PIONEER PDP-S08 - Owner's Manual Immediate Download

PDP-S08

Operating Instructions

Mode d'emploi

Bedienungsanleitung

Istruzioni per l'uso

Gebruiksaanwijzing

Manual de instrucciones

Speaker System

Enceintes acoustiques

Lautsprechersystem

Sistema di diffusori

Luidsprekersysteem

Sistema de altavoces

English

CHECKING THE ACCESSORIES

7 Speaker cable x 2

Thank you for buying this Pioneer product.

Please read through these operating instructions before using

your speaker system so you will know how to make the

most of its performance. After you have finished reading the

instructions, put them away in a safe place for future

reference.

BEFORE USE

The nominal impedance of this speaker system is 8 ohms.

÷ In order to prevent damage to the speaker system

resulting from input overload, please observe the

following precautions:

÷ Do not supply power to the speaker system in

excess of the maximum permissable input. This

can result in damage or a possible fire hazard.

÷ When connecting or disconnecting pin-plugs, be

sure that amplifier power is OFF.

÷ When using a graphic equalizer to emphasize

loud sounds of a high frequency range, do not

use excessive amplifier volume.

÷ Do not force a low-powered amplifier to produce

a loud volume of sound (the amplifier's harmonic

distortion will be increased, and you may

damage the speaker).

÷ Please handle the speakers with sufficient care, as

the grille net and the cabinet can become dam-

aged or broken when they are subjected to strong

external impacts.

Placing a CRT computer screen or CRT monitor near to the

speakers may result in interference or color distortion. If this

happens, distance the monitor from the speakers.

CAUTION

This product is designed exclusively for use with the

PDP-4330HD,PDP-433HDE,PDP-433HDG Pioneer plasma

display.

7 Operating instructions

7 Speaker mounting fittings x 2

7 Speaker mounting bolts

· Flat countersunk head screw x 2

· Hexagon socket head screw x 2

7 Mounting tool (Hex wrench)

NOTE:

· Always use the accessory mounting fittings for

installation.

· When screws other than those enclosed as

accessories are used to install the speakers, the

speakers may drop off or accidents may be caused.

Always use the screws enclosed as accessories.

Notes on Installation Work:

This product is marketed assuming that it is installed

by qualified personnel with enough skill and compe-

tence. Always have an installation specialist or your

dealer install and set up the product.

PIONEER cannot assume liabilities for damage

caused by mistake in installation or mounting,

misuse, modification or a natural disaster.

7 Wire clamp x 2

CAUTION

AFTER THE SPEAKER HAS BEEN INSTALLED, DO

NOT HOLD IT OR USE IT FOR SUPPORT WHEN

MOVING THE DISPLAY. REMOVE THE SPEAKER

BEFORE MOVING.

English

INSTALLATION ON THE

PLASMA DISPLAY

Perform installation according to the following steps 1 to 7.

NOTE:

Before attaching the speaker, please attach the PDK-

TS01 table top stand (or another Pioneer plasma

display stand) to the plasma display unit.

1 Attach the speaker mounting fittings to

the rear of the plasma display.

Using the supplied hexagon socket head screws, fix

the speaker mounting fittings to the left and right

sides of the plasma display. (Use the supplied hex

wrench to tighten the screws.

Turn clockwise to tighten.

Align the lugs on the speaker mounting fittings

with the holes in the plasma display unit.

2 Connect the supplied speaker cords to

the back of the plasma display.

(Please also see the installation instructions of the

plasma display.)

3 Attach the two supplied wire clamps to

the rear of the speakers, as shown.

· The clamp opening should be pointing downward.

4 Connect the other end of the speaker

cords (see step 2) to the speakers.

See the following page for more detailed information

on connecting speaker cords.

5 Mount the speakers onto the speaker

mounting fittings.

To avoid damaging the stand, cover it with the

protective wrapping that covered the speaker.

Protective wrapping (the PDK-TS01 table top stand

only)

Carefully, mount the speaker onto the mounting

fittings.

6 Fix the speaker to the mounting fittings.

Use the supplied flat countersunk-head screws to fix

both right and left sides of the speaker to the

mounting fittings as shown below.

· Turn clockwise to tighten.

NOTE:

Do not use the screw hole located on the

underside of the mounting fittings to fix the

speaker.

This illustration

shows the PDK-

TS01 table top

stand.

This illustration

shows the PDK-TS01

table top stand.

This illustration shows

the PDK-TS01 table

top stand.

English

To the

· terminal

To the

ª terminal

(Speaker output terminals of the plasma display)

· terminal

ª terminal (red)

CABINET MAINTENANCE

Use a polishing cloth or dry cloth to wipe off dust

and dirt.

When the cabinet is very dirty, wipe with a soft

cloth moistened with water-diluted cleanser; then

wipe again with a dry cloth. Do not use furniture

wax or cleaners. They may damage the surface of

the cabinet.

Never use thinner, benzine, insecticide sprays and

other chemicals on or near the cabinets, since

these will corrode the surfaces.

When a chemical cloth is used, read the cautions

for the chemical cloth carefully.

The polarity of the input terminals is plus

ª for the

red terminal (the terminal on the right side in the

following figure) and minus

· for the black terminal

(the terminal on the left side in the following figure).

· After connection to the terminals, pull lightly on

the cable to confirm that the tips of the cable are

properly connected to the terminals. An imperfect

connection can cause sound interruptions and

noise.

CONNECTION TO A PLASMA

DISPLAY

1 Switch off the power of the plasma

display.

