ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2005
DJM-1000
RRV3121
DJ MIXER
DJM-1000
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model
Type
Power Requirement
Remarks
DJM-1000
KUCXJ
AC120V
DJM-1000
WYXJ
AC220-240V
DJM-1000
RLTXJ
AC110-120V / 220-240V
For details, refer to "Important Check Points for good servicing".
T-ZZY APR 2005 printed in Japan
DJM-1000
2
12
34
12
3
4
C
D
F
A
B
E
SAFETY INFORMATION
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service
technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground
(water pipe, conduit, etc.) by connecting a leakage
current tester such as Simpson Model 229-2 or
equivalent between the earth ground and all exposed
metal parts of the appliance (input/output terminals,
screwheads, metal overlays, control shaft, etc.). Plug
the AC line cord of the appliance directly into a 120V
AC 60 Hz outlet and turn the AC power switch on. Any
current measured must not exceed 0.5 mA.
ANY MEASUREMENTS NOT WITHIN THE LIMITS
OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL
SHOCK HAZARD AND MUST BE CORRECTED BEFORE
RETURNING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related characteristics. These are
often not evident from visual inspection nor the protection
afforded by them necessarily can be obtained by using
replacement components rated for voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this Service Manual.
Electrical components having such features are
identified by marking with a > on the schematics and on
the parts list in this Service Manual.
The use of a substitute replacement component which
does not have the same safety characteristics as the
PIONEER recommended replacement one, shown in the
parts list in this Service Manual, may create shock, fire,
or other hazards.
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER Service
Manual. A subscription to, or additional copies of,
PIONEER Service Manual may be obtained at a nominal
charge from PIONEER.
Leakage
current
tester
Reading should
not be above
0.5 mA
Device
under
test
Test all
exposed metal
surfaces
Also test with
plug reversed
(Using AC adapter
plug as required)
Earth
ground
AC Leakage Test
(FOR USA MODEL ONLY)
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to
cause cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols
(fast operating fuse) and/or
(slow operating fuse) on PCB indicate that replacement parts must
be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible
(fusible de type rapide) et/ou
(fusible de type lent) sur CCI indiquent que les pièces
de remplacement doivent avoir la même désignation.
This service manual is intended for qualified service technicians ; it is not meant for the casual do-it-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
DJM-1000
3
56
78
56
7
8
C
D
F
A
B
E
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
0 Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.
DJM-1000
4
12
34
12
3
4
C
D
F
A
B
E
CONTENTS
1. SPECIFICATIONS ............................................................................................................................................ 5
2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 6
2.1 PACKING SECTION .................................................................................................................................. 6
2.2 BOTTOM SECTION ................................................................................................................................... 8
2.3 CONTROL PANEL SECTION .................................................................................................................. 10
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ..........................................................................................12
3.1 BLOCK DIAGRAM ................................................................................................................................... 12
3.2 OVERALL WIRING DIAGRAM (1/2) ........................................................................................................ 14
3.3 OVERALL WIRING DIAGRAM (2/2) ........................................................................................................ 16
3.4 DIGITAL MAIN ASSY (1/4)....................................................................................................................... 18
3.5 DIGITAL MAIN ASSY (2/4)....................................................................................................................... 20
3.6 DIGITAL MAIN ASSY (3/4)....................................................................................................................... 22
3.7 DIGITAL MAIN ASSY (4/4)....................................................................................................................... 24
3.8 CH1/CH2 INPUT ASSY ........................................................................................................................... 26
3.9 CH3/CH4 INPUT ASSY ........................................................................................................................... 28
3.10 CH5/CH6 INPUT ASSY ......................................................................................................................... 30
3.11 SEND/RETURN ASSY .......................................................................................................................... 32
3.12 BOOTH/REC ASSY ............................................................................................................................... 34
3.13 MASTER ASSY ..................................................................................................................................... 36
3.14 MIC, MIC VR and HP ASSYS ................................................................................................................ 38
3.15 DIGITAL SUB ASSY............................................................................................................................... 40
3.16 VISUAL LINK and MASTER FADER ASSYS.........................................................................................42
3.17 BUS1 ASSY ........................................................................................................................................... 44
3.18 BUS2 ASSY ........................................................................................................................................... 46
3.19 PANEL1 ASSY ....................................................................................................................................... 48
3.20 PANEL2 and ISOLATOR ASSYS ........................................................................................................... 50
3.21 PANEL3 ASSY ....................................................................................................................................... 52
3.22 CH1/CH3/CH5 FADER, CH2/CH4/CH6 FADER and CROSS FADER ASSYS ..................................... 54
3.23 ACIN, POWER, REG1 and REG2 ASSYS............................................................................................. 56
3.24 VOLTAGES ............................................................................................................................................. 58
