PIONEER PDP-S20-LR - Owner's Manual Immediate Download

PDP-S20-LR

Operating Instructions

Mode d'emploi

Bedienungsanleitung

Istruzioni per l'uso

Gebruiksaanwijzing

Manual de instrucciones

Speaker System

Enceintes acoustiques

Lautsprechersystem

Sistema di diffusori

Luidsprekersysteem

Sistema de altavoces

English

CHECKING THE ACCESSORIES

7 Speaker cable x 2

Thank you for buying this Pioneer product.

Please read through these operating instructions before

using your speaker system so you will know how to make

the most of its performance. After you have finished reading

the instructions, put them away in a safe place for future

reference.

BEFORE USE

÷ The nominal impedance of this speaker system is 8 ohms.

÷ In order to prevent damage to the speaker system

resulting from input overload, please observe the

following precautions:

÷ Do not supply power to the speaker system in

excess of the maximum permissable input. This

can result in damage or a possible fire hazard.

÷ When connecting or disconnecting pin-plugs, be

sure that amplifier power is OFF.

÷ When using a graphic equalizer to emphasize loud

sounds of a high frequency range, do not use

excessive amplifier volume.

÷ Do not force a low-powered amplifier to produce a

loud volume of sound (the amplifier's harmonic

distortion will be increased, and you may damage

the speaker).

÷ Please handle the speakers with sufficient care, as

the grille net and the cabinet can become damaged

or broken when they are subjected to strong external

impacts.

÷ Placing a CRT computer screen or CRT monitor near to

the speakers may result in interference or color distortion.

If this happens, distance the monitor from the speakers.

This product is designed for use with the PRO-910HD

Pioneer plasma display. For more information on

compatibility, please consult with your nearest Pioneer

authorized dealer or service center.

7 Operating Instructions

7 Speaker mounting fittings (Used when installing the

speakers flush with the display)

Holder for flush

mounting x 4

7 Speaker mounting fittings (Used when installing the

speakers set back from the display)

7 Speakers mounting screws

NOTE:

÷ Always use the accessory mounting fittings for

installation.

÷ When screws other than those enclosed as accessories

are used to install the speakers, the speakers may drop

off or accidents may be caused. Always use the screws

enclosed as accessories.

Notes on Installation Work:

This product is marketed assuming that it is installed by

qualified personnel with enough skill and competence.

Always have an installation specialist or your dealer install

and set up the product.

PIONEER cannot assume liabilities for damage caused

by mistake in installation or mounting, misuse,

modification or a natural disaster.

CAUTION

x 12

The customer can select whether to install the speakers flush

with the screen or set back slightly.

Flush

Set back

See the description below for details of the installation.

NOTE:

÷ If you install the speakers flush, you cannot use the

buttons on the right side of the display. Please use the

remote control.

Holder for set back

mounting x 4

WARNING:

Handling the power cord on this product or cords

associated with accessories sold with the product will

expoes you to lesd, a chemical known to the State of

California and other governmental entities to cause cancer

and birth defects or other reproductive harm.

Wash hands after handling.

English

2 Hang the speaker on the upper screw.

3 Fix the lower screw temporarily.

4 Adjust the position of the speaker and then fix the upper

and lower screws firmly.

5 Attach the left speaker following the same procedure as

described above.

INSTALLATION ON THE PLASMA

DISPLAY

CAUTION:

Attach the plasma display to the stand before installing

the speakers. See the Operating Instructions packed to-

gether with the stand for how to assemble the stand.

The illustrations show the holder for flush mounting, but

the explanations apply also for set back mounting.

Perform installation according to the following steps 1 to 2.

1 Attach the mounting fittings to the

speakers.

The illustration below shows the right speaker.

1 Align the convex portion of the holder for installing the

speakers on the right and left sides with the concave

portion of the speakers.

2 Fix the two points with screws.

3 Attach holders to the top and bottom of one speaker.

4 Similarly, attach two holders to

the top and bottom of the other

speaker.

2 Attach the speakers to the display.

The illustration below shows how to attach of the right speaker.