2 Use the supplied speaker cords to

connect the speaker outputs of the

plasma display to the speaker inputs on

the speaker system.

2. Push the lever, insert the

cable into the hole, and

release the lever.

1. Remove the insulation

and twist the core ends

together.

Published by Pioneer Corporation.

SPECIFICATIONS

Cabinet : Enclosed type

Used speakers (two-way system) :

Woofer (for low tones) .............................. Oval cone type

Tweeter (for high tones) ...................... 2.5 cm dome type

Nominal impedance ..................................................... 8

Frequency Range ..................................... 60 to 20,000 Hz

Sensitivity ................................ 82 dB/W (at 1 m distance)

Permissible input :

Max. input ................................................................. 12 W

Rated input ............................................................. 2.5 W

Crossover frequency ................................................ 3 kHz

External Dimensions ..... 1070 (W) x 74 (H) x 102 (D) mm

Weight ..................................................................... 2.7 kg

Accessory parts

Speaker cable .................................................................. 2

Wire clamp ...................................................................... 2

Flat countersunk head screw .......................................... 2

Hexagon socket head screw ........................................... 2

Mounting tool (Hex wrench) ........................................... 1

Speaker mounting fittings ............................................... 2

Operating Instructions .................................................... 1

NOTE:

Specifications and design subject to possible modification

without notice, due to improvements.

7 Route the speaker cords out of sight

from the front of the unit.

Route as shown in the diagram, using the wire

clamps (step 3) to secure the cords.

NOTE:

If you want to move the plasma display unit, make sure

that you remove the speaker first. In addition, do not

move the display holding on to the mounting fittings. This

can result in injury or damage to the unit.

When cable cores stick out and

ª and · lines are

short-circuited, an excessive load will be applied to

the plasma display and the operation will stop or

trouble will be caused.

Match the colors on the speaker cable with the

speaker terminals to ensure correct polarity. This

will result in correct stereo sound. Incorrect

polarity will result in poor, unfocused sound.

(black)

Black

Red

Françias

AVANT USAGE

Merci pour votre achat de cet appareil Pioneer.

Veuillez lire attentivement toutes ces instructions de

fonctionnement avant d'utiliser votre enceinte acoustique

de façon à pouvoir en tirer le meilleur profit. Après lecture

complète du livret d'instructions de fonctionnement, le

ranger dans un endroit sûr afin de pouvoir vous y reporter

facilement en cas de besoin lors de l'utilisation de l'enceinte

acoustique.

ATTENTION

÷ L'impédance nominale de cette enceinte acoustique est

de 8

÷ Afin d'éviter d'endommager l'enceinte acoustique,

suite à une surcharge à l'entrée, veuillez observer

les précautions suivantes:

÷ Ne pas fournir aux haut-parleurs une alimentation

supérieure à la valeur maximale admise, sinon

l'appareil risque d'être endommagé ou un incendie

pourrait éclater.

÷ En connectant ou en déconnectant les fiches à

plots, s'assurer que l'alimentation de l'amplificateur

est coupée sans faute.

÷ En utilisant un égalisateur graphique pour

accentuer les sons forts dans la plage des hautes

fréquences, ne pas régler l'amplificateur à un

volume excessif.

÷ Ne pas contraindre un amplificateur de faible

puissance à fonctionner à un volume sonore

poussé (la distorsion harmonique de l'amplificateur

sera accrue, ce qui risquerait d'endommager le

haut-parleur).

÷ Manipuler les haut-parleurs avec suffisamment de

soin, car autrement, l'enjoliveur frontal et le coffret

risqueraient d'être endommagés ou hors d'usage en

les soumettant à des chocs externes exagérés.

Ce produit est conçu exclusivement pour l'utilisation

avec un écran d'affichage au plasma Pioneer PDP-4330HD

ou PDP-433HDE.

7 Accessoires de montage de haut parleur x 2

7 Boulons de montage de haut parleur

Vis à tête fraisée plate x 2

Vis à tête hexagonale noyée x 2

7 Outil de montage (Clé hexagonale)

7 Mode d'emploi

V'ERIFICATIONDESACCESSOIRES

REMARQUE:

÷ Utilisez toujours les accessoires de montage pour

l'installation.

÷ Si des vis autres que ceux ci-joints sont utilisés pour in-

staller les haut-parleurs, ceux-ci peuvent se détacher et

tomber, ou des accidents risquent de se produire. Utilisez

toujours les vis ci-joints comme accessoires.

÷ Si un écran d'ordinateur à écran cathodique (CRT) ou un

moniteur à écran cathodique (CRT) est placé à proximité

des haut-parleurs, il risque de présenter des interférences

ou une dénaturation des couleurs. Dans ce cas, éloigner

le moniteur des haut-parleurs.

Remarques sur l'installation:

Ce produit est vendu en assumant qu'il sera installé par

un personnel suffisamment expérimenté et qualifié. Faites

toujours réaliser le montage et l'installation par un

spécialiste ou par votre revendeur.

PIONEER ne peut être tenu responsable pour tout

dommage causé par une erreur d'installation ou de

montage, une mauvaise utilisation ou un désastre naturel.

7 Câbles de haut-parleur x 2

7 Serre-fil x 2

ATTENTION

APRÈS L'INSTALLATION DE L'ENCEINTE

ACOUSTIQUE NE LE TENEZ PAS EN DÉPLAÇANT

L'ÉCRAN D'AFFICHAGE. RETIREZ ENCEINTE

ACOUSTIQUE AVANT DE DÉPLACER L'ÉCRAN

D'AFFICHAGE.

English