PIONEER PDP-S12-LR - Owner's Manual Immediate Download

PDP-S12-LR

Operating Instructions

Mode d'emploi

Bedienungsanleitung

Istruzioni per l'uso

Gebruiksaanwijzing

Manual de instrucciones

Speaker System

Enceintes acoustiques

Lautsprechersystem

Sistema di diffusori

Luidsprekersysteem

Sistema de altavoces

PDPS12LR.01-06/En

03.6.10, 1:50 PM

English

CHECKING THE ACCESSORIES

7 Speaker cable x 2

Thank you for buying this Pioneer product.

Please read through these operating instructions before

using your speaker system so you will know how to make

the most of its performance. After you have finished reading

the instructions, put them away in a safe place for future

reference.

BEFORE USE

÷ The nominal impedance of this speaker system is 8 ohms.

÷ In order to prevent damage to the speaker system

resulting from input overload, please observe the

following precautions:

÷ Do not supply power to the speaker system in

excess of the maximum permissable input. This

can result in damage or a possible fire hazard.

÷ When connecting or disconnecting pin-plugs, be

sure that amplifier power is OFF.

÷ When using a graphic equalizer to emphasize loud

sounds of a high frequency range, do not use

excessive amplifier volume.

÷ Do not force a low-powered amplifier to produce a

loud volume of sound (the amplifier's harmonic

distortion will be increased, and you may damage

the speaker).

÷ An automatic restore-type protective device is incorporated

to protect the speakers from excessive input signals or

abnormal signals. When an excessive input signal is sent

to the speakers, the protective device is activated and

loud high-pitched sounds will be prevented. In this case,

lower the volume of the plasma display during use. After

5 to 10 seconds, the speakers are restored automatically.

÷ Placing a CRT computer screen or CRT monitor near to

the speakers may result in interference or color distortion.

If this happens, distance the monitor from the speakers.

This product is designed exclusively for use with the

PDP-5040HD,PDP-504HDE,PDP-504HDG Pioneer plasma

display. For more information on compatibility, please

consult with your nearest Pioneer authorized dealer or

service center.

7 Operating Instructions

7 Speaker mounting fittings (Used when installing the

speakers on the right and left sides of the display)

Holder for installing

the speakers on

the right and left x 4

7 Speaker mounting fittings (Used when installing the

speakers at the bottom of the display)

7 Speakers mounting screws

NOTE:

÷ Always use the accessory mounting fittings for

installation.

÷ When screws other than those enclosed as accessories

are used to install the speakers, the speakers may drop

off or accidents may be caused. Always use the screws

enclosed as accessories.

Notes on Installation Work:

This product is marketed assuming that it is installed by

qualified personnel with enough skill and competence.

Always have an installation specialist or your dealer install

and set up the product.

PIONEER cannot assume liabilities for damage caused

by mistake in installation or mounting, misuse,

modification or a natural disaster.

CAUTION

x 12

The customer can select whether to install the speakers on

the right and left sides of the display or at the bottom of the

display.

When the speakers are installed

on the right and left sides

When the speakers are

installed at the bottom

See the description below for details of the installation.

CAUTION:

÷ Attach the plasma display to the stand (PDK-TS04) before

installing the speakers. See the Operating Instructions

packed together with the stand for how to assemble the

stand.

Bracket for installing the speakers at

the bottom x 2 for right and left sides

Bracket for installing the speakers

at the bottom x 1 for center

Rivet for installing the speakers at

the bottom x 2

WARNING:

Handling the power cord on this product or cords associated with accessories

sold with the product will expoes you to lesd, a chemical known to the State

of California and other governmental entities to cause cancer and birth defects

or other reproductive harm.

Wash hands after handling.

PDPS12LR.01-06/En

2003.6.13, 0:47 PM

English

INSTALLATION ON THE PLASMA

DISPLAY

(WHEN INSTALLING THE SPEAKERS ON THE RIGHT AND

LEFT SIDES OF THE DISPLAY)

1 Attach the mounting fittings to the

speakers.

The illustration below shows the right speaker.

1 Align the convex portion of the holder for installing the

speakers on the right and left sides with the concave

portion of the speakers.

2 Fix the two points with screws.

3 Attach holders to the top and bottom of one speaker.

4 Similarly, attach two holders to

the top and bottom of the other

speaker.

2 Attach the speakers to the display.

The illustration below shows how to attach of the right speaker.

