PIONEER PDP-42H1AN - Owner's Manual Immediate Download

Owner's Manual

PDP-42H1ENV

Multimedia Plasma Monitor

MODEL

PDP-42H1AN

PDP-42H1EN

CAUTION :

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS

VOLTAGE CONSTITUTING A RISK OF ELECTRIC

SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT

OPERATING AND MAINTENANCE INSTRUCTIONS IN THE

OWNER'S MANUAL WITH THIS UNIT.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Before operating this Plasma Monitor, read this manual thoroughly and operate the Plasma Monitor properly.

This Plasma Monitor provides many convenient features and functions. Operating the Plasma Monitor properly

enables you to manage those features and maintains it in better condition for a considerable time.

Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other

accidents.

If your Plasma Monitor seems to operate improperly, read this manual again, check operations and cable connections

and try the solutions in the "Trouble-shooting" section of the end of this booklet. If the problem still persists, contact

the sales dealer where you purchased the Plasma Monitor or the service center.

TO THE OWNER

SAFETY PRECAUTIONS

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

G This Plasma Monitor should be set in the way indicated. If not, it may result in a fire hazard.

G Take appropriate space on the top, sides and rear of the Plasma Monitor cabinet for allowing air circulation and

cooling the Plasma Monitor. Minimum distance should be taken. If the Plasma Monitor is to be built into a

compartment or similarly enclosed, the minimum distances must

be maintained. Do not cover the ventilation slot on the Plasma

Monitor. Heat build-up can reduce the life of your Plasma

Monitor, and can also be dangerous.

G If the Plasma Monitor is not to be used for an extended time,

unplug the Plasma Monitor from the power outlet.

READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.

SIDE and TOP

REAR

CAUTION IN INSTALLING

G Handle the Plasma Monitor carefully when installing it and do not drop.

G Locate set away from heat, excessive dust, and direct sunlight.

G For correct installation and mounting it is strongly recommended to use a trained, authorized dealer. Failure to

follow correct mounting procedures could result in damage to the equipment or injury to the installer.

10 cm

6 cm

NOTE :

When Plasma Monitor is not used for a long period of time, unlighting dots may be observed. This is caused by

characteristic of the Plasma Monitor. If this occurs, turn the Plasma Monitor on and leave it on about 1 hour. These

dots will gradually disappear.

SAFETY INSTRUCTIONS

All the safety and operating instructions should be read before

the product is operated.

Read all of the instructions given here and retain them for later

use. Unplug this

Plasma Monitor from AC power supply

before cleaning. Do not use liquid or aerosol cleaners. Clean

only with dry cloth.

Follow all warnings and instructions marked on the

Plasma

Monitor.

For added protection to the

Plasma Monitor during a

lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet. This will

prevent damage due to lightning and power line surges.

Do not expose this Plasma Monitor to rain or use near water...

for example, in a wet basement, near a swimming pool, etc...

The Plasma Monitor shall not be exposed to dripping or

splashing. No objects filled with liquids, such as vases, shall

be placed on the Plasma Monitor.

Only use attachments/accessories specified by the

manufacturer.

Do not place this

Plasma Monitor on an unstable cart, stand,

or table. The

Plasma Monitor may fall, causing serious injury

to a child or adult, and serious damage to the

Plasma

Monitor. Use only with a cart or stand recommended by the

manufacturer, or sold with the

Plasma Monitor.

CAUTION:

This

Plasma Monitor for use only with following Stand and

Mount Unit. Use with other stands or mount units is capable of

resulting in instability causing possible injury.

SANYO Table top stand

KA-TD-H10S

SANYO Tilt mount unit

KA-TI-H10

SANYO Wall mount unit

KA-WA-H10WV

SANYO Ceiling mount unit

KA-CH-H10

SANYO Floor Stand

KA-TD-42HW

An appliance and cart combination should

be moved with care.

Quick stops,

excessive force, and uneven surfaces

may cause the appliance and cart

combination to overturn.

Slots and openings in the back and top of the cabinet are

provided for ventilation, to insure reliable operation of the

equipment and to protect it from overheating.

Do not block any ventilation openings. Install in accordance

with the manufacturer's instructions. Do not install near any

heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

This

Plasma Monitor should not be placed in a built-in

installation such as a book case unless proper ventilation is

provided.

Never push objects of any kind into this

Plasma Monitor

through cabinet slots as they may touch dangerous voltage

points or short out parts that could result in a fire or electric

shock. Never spill liquid of any kind on the

Plasma Monitor.

This

Plasma Monitor should be operated only from the type

of power source indicated on the marking label. If you are not

sure of the type of power supplied, consult your authorized

dealer or local power company.

Do not overload wall outlets and extension cords as this can

result in fire or electric shock. Do not allow anything to rest on

the power cord. Protect the power cord from being walked on

or pinched particularly at plugs. convenience receptacles, and

the point where they exit from the apparatus.

