PDP-S34-LR
PDP-S33-LR
Operating Instructions
Mode d'emploi
Manual de instrucciones
Speaker System
Enceintes acoustiques
Sistema de altavoces
SRD1281A_En_01_07
05.2.28, 2:49 PM
1
English
2
CHECKING THE ACCESSORIES
7 Speaker cable x 2
Thank you for buying this Pioneer product.
Please read through these operating instructions before
using your speaker system so you will know how to make
the most of its performance. After you have finished reading
the instructions, put them away in a safe place for future
reference.
BEFORE USE
÷ The nominal impedance of this speaker system is 8 ohms.
÷ In order to prevent damage to the speaker system
resulting from input overload, please observe the
following precautions:
÷ Do not supply power to the speaker system in
excess of the maximum permissable input. This
can result in damage or a possible fire hazard.
÷ When connecting or disconnecting pin-plugs, be
sure that amplifier power is OFF.
÷ When using a graphic equalizer to emphasize loud
sounds of a high frequency range, do not use
excessive amplifier volume.
÷ Do not force a low-powered amplifier to produce a
loud volume of sound (the amplifier's harmonic
distortion will be increased, and you may damage
the speaker).
÷ Please handle the speakers with sufficient care, as
the grille net and the cabinet can become damaged
or broken when they are subjected to strong external
impacts.
÷ Placing a CRT computer screen or CRT monitor near to
the speakers may result in interference or color distortion.
If this happens, distance the monitor from the speakers.
7 Operating Instructions
7 Speaker mounting fittings (Used when installing the
speakers flush with the display)
Bracket for flush mounting (RIGHT) x 2
7 Speaker mounting fittings (Used when installing the
speakers set back with the display)
7 Speakers mounting screws
(M5 x 10mm : Black) x 12
NOTE:
÷ Always use the accessory mounting fittings for
installation.
÷ When screws other than those enclosed as accessories
are used to install the speakers, the speakers may drop
off or accidents may be caused. Always use the screws
enclosed as accessories.
Installation
÷ Consult your dealer if you encounter any difficulties
with this installation.
÷ Pioneer is not liable for any damage resulting from
improper installation, improper use, modification, or
natural disasters.
Bracket for set back mounting (RIGHT) x 2
WARNING:
Handling the power cord on this product or cords
associated with accessories sold with the product will
expose you to lead, a chemical known to the State of
California and other governmental entities to cause cancer
and birth defects or other reproductive harm.
Wash hands after handling.
Bracket for flush mounting (LEFT) x 2
CAUTION:
÷ Attach the Plasma Display to the stand before installing
the speakers. See the Operating Instructions packed to-
gether with the stand for how to assemble the stand.
÷ Do not place force on the speakers' front panel grille net,
or stick your finger or other object into the front of the
speaker, since you may damage the grille net or speaker
unit itself.
Bracket for set back mounting (LEFT) x 2
The customer can select whether to install the speakers flush
with the screen or set back slightly.
Flush
Set back
See the description below for details of the installation.
NOTE:
÷ If you install the speakers flush, you cannot use the
buttons on the right side of the display. Please use the
remote control.
SRD1281A_En_01_07
05.2.28, 2:49 PM
2
3
English
English
INSTALLATION ON THE PLASMA
DISPLAY
Flush mount
Perform installation according to the following steps 1 to 2.
1 Attach the mounting fittings to the
speakers.
The illustration below shows the right speaker. Attach the left
side mounting fitting in the same way.
1 Attach a bracket for flush mounting (RIGHT) to the top of
the right speaker, as shown.
2 Attach another bracket for flush mounting (RIGHT) to the
bottom of the speaker in the same way.
2 Attach the speakers to the display.
The illustration below shows how to attach of the right speaker.
Attach the left speaker in the same way.
1 Fix the upper screw temporarily in
advance to hang the speaker on the
display (In this case, leave a space
of about 5 mm between the head
of the screw and the display).
