PIONEER PDP-S22-LR/XIN1/E - Owner's Manual Immediate Download

PDP-S21-LR

PDP-S22-LR

Operating Instructions

Mode d'emploi

Bedienungsanleitung

Istruzioni per l'uso

Gebruiksaanwijzing

Manual de instrucciones

Speaker System

Enceintes acoustiques

Lautsprechersystem

Sistema di diffusori

Luidsprekersysteem

Sistema de altavoces

English

CHECKING THE ACCESSORIES

7 Speaker cable x 2

Thank you for buying this Pioneer product.

Please read through these operating instructions before

using your speaker system so you will know how to make

the most of its performance. After you have finished reading

the instructions, put them away in a safe place for future

reference.

WARNING:

Handling the power cord on this product or cords

associated with accessories sold with the product will

expoes you to lesd, a chemical known to the State of

California and other governmental entities to cause cancer

and birth defects or other reproductive harm.

Wash hands after handling.

BEFORE USE

÷ The nominal impedance of this speaker system is 8 ohms.

÷ In order to prevent damage to the speaker system

resulting from input overload, please observe the

following precautions:

÷ Do not supply power to the speaker system in

excess of the maximum permissable input. This

can result in damage or a possible fire hazard.

÷ When connecting or disconnecting pin-plugs, be

sure that amplifier power is OFF.

÷ When using a graphic equalizer to emphasize loud

sounds of a high frequency range, do not use

excessive amplifier volume.

÷ Do not force a low-powered amplifier to produce a

loud volume of sound (the amplifier's harmonic

distortion will be increased, and you may damage

the speaker).

÷ An automatic restore-type protective device is incorporated

to protect the speakers from excessive input signals or

abnormal signals. When an excessive input signal is sent

to the speakers, the protective device is activated and

loud high-pitched sounds will be prevented. In this case,

lower the volume of the plasma display during use. After

5 to 10 seconds, the speakers are restored automatically.

÷ Placing a CRT computer screen or CRT monitor near to

the speakers may result in interference or color distortion.

If this happens, distance the monitor from the speakers.

7 Operating Instructions

7 Speaker mounting fittings (Used when installing the

speakers on the right and left sides of the display)

Bracket for installing the

speakers on the right x 2

7 Speaker mounting fittings (Used when installing the

speakers at the bottom of the display)

7 Speakers mounting screws

NOTE:

÷ Always use the accessory mounting fittings for

installation.

÷ When screws other than those enclosed as accessories

are used to install the speakers, the speakers may drop

off or accidents may be caused. Always use the screws

enclosed as accessories.

Notes on Installation Work:

This product is marketed assuming that it is installed by

qualified personnel with enough skill and competence.

Always have an installation specialist or your dealer install

and set up the product.

PIONEER cannot assume liabilities for damage caused

by mistake in installation or mounting, misuse,

modification or a natural disaster.

x 12

The customer can select whether to install the speakers on

the right and left sides of the display or at the bottom of the

display.

When the speakers are installed

on the right and left sides

When the speakers are

installed at the bottom

See the description below for details of the installation.

CAUTION:

÷ Attach the plasma display to the stand (PDK-TS05) before

installing the speakers. See the Operating Instructions

packed together with the stand for how to assemble the

stand.

Bracket for installing the speakers at

the bottom x 2 for right and left sides

Bracket for installing the speakers

at the bottom x 1 for center

Rivet for installing the speakers at

the bottom x 2

Bracket for installing the

speakers on the left x 2

English

INSTALLATION ON THE PLASMA

DISPLAY

(WHEN INSTALLING THE SPEAKERS ON THE RIGHT AND

LEFT SIDES OF THE DISPLAY)

1 Attach the mounting fittings to the

speakers.

The illustration below shows the right speaker. Attach the left

side mounting fitting in the same way.

1 Attach a bracket (R) to the top of the right speaker, as

shown.

2 Attach another bracket (R) to the bottom of the speaker

in the same way.

2 Attach the speakers to the display.

The illustration below shows how to attach of the right speaker.

Attach the left speaker in the same way.

1 Fix the upper screw temporarily in

advance to hang the speaker on

the display (In this case, leave a

space of about 5 mm between the

head of the screw and the display).