Do not attempt to service this

Plasma Monitor yourself as

opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified

service personnel.

Unplug this

Plasma Monitor from wall outlet and refer

servicing to qualified service personnel under the following

conditions:

a. When the power cord or plug is damaged or frayed.

b. If liquid has been spilled into the

Plasma Monitor.

c. If the

Plasma Monitor has been exposed to rain or water.

d. If the

Plasma Monitor does not operate normally by

following the operating instructions. Adjust only those

controls that are covered by the operating instructions as

improper adjustment of other controls may result in damage

and will often require extensive work by a qualified

technician to restore the

Plasma Monitor to normal

operation.

e. If the

Plasma Monitor has been dropped or the cabinet

has been damaged.

f. When the

Plasma Monitor exhibits a distinct change in

performance-this indicates a need for service.

When replacement parts are required, be sure the service

technician has used replacement parts specified by the

manufacturer that have the same characteristics as the

original part. Unauthorized substitutions may result in fire,

electric shock, or injury to persons.

Upon completion of any service or repairs to this

Plasma

Monitor, ask the service technician to perform routine safety

checks to determine that the

Plasma Monitor is in safe

operating condition.

AC Power Cord has a grounding-type

AC line plug. This is a safety feature to

be sure that the plug will fit into the

power outlet. Do not try to defeat this

safety feature. Should you be unable to

insert the plug into the outlet, contact

your electrician.

Voor de klanten in Nederland

Bij dit product zijn batterijen

geleverd.

Wanneer deze leeg zijn,

moet u ze niet weggooien

maar inleveren als KCA.

GROUND

COMPLIANCES

AC Power Cord for the United Kingdom :

This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of

the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating,

marked thus

. If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse

cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse

covers are available from the Parts Department indicated in your User Instructions.

If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.

The end of the flexible cord should be suitably prepared and the correct plug fitted. (See Over)

WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET

OUTLET.

The Wires in this mains lead are coloured in accordance with the following code:

Green-and-yellow ············ Earth

Blue ································· Neutral

Brown ······························ Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the

letter E or by the safety earth symbol

or coloured green or green-and-yellow.

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

WARNING : THIS APPARATUS MUST BE EARTHED.

ASA

The AC Power Cord supplied with this Plasma Monitor meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada :

AC Power Cord used in the United States and Canada is listed by the Underwriters

Laboratories (UL) and certified by the Canadian Standard Association (CSA).

AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the

plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be

unable to insert the plug into the outlet, contact your electrician.

GROUND

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

AC POWER CORD REQUIREMENT

Declaration of Conformity

Model Number

: PDP-42H1EN/PDP-42H1ENV/PDP-42H1AN

Trade Name

: Sanyo

Responsible party

: SANYO FISHER COMPANY

Address

: 21605 Plummer Street, Chatsworth, California 91311

Telephone No.

: (818)998-7322

GThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

European Norm Compatibility / CE

This machine is provided with the CE-mark and therewith corresponding to the norms that are valid for its operation at

present. Thus the effective guidelines on the electromagnetic compatibility 89/336/EWG and safety regulations according

to low voltage guideline 73/23/EWG and 93/68/EWG are guaranteed. Mutual disturbances with other electronic appli-

ances are normally excluded, if those also are in accordance with valid norms. Sporadically disturbances cannot, howev-

er, be excluded. The product is in conformity with the directives of the valid European guidelines.

TABLE OF CONTENTS

FEATURES AND DESIGN

BEFORE OPERATION

COMPUTER MODE

VIDEO MODE

SETTING

APPENDIX

PREPARATION

NAME OF EACH PART OF PLASMA MONITOR 7

SETTING-UP PLASMA MONITOR

CONNECTING PLASMA MONITOR

TERMINALS OF PLASMA MONITOR

CONNECTING TO VIDEO EQUIPMENT

CONNECTING TO COMPONENT VIDEO EQUIPMENT

CONNECTING TO COMPUTER

OPERATION OF REMOTE CONTROL

OPERATING ON-SCREEN MENU

SELECTING INPUT SOURCE

SELECTING COMPUTER SYSTEM

PC ADJUSTMENT

SELECTING INPUT SOURCE

SELECTING VIDEO SYSTEM

SCREEN SAVER FUNCTION

SETTING MENU

CLEANING THE PLASMA MONITOR

TROUBLESHOOTING

FUNCTIONS OF PRODUCT SAFETY FEATURES

INFORMATION MENU

TECHNICAL SPECIFICATIONS

BASIC OPERATION

TRADEMARKS

G Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.

G IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

G Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its

respective corporation.

TURNING ON / OFF PLASMA MONITOR

OFF TIMER

SELECTING INPUT SOURCE

PICTURE IMAGE LEVEL SELECT

IMAGE LEVEL ADJUSTMENT

WIDE SCREEN OPERATIONS

SOUND ADJUSTMENT