakers
mounting screws (M4
× 10 mm).
2 Remove the seals from the cushions and then
attach the cushions to the sides of the speakers
in the locations indicated in the diagram below.
Speakers Mounting
Screw (M4
× 10 mm)
Speakers Mounting
Screw (M4
× 10 mm)
Speaker Mounting
Bracket (For
RIGHT-TOP)
Speaker Mounting
Bracket (For RIGHT-
BOTTOM)
Tighten the bottom speaker
mounting bracket to the display
temporarily (one place bottom).
After passing the wide part of the
hole over the screw, lower the
speaker.
3. Hang the speaker mounting bracket on the screw
you installed at the top by passing the wide part
over it and lowering into the slot; screw in the
lower screw temporarily.
After passing the wide part of the hole of the speaker
mounting bracket (top) over the screw, lower the
speaker onto it.
2. Loosely attach the speakers mounting screws
(M5
× 10 mm) to the plasma display (one location
on the left and one on the right).
Do not tighten it all the way yet. Leave it loose, with
about 5 mm left to tighten.
4. Adjust the position of the speaker and then fix the
upper and lower screws firmly.
· Adjust the positions of the speakers and the Plasma
Display so their top surfaces are the same height.
· Adjust the positions of the speakers and the Plasma
Display so their side surfaces are parallel.
5. Ti ghten the two screws, at the top and bottom for
each speaker (total of four screws), thus fixing the
speakers to the display.
Top, Back of
Display
5 mm
Leave a space of about 5 mm
Speakers Mounting Screw
(M5
× 10 mm)
Speakers Mounting Screw
(M5
× 10 mm)
Speakers Mounting Screw
(M5
× 10 mm)
Speakers Mounting Screw
(M5
× 10 mm)
Speaker R
Speaker L
Cushion
Cushion
English
4
Connecting your Speaker Cables (to the
display)
Connect the cables correctly with respect to the
polarity of the Plasma Display and the speaker
terminals, that is,
ª cable to ª terminals and ·
cable to
· terminals. To do so, connect the cable
with the gray line to the
ª terminals and the white
cable to the
· terminals.
Push the lever, insert the end of the speaker cable
into the hole, and release the lever.
Pay attention to the polarity of the speaker
terminals when making connections. (The gray line
represents the red terminal)
NOTE:
·
Press the lever and insert the end of
the cable.
·
When you release the lever, it clamps
onto the speaker cable.
Caution
·
Be sure to turn the connected devices off and remove
the power cord from the wall outlet beforehand when
changing the connection or installation method.
·
If you insert the speaker cable too far so
that the insulation is touching the
speaker terminal, you may not get any
sound. Please insert it with showing the
copper wire.
Gray line
Gray line
White
Red
Black
Red
Red
White
Gray line
Connecting your Speaker Cables
(to the speaker)
CONNECTION TO A PLASMA DISPLAY
·
Check if the end of the speaker cables are securely
connected to the terminals by slightly tugging on the
cable after making connections. Loose connections
may result in sound dropouts or noise.
·
If there is a short in the
and
cables caused by an
exposed lead wire, excessive load may be applied to
the Plasma Display, resulting in interrupted operation or
malfunction.
·
Incorrect connections of the speaker cable to the right
or left of the Plasma Display terminals with respect to
the polarity may result in insufficient stereo sound
effects, delivering poor bass sounds or unstable sound
image.
·
Bundle the code without pulling the cord.
Black
5
English
English
CABINET MAINTENANCE
÷ Use a polishing cloth or dry cloth to wipe off dust and
dirt.
÷ When the cabinet is very dirty, wipe with a soft cloth
moistened with water-diluted cleanser; then wipe again
with a dry cloth. Do not use furniture wax or cleaners.
They may damage the surface of the cabinet.
÷ Never use thinner, benzine, insecticide sprays and
other chemicals on or near the cabinets, since these
will corrode the surfaces.
÷ When a chemical cloth is used, read the cautions for
the chemical cloth carefully.
SPECIFICATIONS
Cabinet: Bass-reflex type
Used speakers (two-way system):
Woofer (for low tones) ........................... 7 cm cone type
Tweeter (for high tones) ........................ 5 cm cone type
Nominal impedance ..................................................... 8
Frequency Range ..................................... 65 Hz to 35 kHz
Sensitivity (1 w, 1 m) ................................................ 85 dB
Permissible input :
Max. input .............................................................. 13 W
Rated input ............................................................... 4 W
Crossover frequency ................................................ 4 kHz
External Dimensions
.......................... 90 mm (W)
× 880 mm (H) × 92 mm (D)
Weight ..................................................................... 2.4 kg
Accessory parts (for 2 speakers)
............................................................ Speaker cable
× 2
................................................ Screw (M4
× 10 mm) × 8
................................................ Screw (M5
× 10 mm) × 8
............................................................................. Bracket
LEFT-TOP
× 1
LEFT-BOTTOM
× 1
RIGHT-TOP
× 1
RIGHT-BOTTOM
× 1
.................................................................... Cushions
× 2
.............................................. Operating Instructions
× 1
NOTE:
Specifications and design subject to possible modification
without notice, due to improvements.
Published by Pioneer Corporation.
Copyright © 2006 Pioneer Corporation.
All rights reserved.
IMPORTANT NOTICE RECORD THE MODEL NUMBER AND SERIAL NUMBERS OF THIS EQUIPMENT BELOW.
THE NUMBERS ARE ON THE REAR.
MODEL NO.
SERIAL NO.
KEEP THESE NUMBERS FOR FUTURE USE.
D1-4-2-6-2_En
HOW TO ROURE CABLES
Speed clamps are included with the Plasma Display for
tidying your cables and keeping extra cable length out of
the way.
Attach speed clamps at the direction of the running cables.
*
When the Pioneer stand, sold separately, is not used, use the 4
holes that are marked with arrows in the diagram (
) as the
holes for attaching speed clamps.
Using Speed Clamps
Wrap the speed clamp around the bundled
cables and press B into hole A.
To remove a speed clamp, use pliers to
twist it 90° and then pull it out. (This may
result in weakening or damaging the
clamp.)
If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used
electronic products in accordance with legislation that requires proper treatment, recovery and recycling.
Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to
designated collection facilities or to a retailer (if you purchase a similar new one).
For countries not mentioned above, please contact your local authorities for the correct method of disposal.
By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential
negative effects on the environment and human health.
K058_En
Rear of Display
Speaker Cable
Speed Clamp
Mounting Hole
Speed Clamp
Speed Clamp
Mounting Hole