Operating instructions
Mode d'emploi
Bedienungsanleitung
Istruzioni per l'uso
Gebruiksaanwijzing
Manual de instrucciones
Table top stand
Pied de table
Tischständer
Supporto di tavolo
Tafelbladstaander
Soporte de mesa
PDK-TS14
2
En
Thank you for buying Pioneer's product.
Please read through the Operating Instructions to learn
how to operate your model safely and properly.
Please be advised to keep the Operating Instructions in
your place for future reference.
Contents
Cautions ................................................................... 2
Checking the Standard Accessories ...................... 3
Assembling the Stand ............................................ 3
Attaching the Plasma Display ................................ 4
Installing the Product on a Rack etc. ..................... 4
Preventing Equipment from Falling Over ............. 5
Specifications .......................................................... 6
Dimensions Diagram .............................................. 6
Installation
¶ Consult your dealer if you encounter any difficulties
with this installation.
¶ Pioneer is not liable for any damage resulting from
improper installation, improper use, modification, or
natural disasters.
Cautions
This product is a table top stand exclusively designed for
Plasma Displays (PDP-436RXE / PDP-436SXE) from
Pioneer. Use with other model is capable of resulting in
instability causing possible injury. For further information,
please contact the store where you purchased your display.
Do not install or modify the product other than specified.
Do not use this stand for a Plasma Display other than those
designated and do not modify it or use it for other
purposes.
Improper installation is extremely dangerous because it
may result in it falling over or other accident.
Installation Location
· Select a location that is strong enough to support the
weight of the stand and the displays.
· Make sure to place it in a level and stable location.
· Do not install it outdoors, at a hot spring, or near a beach.
· Do not install the stand where it may be subjected to
vibration or shock.
Assembling and Installation
· Assemble the stand in accordance with the assembly
instructions and securely attach all screws at the
designated locations.
There have been cases where unforeseen accidents
such as the equipment breaking or falling over
occurred after the installation of the display because
the stand was not installed as instructed.
· The display must always be installed by two or more
people to assure it is installed safely.
· Before installation, turn off the power for the display
and peripheral devices then remove the power cord
plug from the power outlet.
Prevent accidents caused by the product falling over by
taking reliable measures to prevent it from falling over (see
Page 5).
CAUTION
This symbol refers to a hazard or unsafe practice which
can result in personal injury or property damage.
IMPORTANT NOTICE
Record the model number and serial number of this
equipment below.
Model No. PDK-TS14
Serial No.
Keep these numbers for future use.
3
En
English
Checking the Standard Accessories
Check to make sure that you have all the standard accessories before assembly and installation.
Base cover x 1
Stand pipes
(left and right, interchangeable) x 2
Hexagonal wrench x 1
(Diagonal size: 6 mm)
Screws 1 (4 x 10 mm) x 4
Installation bolts 3
(M8 x 30 mm: silver) x 2
Installation bolts 2
(M8 x 60 mm: silver) x 2
Operating instructions
(this document) x 1
Assembling the Stand
1 Turn the base cover over so the
underside is facing up.
2 Insert the stand pipes into the base
cover.
3 Tighten the screws to stabilize the
stand pipes.
Base cover
Screws 1
(4 x 10 mm)
Stand pipe
Screws 1
(4 x 10 mm)
Stand pipe
Assembly Procedure
Operating instructions
Mode d'emploi
Bedienungsanleitung
Istruzioni per l'uso
Gebruiksaanwijzing
Manual de instrucciones
Table top stand
Pied de table
Tischständer
Supporto di tavolo
Tafelbladstaander
Soporte de mesa
PDK-TS14
4
En
Installation bolts 3
(M8 x 30 mm: silver)
Attaching the Plasma Display
The weight of a 43 inch model is about 32 kg (70.4
lbs), they have no depth, and are unstable.
Therefore, at least two people must assemble and
install them.
Note
Be sure to install it on a flat stable location.
Insert the screws in the holes vertically and do not tighten
them with more force than necessary.
Attachment Method
1 Attaching the Plasma Display to the stand.
Fit the stand's support columns to the bottom of the
Plasma Display as indicated by the arrows, then slowly
insert them vertically. Be extremely careful not to insert the
support columns of the stand into any part of the Plasma
Display other than the stand insertion slots. Note that doing
so might damage the Plasma Display panel or its ports or
result in the warping of the stand.
Line up the column
supports with the bottom
of the Plasma Display as
indicated in the accompa-
nying diagram.
3 Securing the Plasma Display with
Installation bolts 3.
Secure them using the enclosed hexagonal wrench.
2 Securing the Plasma Display with
Installation bolts 2.
Attach the Plasma Display at the points indicated by the
arrows using the enclosed hexagonal wrench.
Installation bolts 2
(M8 x 60 mm: silver)
Caution
Installing the Product on a Rack etc.
When installing on a rack etc., hold the Plasma
Display.
Caution
5
En
English
12 to 15 mm
(1/2 to 5/8 inch)
M8
Using a wall for stabilization
1 Attaching falling prevention bolts (hooks)
to the Plasma Display.
2 Using strong cords or chains to stabilize it
appropriately and firmly to a wall, pillar, or
other sturdy element.
Perform this work in the same way on the left and right
sides.
Note
Use hooks, ropes, chains, and
fittings that are available on the
market.
Recommended hook:
Nominal diameter M8
Length 12 to 15 mm (1/2 to 5/8 inch)
1 Hook
2 Cord or chain
Fitting
Stabilizing on table or floor
Stabilize the equipment as shown in the diagram using
screws that are available on the market.
Note
To stabilize the equipment on a
table or on the floor, use
screws that have a nominal
diameter of 6 mm (1/4 inch)
and that are at least 20 mm
(13/16 inch) long.
After installing the stand, be sure to take special care to ensure that the equipment will not fall over.
Position of table/floor screws
When stabilizing the stand to a table or the floor, use
nominal diameter 6 mm (1/4 inch) with a length above 20
mm (13/16 inch).
Unit: mm (inch)
Preventing Equipment from Falling Over
· A table or an area of the floor with adequate strength
should always be used to support the Plasma Display.
Failure to do so could result in personal injury and
physical damage.
· When installing the Plasma Display, please take the
necessary safety measures to prevent it from falling or
overturning in case of emergencies, such as
earthquakes, or of accidents.
· If you do not take these precautions, the Plasma
Display could fall down and cause injury.
· The screws, hooks, chains and other fittings that you
use to secure the Plasma Display to prevent it from
overturning will vary according to the composition and
thickness of the surface to which it will be attached.
· Select the appropriate screws, hooks, chains and other
fittings after first inspecting the surface carefully to
determine its thickness and composition and after
consulting a professional installer if necessary.
Min. 20 mm
(13/16 inch)
6
mm
(1/4
inch)
9
to
15
mm
(3/8
to
5/8
inch)
249
(9-13/16)
24
(1)
120
(4-23/32)
478
(18-13/16)
Side View
11
(13/32)
Caution