2 Hang the speaker on the upper

screw.

3 Fix the lower screw temporarily.

4 Adjust the position so that the speaker is parallel to the

display and then fix the upper and lower screws firmly.

Perform installation according to the following steps 1 to 2.

INSTALLATION ON THE PLASMA

DISPLAY

(WHEN INSTALLING THE SPEAKERS AT THE BOTTOM

OF THE DISPLAY)

1 Attach the mounting fittings to the

display.

1 Push rivets into each (lower) outside hole of brackets (on

the right and left sides).

2 Lightly finger-tighten a screw into the (upper) outside hole of

each bracket.

3 Insert the screws into the two outside holes of bracket

(at the center), and tighten them.

4 Attach the speaker cushions supplied with your plasma

display.

5 Align the bosses of the spacer with the holes of the stand

and insert them.

5mm

The display

Perform installation according to the following steps 1 to 2.

Separate the 3 cushions evenly, making

sure you don't cover the screws with the

speaker cushions when placing them.

Lower back side of the plasma

display speaker system

English

2 Similarly, insert the other speaker into the bracket on the

left side.

3 Adjust so that the clearance between the speakers is lost

and so that the speakers are not shifted to the right or left.

4 Fix the two points in the center of the display with screws.

5 Fix the two points on the right and left sides with screws.

Adjust so that the speaker system is parallel to the dis-

play and then finish securing the screws you had lightly

tightened on the mounting fittings.

When the speakers are installed

on the right and left sides

When the speakers are

installed at the bottom

CONNECTION TO A PLASMA

DISPLAY

1 Connecting the speaker cables

1 Switch off the power of the plasma display.

2 Connect the input terminals of the speaker system and

the speaker output terminals of the plasma display with

the accessory speaker cable. Make sure the positive (

ª)

and negative (

·) terminals match when connecting.

1. Push the lever, insert the cable into the hole, and release the lever.

To the

· terminal

To the

ª terminal

(Speaker input terminals of the speaker system)

· terminal (black) ª terminal (red)

Input terminal of speaker

White

White with gray line

÷ Make sure not to push on the speaker cover with force,

using your fingers or otherwise. The speaker cover can

be broken, and damage to the speaker unit may also

occur as a result.

NOTE:

÷ When attaching the speakers to the plasma display,

make sure to tighten all the screws, making sure the

speakers are secure and do not shake.

÷ When the display is to be moved after speaker

installation, do not hold the display by the speakers. Hold

the handle of the display and the side or bottom of the

display with reference to the figures below when moving

the speaker system. Do not hold the speakers and raise

the display. This may cause the deformation or damage

of products.

Make sure the speaker

is fit snug against the

bracket, then tighten

the screws.

2 Attach the speakers to the display.

Take care to ensure that the display does not hit the

speakers in steps 1 and 2 when speakers are installed on

the display.

1 Place it below the display while inclining one speaker and

insert it into the bracket on the right side.

English

2. For the output terminals on the plasma display, push the lever,

insert the cable into the hole, and release the lever.

÷ After connection to the terminals, pull lightly on the cable

to confirm that the tips of the cable are properly connected

to the terminals. An imperfect connection can cause

sound interruptions and noise.

÷ When cable cores stick out and ª and · lines are short-

circuited, an excessive load will be applied to the plasma

display and the operation will stop or trouble will be

caused.

2 How to route cables

Speed clamps are included with the plasma display for tidying your cables and keeping extra cable length out of the way.

When installing the speakers on the right and left sides of the display

Speed clamps

Speaker cable

When installing the speakers at the bottom of the display

A speaker cable or system cable is put in

the rack using a supplied wiring clamp so

that it cannot be viewed from the front.

Speaker cable

Wiring clamp

ª ··ª

Output terminal of plasma

display

Speaker cable

÷ When the polarity is reversed for one speaker (left or right)

at the time of connection to the plasma display, the bass

reproduction will be reduced, the sound positioning will

be lost, and a correct stereo effect will not be obtained.

÷ If you insert the speaker cord too far so that the insulation

is touching the speaker terminal, you may not get any

sound.

< right >

< wrong >