PDP-S31-LR
PDP-S30-LR
Operating Instructions
Mode d'emploi
Manual de instrucciones
Speaker System
Enceintes acoustiques
Sistema de altavoces
SRD1281A_En_01_07
04.10.14, 3:06 PM
1
English
2
CHECKING THE ACCESSORIES
7 Speaker cable x 2
Thank you for buying this Pioneer product.
Please read through these operating instructions before
using your speaker system so you will know how to make
the most of its performance. After you have finished reading
the instructions, put them away in a safe place for future
reference.
BEFORE USE
÷ The nominal impedance of this speaker system is 8 ohms.
÷ In order to prevent damage to the speaker system
resulting from input overload, please observe the
following precautions:
÷ Do not supply power to the speaker system in
excess of the maximum permissable input. This
can result in damage or a possible fire hazard.
÷ When connecting or disconnecting pin-plugs, be
sure that amplifier power is OFF.
÷ When using a graphic equalizer to emphasize loud
sounds of a high frequency range, do not use
excessive amplifier volume.
÷ Do not force a low-powered amplifier to produce a
loud volume of sound (the amplifier's harmonic
distortion will be increased, and you may damage
the speaker).
÷ Please handle the speakers with sufficient care, as
the grille net and the cabinet can become damaged
or broken when they are subjected to strong external
impacts.
÷ Placing a CRT computer screen or CRT monitor near to
the speakers may result in interference or color distortion.
If this happens, distance the monitor from the speakers.
7 Operating Instructions
7 Speaker mounting fittings (Used when installing the
speakers flush with the display)
Bracket for flush mounting (RIGHT) x 2
7 Speaker mounting fittings (Used when installing the
speakers set back with the display)
7 Speakers mounting screws
NOTE:
÷ Always use the accessory mounting fittings for
installation.
÷ When screws other than those enclosed as accessories
are used to install the speakers, the speakers may drop
off or accidents may be caused. Always use the screws
enclosed as accessories.
Notes on Installation Work:
This product is marketed assuming that it is installed by
qualified personnel with enough skill and competence.
Always have an installation specialist or your dealer install
and set up the product.
PIONEER cannot assume liabilities for damage caused
by mistake in installation or mounting, misuse,
modification or a natural disaster.
x 12
Bracket for set back mounting (RIGHT) x 2
WARNING:
Handling the power cord on this product or cords
associated with accessories sold with the product will
expoes you to lesd, a chemical known to the State of
California and other governmental entities to cause cancer
and birth defects or other reproductive harm.
Wash hands after handling.
Bracket for flush mounting (LEFT) x 2
CAUTION:
÷ Attach the plasma display to the stand before installing
the speakers. See the Operating Instructions packed to-
gether with the stand for how to assemble the stand.
÷ Do not place force on the speakers' front panel grille net,
or stick your finger or other object into the front of the
speaker, since you may damage the grille net or speaker
unit itself.
Bracket for set back mounting (LEFT) x 2
The customer can select whether to install the speakers flush
with the screen or set back slightly.
Flush
Set back
See the description below for details of the installation.
NOTE:
÷ If you install the speakers flush, you cannot use the
buttons on the right side of the display. Please use the
remote control.
SRD1281A_En_01_07
04.10.14, 3:06 PM
2
3
English
English
INSTALLATION ON THE PLASMA
DISPLAY
Flush mount
Perform installation according to the following steps 1 to 2.
1 Attach the mounting fittings to the
speakers.
The illustration below shows the right speaker. Attach the left
side mounting fitting in the same way.
1 Attach a bracket (RIGHT) to the top of the right speaker,
as shown.
2 Attach another bracket (RIGHT) to the bottom of the
speaker in the same way.
2 Attach the speakers to the display.
The illustration below shows how to attach of the right speaker.
Attach the left speaker in the same way.
1 Fix the upper screw temporarily in
advance to hang the speaker on the
display (In this case, leave a space
of about 5 mm between the head
of the screw and the display).
2 Hang the speaker on the upper screw.
3 Fix the lower screw temporarily.
4 Adjust the position of the speaker and then fix the upper
and lower screws firmly.
5 mm
The display
2
1
2
4
3
Padding
strip
Set back mount
Perform installation according to the following steps 1 to 2.
1 Attach the mounting fittings to the
speakers.
The illustration below shows the right speaker. Attach the left
side mounting fitting in the same way.
1 Attach a bracket (RIGHT) to the top of the right speaker,
as shown.
2 Attach another bracket (RIGHT) to the bottom of the
speaker in the same way.
2 Attach the speakers to the display.
The illustration below shows how to attach of the right speaker.
Attach the left speaker in the same way.
1 Fix the upper screw temporarily in
advance to hang the speaker on the
display (In this case, leave a space
of about 5 mm between the head of
the screw and the display).
2 Hang the speaker on the upper screw.
3 Fix the lower screw temporarily.
4 Adjust the position of the speaker and then fix the upper
and lower screws firmly.
2
1
Padding
strip
5 mm
The display
2
4
3
SRD1281A_En_01_07
04.10.14, 3:06 PM
3
English
4
CONNECTION TO A PLASMA
DISPLAY
1 Connecting the speaker cables
Before connecting the speaker cords, unplug the plasma
display from the power outlet. After you have finished
connecting up, plug the unit back into the power outlet.
Connect the input terminals of the speaker system and
the speaker output terminals of the plasma display with
the accessory speaker cable. Make sure the positive (
ª)
and negative (
·) terminals match when connecting.
1. Push the lever, insert the cable into the hole, and release
the lever.
2. For the output terminals on the plasma display, push the
lever, insert the cable into the hole, and release the lever.
To the
· terminal
To the
ª terminal
(Speaker input terminals of the speaker system)
· terminal (black) ª terminal (red)
Input terminal of speaker
White
White with gray line
ª ··ª
RL
Output terminal of plasma
display
÷ After connection to the terminals, pull lightly on the cable
to confirm that the tips of the cable are properly con-
nected to the terminals. An imperfect connection can
cause sound interruptions and noise.
÷ When cable cores stick out and ª and · lines are short-
circuited, an excessive load will be applied to the plasma
display and the operation will stop or trouble will be
caused.
÷ When the polarity is reversed for one speaker (left or right)
at the time of connection to the plasma display, the bass
reproduction will be reduced, the sound positioning will
be lost, and a correct stereo effect will not be obtained.
÷ If you insert the speaker cord too far so that the insulation
is touching the speaker terminal, you may not get any
sound.
NOTE:
÷ When the display is to be moved after speaker installa-
tion, do not hold the display by the speakers. Hold the
display with one hand on the bottom of the unit and the
other on the handle on the rear. Do not hold the speakers
and raise the display. This may cause the deformation
or damage of products.
< right >
< wrong >
SRD1281A_En_01_07
04.10.14, 3:06 PM
4
5
English
English
2 How to route cables
Speed clamps are included with the plasma display for tidying your cables and keeping extra cable length out of the way.
Flush mount
Use the supplied wiring clamp to hide the cables from view.
Set back mount
Speed clamps
Speaker cable
Speaker cable
Wiring clamp
Speed clamps
Speaker cable
Speaker cable
Wiring clamp
Speed clamps
Speed clamps
SRD1281A_En_01_07
04.10.14, 3:06 PM
5