1 Fix the upper screw temporarily in

advance to hang the speaker on

the display (In this case, leave a

space of about 5 mm between the

head of the screw and the display).

2 Hang the speaker on the upper

screw.

3 Fix the lower screw temporarily.

4 Adjust the position so that the speaker is parallel to the

display and then fix the upper and lower screws firmly.

Perform installation according to the following steps 1 to 2.

INSTALLATION ON THE PLASMA

DISPLAY

(WHEN INSTALLING THE SPEAKERS AT THE BOTTOM

OF THE DISPLAY)

1 Attach the mounting fittings to the

display.

1 Push rivets into each outside hole A of brackets (on the

right and left sides) for installing the speakers at the bottom.

2 Fix each outside hole B of brackets (on the right and left sides),

for installing the speakers at the bottom, with screws.

3 Insert the screws into the two outside holes of bracket

(at the center), for installing the speakers at the bottom,

and tighten them.

4 Align the bosses of the spacer with the holes of the stand

and insert them.

5mm

The display

Perform installation according to the following steps 1 to 2.

5 Attach the left speaker following the

same procedure as described above.

PDPS12LR.01-06/En

03.6.10, 1:50 PM

English

NOTE:

÷ When the display is to be moved after speaker

installation, do not hold the display by the speakers. Hold

the handle of the display and the side or bottom of the

display with reference to the figures below when moving

5 Fix the two points (four points in all) on the right and left

sides with screws. Adjust so that the speaker system is

parallel to the display and then fix the speaker system.

When the speakers are installed

on the right and left sides

When the speakers are

installed at the bottom

2 Attach the speakers to the display.

Take care to ensure that the display does not hit the

speakers in steps 1 and 2 when speakers are installed on

the display.

1 Place it below the display while inclining one speaker and

insert it into the bracket on the right side.

2 Similarly, insert the other speaker into the bracket on the

left side.

3 Adjust so that the clearance between the speakers is lost

and so that the speakers are not shifted to the right or left.

4 Fix the two points in the center of the display with screws.

CONNECTION TO A PLASMA

DISPLAY

1 Connecting the speaker cables

1 Switch off the power of the plasma display.

2 Connect the input terminals of the speaker system and

the speaker output terminals of the plasma display with

the accessory speaker cable. Make sure the positive (

ª)

and negative (

·) terminals match when connecting.

1. Push the lever, insert the cable into the hole, and release the lever.

2. For the output terminals on the plasma display, push the lever,

insert the cable into the hole, and release the lever.

÷ After connection to the terminals, pull lightly on the cable

to confirm that the tips of the cable are properly connected

to the terminals. An imperfect connection can cause

sound interruptions and noise.

÷ When cable cores stick out and ª and · lines are short-

circuited, an excessive load will be applied to the plasma

display and the operation will stop or trouble will be

caused.

÷ When the polarity is reversed for one speaker (left or right)

at the time of connection to the plasma display, the bass

reproduction will be reduced, the sound positioning will

be lost, and a correct stereo effect will not be obtained.

To the

· terminal

To the

ª terminal

(Speaker input terminals of the speaker system)

· terminal (black) ª terminal (red)

Input terminal of speaker

Black

Red

ª ··ª

Output terminal of plasma

display

the speaker system. Do not hold the speakers and raise

the display. This may cause the deformation or damage

of products.

PDPS12LR.01-06/En

03.6.10, 1:50 PM

English

2 How to route cables

Speed clamps are included with the plasma display for

tidying your cables and keeping extra cable length out of the

way.

· Organize cables together using the

speed clamps provided with the

plasma display.

Insert 1 into an appropriate hole on the rear of the unit, then

snap 2 into the back of 1 to fix the clamp.

Speed clamps are designed to be difficult to undo once in

place. Please attach carefully.

To remove speed clamps

Using pliers, twist the clamp 90° and pull it outward.

In some cases the clamp may have deteriorated over time

and may be damaged when removed.

When installing the speakers on the right and left sides of the display

Speed clamps

Speaker cable

When installing the speakers at the bottom of the display

A speaker cable or system cable is put in

the rack using a supplied wiring clamp so

that it cannot be viewed from the front.

Speaker cable

Wiring clamp

Speaker cable

To attach the speed clamps to the main unit

Connect the speed clamps using the 1 hole marked with ·

below, depending on the situation.

PDPS12LR.01-06/En

03.6.10, 1:50 PM