ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2007
DVR-555HX-S
RRV3676
HDD/DVD RECORDER
DVR-555HX-S
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
This service manual should be used together with the following manual(s):
Model
Type
Power Requirement
Region No.
Serial No.
Please confirm 3rd & 4th
alphabetical letters.
DVR-555HX-S
WYXK5
AC 220 V to AC 240 V
2
&&UK######$$
Model
Order No.
Remarks
DVR-LX60D/WYXK5
RRV3573
T-ZZA-001 OCT. 2007 printed in Japan
DVR-555HX-S
2
12
34
1
234
C
D
F
A
B
E
1. CONTRAST OF MISCELLANEOUS PARTS
1.1 CONTRAST TABLE
DVR-550HX-S/WYXK5 and DVR-555HX-S/WYXK5 are constructed the same except for the following:
*1: Refer to SERVICE DVUB Assy (VXX3231) for DVR-LX60.
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The
mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Screws adjacent to
mark on product are used for disassembly.
For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions, apply as you think it appropriate.)
Nos. indicate the pages and Nos. in the service manual for the base model.
NOTES:
When ordering resistors, first convert resistance values into code form as shown in the following examples.
Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%,
and K=10%).
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors).
561
473
R50
1R0
5621
560
47k
0.5
1
RD1/4PU
J
RD1/4PU
J
RN2H
K
RS1P
K
56
x 10 1
47
x 10 3
R50
1R0
561
473
5.62k
RN1/4PC
F
562
x 10 1
5621
Mark
No.
Symbol and Description
DVR-550HX-S/
WYXK5
DVR-555HX-S/
WYXK5
Remarks
PCB ASSEMBLIES
NSP
1.. TUJB ASSY
VWM2436
VWM2425
P97-2
2.. SERVICE DVUB Assy
VXX3232
VXX3231
*1
PACKING SECTION
P95-3
RF Anttenna Cable (PAL)
VDE1075
VDE1095
P95-9
Packing Case
VHG2795
VHG2873
P95-12
Operating Instructions (French)
VRC1378
VRC1446
P95-13
Operating Instructions (German)
VRC1383
VRC1448
P95-14
Operating Instructions (Italian)
VRC1387
VRC1450
P95-15
Operating Instructions (Dutch)
VRC1391
VRC1452
P95-16
Operating Instructions (Spanish)
VRC1395
VRC1454
EXTERIOR SECTION
P97-25
Housing Assy 10P
Not used
VKP2391
DVUB Assy -
MAIN Assy
P97-27
Rear Panel
VNA3020
VNA3052
FRONT PANEL SECTION
P101-17
Front Panel
VNK6221
VNK6334
P101-20
FL Lens
VXA2870
VXA2930
ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2007
HDD/DVD
DivX
COPY
HDMI
OPEN/CLOSE
STANDBY/ON
USB
DV IN
CH
INPUT
SELECT
STOP REC
ONE TOUCH
COPY
INPUT 2
VIDEO
S-VIDEO
L(MONO)
R
AUDIO
REC
A.TV/D.TV
COMMON INTERFACE
PLTV
D.TV
A.TV
DVR-LX60D
RRV3573
DVD RECORDER
DVR-LX60D
DVR-LX60D-AV
DVR-550HX-S
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model
Type
Power Requirement
Region No.
Serial No.
Please confirm 3rd & 4th
alphabetical letters.
DVR-LX60D
WYXK5
AC 220 V to 240 V
2
&&UK######$$
DVR-LX60D
WVXK5
AC 220 V to 240 V
2
&&UK######$$
DVR-LX60D
YXKRE5
AC 220 V to 240 V
5
&&UK######$$
DVR-LX60D-AV
WYXK5
AC 220 V to 240 V
2
&&UK######$$
DVR-550HX-S
WYXK5
AC 220 V to 240 V
2
&&UK######$$
DVR-550HX-S
WVXK5
AC 220 V to 240 V
2
&&UK######$$
DVR-550HX-S
YXKRE5
AC 220 V to 240 V
5
&&UK######$$
For details, refer to "Important Check Points for good servicing".
T-FZA-001 MAY 2007 printed in Japan
DVR-LX60D
2
12
34
1
234
C
D
F
A
B
E
SAFETY INFORMATION
LABEL CHECK
WARNING!
The laser component is capable of emitting radiation exceeding
the limit for CLASS 1. A specially instructed person should do
servicing operation of the apparatus.
Laser Pickup specifications and
Laser characteristics
For CD
Wave length : 785 nm
Operating output :
Read mode : 1.07 mW (CW), Class1
Maximum output : Class1M
For DVD
Wave length : 660 nm
Operating output :
Read mode : 1.08 mW, Class1
Write mode : 21.89 mW (Pulse), Class1M
Maximum output : Class2M
CLAMP signals for detecting the loading state are detected
by the drive CPUs, and the design prevents laser diode
oscillation when the CLAMP signal turns OFF.
In normal operation, if no disc is clamped, the laser diode
oscillation is disabled.
However, the interlock does not always operate in the
"LD Degration Judgment of ATA/ATAPI DEBUG OSD" and
"LD POWER ADJUSTMENT"*.
2. When the cover is opened, close viewing of the objective
lens with the naked eye will cause exposure to a Class 3A
laser beam.
* Refer to Pages 49 and 79.
Additional Laser Caution
1. The ON/OFF(ON:low level,OFF:high level) status of the
VRW2262
STA
ND
BY
/ON
REC
DVR-LX60D
3
56
7
8
56
7
8
C
D
F
A
B
E
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.