1 Fix the upper screw temporarily in advance to hang the

speaker on the display (In this case, leave a space of about

5 mm between the head of the screw and the display).

5mm

The display

NOTE:

÷ When the display is to be moved after speaker

installation, do not hold the display by the speakers. Hold

the display with one hand on the bottom of the unit and

the other on the handle on the rear. Do not hold the

speakers and raise the display. This may cause the

deformation or damage of products.

English

2 How to route cables

Speed clamps are included with the plasma display for

tidying your cables and keeping extra cable length out of the

way.

Speed clamps

Speaker cable

Use the supplied wiring clamp to hide

the cables from view.

Wiring clamp

CONNECTION TO A PLASMA DISPLAY

To the

· terminal

To the

ª terminal

(Speaker input terminals of the speaker system)

· terminal (black) ª terminal (red)

Input terminal of speaker

Black

Red

ª ··ª

Output terminal of plasma

display

1 Connecting the speaker cables

1 Switch off the power of the plasma display.

2 Connect the input terminals of the speaker system and

the speaker output terminals of the plasma display with

the accessory speaker cable. Make sure the positive (

ª)

and negative (

·) terminals match when connecting.

1. Push the lever, insert the cable into the hole, and release

the lever.

2. For the output terminals on the plasma display, push the

lever, insert the cable into the hole, and release the lever.

÷ After connection to the terminals, pull lightly on the cable

to confirm that the tips of the cable are properly con-

nected to the terminals. An imperfect connection can

cause sound interruptions and noise.

÷ When cable cores stick out and ª and · lines are short-

circuited, an excessive load will be applied to the plasma

display and the operation will stop or trouble will be

caused.

÷ When the polarity is reversed for one speaker (left or right)

at the time of connection to the plasma display, the bass

reproduction will be reduced, the sound positioning will

be lost, and a correct stereo effect will not be obtained.

English

· Organize cables together using the

speed clamps provided with the

plasma display.

Insert 1 into an appropriate hole on the rear of the unit, then

snap 2 into the back of 1 to fix the clamp.

Speed clamps are designed to be difficult to undo once in

place. Please attach carefully.

To remove speed clamps

Using pliers, twist the clamp 90° and pull it outward.

In some cases the clamp may have deteriorated over time

and may be damaged when removed.

SPECIFICATIONS

NOTE:

Specifications and design subject to possible modification

without notice, due to improvements.

Cabinet : Bass-reflex type

Used speakers (three-way system) :

Woofer (for low tones) ............................ Oval cone type

Tweeter (for high tones) ....................... 2 cm dome type

Super Tweeter (for high tones) ......... 2 cm ceramic type

Nominal impedance ..................................................... 8

Frequency Range ..................................... 60 to 20,000 Hz

Sensitivity ................................ 82 dB/W (at 1 m distance)

Permissible input :

Max. input ............................................................... 13 W

Rated input .............................................................. 4 W

Crossover frequency ................................................ 2 kHz

External Dimensions ....... 108 (W) x 652 (H) x 65 (D) mm

Weight ..................................................................... 1.7 kg

Accessory parts (for 2 speakers)

.............................................................. Speaker cable x 2

........................................................ Screw (M5 x 10) x 12

........................................... Holder for flush mounting x 4

..................................... Holder for set back mounting x 4

................................................ Operating Instructions x 1

Published by Pioneer Corporation.

CABINET MAINTENANCE

÷ Use a polishing cloth or dry cloth to wipe off dust and

dirt.

÷ When the cabinet is very dirty, wipe with a soft cloth

moistened with water-diluted cleanser; then wipe again

with a dry cloth. Do not use furniture wax or cleaners.

They may damage the surface of the cabinet.

÷ Never use thinner, benzine, insecticide sprays and other

chemicals on or near the cabinets, since these will cor-

rode the surfaces.

÷ When a chemical cloth is used, read the cautions for the

chemical cloth carefully.

To attach the speed clamps to the main unit

Connect the speed clamps using the 1 hole marked with ·

below, depending on the situation.