PIONEER PDP-S26-LR/XIN1/E - Owner's Manual Immediate Download

PDP-S25-LR

PDP-S26-LR

Operating Instructions

Mode d'emploi

Bedienungsanleitung

Istruzioni per l'uso

Gebruiksaanwijzing

Manual de instrucciones

Speaker System

Enceintes acoustiques

Lautsprechersystem

Sistema di diffusori

Luidsprekersysteem

Sistema de altavoces

English

See the description below for details of the installation.

NOTE:

÷ If you install the speakers flush/air, you cannot use the

buttons on the right side of the display. Please use the

remote control.

CHECKING THE ACCESSORIES

7 Speaker cable x 2

Thank you for buying this Pioneer product.

Please read through these operating instructions before

using your speaker system so you will know how to make

the most of its performance. After you have finished reading

the instructions, put them away in a safe place for future

reference.

BEFORE USE

÷ The nominal impedance of this speaker system is 8 ohms.

÷ In order to prevent damage to the speaker system

resulting from input overload, please observe the

following precautions:

÷ Do not supply power to the speaker system in

excess of the maximum permissable input. This

can result in damage or a possible fire hazard.

÷ When connecting or disconnecting pin-plugs, be

sure that amplifier power is OFF.

÷ When using a graphic equalizer to emphasize loud

sounds of a high frequency range, do not use

excessive amplifier volume.

÷ Do not force a low-powered amplifier to produce a

loud volume of sound (the amplifier's harmonic

distortion will be increased, and you may damage

the speaker).

÷ Please handle the speakers with sufficient care, as

the grille net and the cabinet can become damaged

or broken when they are subjected to strong external

impacts.

÷ Placing a CRT computer screen or CRT monitor near to

the speakers may result in interference or color distortion.

If this happens, distance the monitor from the speakers.

7 Operating Instructions

7 Speaker mounting fittings (Used when installing the

speakers flush with the display)

Bracket for flush mounting (RIGHT) x 2

7 Speaker mounting fittings (used when mounting

the speaker so as to allow angle adjustment)

7 Speakers mounting screws

NOTE:

÷ Always use the accessory mounting fittings for

installation.

÷ When screws other than those enclosed as accessories

are used to install the speakers, the speakers may drop

off or accidents may be caused. Always use the screws

enclosed as accessories.

Notes on Installation Work:

This product is marketed assuming that it is installed by

qualified personnel with enough skill and competence.

Always have an installation specialist or your dealer install

and set up the product.

PIONEER cannot assume liabilities for damage caused

by mistake in installation or mounting, misuse,

modification or a natural disaster.

x 12

Speakers are designed to allow the two methods of

installation shown, in accordance with the user's preference:

1. Flush: Speakers are mounted flat against the sides of

the display, and fixed in position (non-adjustable).

2. Air: Speakers are mounted apart from the sides of the

display, so as to allow adjustment of their angles.

Flush

Air

Bracket for air

mounting (R) x 1

WARNING:

Handling the power cord on this product or cords

associated with accessories sold with the product will

expoes you to lesd, a chemical known to the State of

California and other governmental entities to cause cancer

and birth defects or other reproductive harm.

Wash hands after handling.

Bracket for flush mounting (LEFT) x 2

Bracket for air

mounting (L) x 1

Padding strip x 2

Covers (upper) x 2

Covers (lower) x 2

English

INSTALLATION ON THE PLASMA

DISPLAY

Flush mount (for fixed-angle installation)

Perform installation according to the following steps 1 to 2.

1 Attach the mounting fittings to the

speakers.

The illustration below shows the right speaker. Attach the left

side mounting fitting in the same way.

1 Attach a bracket (RIGHT) to the top of the right speaker,

as shown.

2 Attach another bracket (RIGHT) to the bottom of the

speaker in the same way.

2 Attach the speakers to the display.

The illustration below shows how to attach of the right speaker.

Attach the left speaker in the same way.

1 Fix the upper screw temporarily in

advance to hang the speaker on the

display (In this case, leave a space

of about 5 mm between the head

of the screw and the display).

5 mm

The display

INSTALLATION ON THE PLASMA

DISPLAY

Air mount (for adjustable-angle installation)

Perform installation according to the following steps 1 to 2.