2 Hang the speaker on the upper screw.
3 Fix the lower screw temporarily.
4 Adjust the position of the speaker and then fix the upper
and lower screws firmly.
5 mm
The display
2
1
2
4
3
Padding
strip
Set back mount
Perform installation according to the following steps 1 to 2.
1 Attach the mounting fittings to the
speakers.
The illustration below shows the right speaker. Attach the left
side mounting fitting in the same way.
1 Attach a bracket for set back mounting (RIGHT) to the
top of the right speaker, as shown.
2 Attach another bracket for set back mounting (RIGHT) to
the bottom of the speaker in the same way.
2 Attach the speakers to the display.
The illustration below shows how to attach
of the right speaker. Attach the left speaker
in the same way.
1 Fix the upper screw temporarily in
advance to hang the speaker on the
display (In this case, leave a space
of about 5 mm between the head of
the screw and the display).
2 Hang the speaker on the upper screw.
3 Fix the lower screw temporarily.
4 Adjust the position of the speaker and then fix the upper
and lower screws firmly.
2
1
Padding
strip
5 mm
The display
2
4
3
SRD1281A_En_01_07
05.2.28, 2:49 PM
3
English
4
CONNECTION TO A PLASMA
DISPLAY
1 Connecting the speaker cables
Before connecting the speaker cables, unplug the Plasma
Display from the power outlet. After you have finished
connecting up, plug the unit back into the power outlet.
Connect the input terminals of the speaker system and
the speaker output terminals of the Plasma Display with
the accessory speaker cables. Make sure the positive (
ª)
and negative (
·) terminals match when connecting.
1. Push the lever, insert the cable into the hole, and release
the lever.
2. For the output terminals on the Plasma Display, push the
lever, insert the cable into the hole, and release the lever.
To the
· terminal
To the
ª terminal
(Speaker input terminals of the speaker system)
· terminal (black) ª terminal (red)
Input terminal of speaker
White
White with gray line
ª ··ª
RL
Output terminal of Plasma
Display
÷ After connection to the terminals, pull lightly on the cable
to confirm that the tips of the cable are properly con-
nected to the terminals. An imperfect connection can
cause sound interruptions and noise.
÷ When cable cores stick out and ª and · lines are short-
circuited, an excessive load will be applied to the Plasma
Display and the operation will stop or trouble will be
caused.
÷ When the polarity is reversed for one speaker (left or right)
at the time of connection to the Plasma Display, the bass
reproduction will be reduced, the sound positioning will
be lost, and a correct stereo effect will not be obtained.
÷ If you insert the speaker cable too far so that the insula-
tion is touching the speaker terminal, you may not get
any sound.
When the display is to be moved after speaker
installation, do not hold the display by the speakers.
Do not hold the speakers and raise the display. This
may cause the deformation or damage of products.
< right >
< wrong >
CAUTION
SRD1281A_En_01_07
05.2.28, 2:50 PM
4
5
English
English
2 How to route cables
Speed clamps and bead bands are supplied for bunching cables. Once properly bunched, follow the steps below to route the
cables.
When the speakers are installed on the sides
The below rear view shows
flush mounting, however cable routing for set back mounting will be the same.
Speaker cable
Speaker cable
Speed clamps
Bead band
Attaching speed clamps to the main unit
Attach the speed clamps using any of the 5 holes you prefer
marked with
below, depending on your routing system.
Attaching and removing speed clamps
Insert 1 into an appropriate hole on the rear of the Plasma
Display and snap 2 into the back of 1 to lock the clamp.
Speed clamps are designed to be difficult to undo once in
place. Please attach them carefully.
To remove, use pliers to twist the clamp 90°, pulling
outward. The clamp may deteriorate over time and become
damaged if removed.
1
2
Bunching and securing cables with the
bead bands.
Do not allow excessive stress to be placed on the ends of
cables.
SRD1281A_En_01_07
05.2.28, 2:50 PM
5