1 Attach the mounting fittings to the

speakers.

The illustration below shows the right speaker. Attach the left

side mounting fitting in the same way.

1 Attach the speaker bracket (R) to the right-side speaker.

Remove the locking screw as shown.

2 Attach the top and bottom covers.

The right and left lower speaker

brackets are pre-applied with two-

sided tape to prevent the lower covers

from dropping.

Remove

the

protective paper

from the tape

before fixing the

covers in place.

Locking screw

2 Hang the speaker on the upper screw.

3 Fix the lower screw temporarily.

4 Adjust the position of the speaker and then fix the upper

and lower screws firmly.

CAUTION:

÷ Attach the plasma display to the stand before installing

the speakers. See the Operating Instructions packed to-

gether with the stand for how to assemble the stand.

÷ Do not place force on the speakers' front panel grille net,

or stick your finger or other object into the front of the

speaker, since you may damage the grille net or speaker

unit itself.

÷ When using the "Air" method of

mounting speakers: if the speaker angle

is changed, be sure to lock the speaker

before use, to prevent it from moving.

If the speaker is left in the movable

position, personal injury could results by

pinching fingers in the gap between

speaker and display.

Padding

strip

* Apply the padding strip to

the side of the speaker.

The locking screw is located in the

bottom side of the speaker only.

Protective

paper

English

CONNECTION TO A PLASMA

DISPLAY

1 Connecting the speaker cables

1 Switch off the power of the plasma display.

2 Connect the input terminals of the speaker system and

the speaker output terminals of the plasma display with

the accessory speaker cable. Make sure the positive (

ª)

and negative (

·) terminals match when connecting.

1. Push the lever, insert the cable into the hole, and release

the lever.

2. For the output terminals on the plasma display, push the

lever, insert the cable into the hole, and release the lever.

To the

· terminal

To the

ª terminal

(Speaker input terminals of the speaker system)

· terminal (black) ª terminal (red)

Input terminal of speaker

White

White with gray line

ª ··ª

Output terminal of plasma

display

÷ After connection to the terminals, pull lightly on the cable

to confirm that the tips of the cable are properly con-

nected to the terminals. An imperfect connection can

cause sound interruptions and noise.

÷ When cable cores stick out and ª and · lines are short-

circuited, an excessive load will be applied to the plasma

display and the operation will stop or trouble will be

caused.

÷ When the polarity is reversed for one speaker (left or right)

at the time of connection to the plasma display, the bass

reproduction will be reduced, the sound positioning will

be lost, and a correct stereo effect will not be obtained.

2 Attach the speakers to the display.

Theillustrationbelowshows how toattach

ofthe rightspeaker. Attach the left speaker

in the same way.

1 Fix the upper screw temporarily in

advance to hang the speaker on the

display (In this case, leave a space

of about 5 mm between the head

of the screw and the display).

2 Hang the speaker on the upper screw.

3 Fix the lower screw temporarily.

4 Adjust the position of the speaker and then fix the upper

and lower screws firmly.

5 Secure the cable with the cable clip as shown, then press

the remaining speaker cable into the groove (in the lower

cover).

ì Changing the Speaker Angle

1 Remove the upper cover.

2 After pulling up the locking lever, change

the speaker angle as desired, then push

the locking lever down again.

NOTE:

÷ When the display is to be

moved after speaker installa-

tion, do not hold the display by

the speakers. Hold the display

with one hand on the bottom

of the unit and the other on the

handle on the rear. Do not hold

the speakers and raise the

display. This may cause the

deformation or damage of

products.

5 mm

The display

The speakers can be

adjusted in one of

four angle positions

as desired.

English

2 How to route cables

Speed clamps are included with the plasma display for

tidying your cables and keeping extra cable length out of the

way.

Flush mount (for fixed-angle installation)

Use the supplied wiring clamp to hide the cables from view.

÷ If you insert the speaker cord too far so that the insulation

is touching the speaker terminal, you may not get any

sound.

< right >

< wrong >

Air mount (for adjustable-angle installation)

Speed clamps

Speaker cable

Wiring clamp

Speaker cable

Wiring clamp

Cover

Cable clip