3.25 WAVEFORMS ........................................................................................................................................ 65
4. PCB CONNECTION DIAGRAM ..................................................................................................................... 75
4.1 DIGITAL MAIN ASSY ............................................................................................................................... 76
4.2 CH1/CH2 INPUT and CH3/CH4 INPUT ASSYS...................................................................................... 80
4.3 CH5/CH6 INPUT and SEND/RETURN ASSYS ....................................................................................... 82
4.4 BOOTH/REC and MASTER ASSYS ........................................................................................................ 84
4.5 MIC, MIC VR, HP and DIGITAL SUB ASSYS .......................................................................................... 86
4.6 VISUAL LINK, MASTER FADER, PANEL2 and ISOLATOR ASSYS........................................................ 88
4.7 BUS1 ASSY ............................................................................................................................................. 92
4.8 BUS2 ASSY ............................................................................................................................................. 94
4.9 PANEL1 ASSY ......................................................................................................................................... 96
4.10 PANEL3 ASSY ..................................................................................................................................... 100
4.11 CH1/CH3/CH5 FADER, CH2/CH4/CH6 FADER and CROSS FADER ASSYS ................................... 104
4.12 ACIN, POWER, REG1 and REG2 ASSYS........................................................................................... 106
5. PCB PARTS LIST ......................................................................................................................................... 110
6. ADJUSTMENT ............................................................................................................................................. 119
7. GENERAL INFORMATION ........................................................................................................................... 120
7.1 DIAGNOSIS ........................................................................................................................................... 120
7.1.1 TEST MODE .................................................................................................................................... 120
7.1.2 POWER ON SEQUENCE................................................................................................................ 128
7.1.3 TROUBLE SHOOTING .................................................................................................................... 129
7.1.4 DISASSEMBLY................................................................................................................................ 130
7.2 PARTS.................................................................................................................................................... 139
7.2.1 IC ..................................................................................................................................................... 139
8. PANEL FACILITIES ...................................................................................................................................... 163
DJM-1000
5
56
78
56
7
8
C
D
F
A
B
E
1. SPECIFICATIONS
1. General Specifications
Power supply voltage (KUCXJ) ..............................AC 120 V, 60 Hz
Power supply voltage (WYXJ) ...................AC 220-240 V, 50/60 Hz
Power supply voltage (RLTXJ) ....AC 110-120 V/220-240 V, 50/60 Hz
Power consumption (KUCXJ) ...................................................63 W
Power consumption (WYXJ, RLTXJ) ........................................62 W
Operating temperature ...................+5
°C to +35°C (+41°F to +95°F)
Operating humidity ...........................5 % to 85 % (no condensation)
Weight ..............................................................12.1 kg (26 lb 11 oz)
External dimensions ................482 (W) x 359.3 (D) x 187.5 (H) mm
(19 (W) x 14-5/16 (D) x 7-3/8 (H) in)
2. Audio Section
Sampling rate .........................................................................96 kHz
A/D, D/A converter .................................................................24 bits
Frequency response ................................................20 Hz to 20 kHz
S/N ratio (at full scale)
LINE .................................................................................104 dB
PHONO ..............................................................................88 dB
MIC .....................................................................................84 dB
Distortion (LINE-MASTER1) ................................................0.005 %
Headroom.................................................................................19 dB
Input level
PHONO .............................................................52 dBu (47 k
)
MIC, SUBMIC.......................................................52 dBu (3 k
)
CD/LINE, LINE ..................................................12 dBu (22 k
)
RETURN ............................................................12 dBu (22 k
)
Output level
MASTER1 ...........................................................+2 dBu (600
)
MASTER2 ...........................................................+2 dBu (10 k
)
REC .....................................................................8 dBu (10 k
)
BOOTH ...............................................................+2 dBu (600
)
SEND .................................................................12 dBu (10 k
)
PHONES ............................................................+8.5 dBu (32
)
Crosstalk (LINE) ......................................................................88 dB
Channels .........................................................................................6
Channel equalizer
HI .........................................................26 dB to +6 dB (13 kHz)
MID ........................................................26 dB to +6 dB (1 kHz)
LOW.......................................................26 dB to +6 dB (70 Hz)
Microphone equalizer
HI ...........................................................6 dB to +6 dB (10 kHz)
LOW.......................................................6 dB to +6 dB (100 Hz)
Booth monitor equalizer
HI ...........................................................6 dB to +6 dB (10 kHz)
LOW.......................................................6 dB to +6 dB (100 Hz)
3. Input output connectors
PHONO input connectors
RCA pin jack ..............................................................................6
CD/LINE, LINE input connectors
RCA pin jack ..............................................................................6
Phone jack (
6.3 mm) .....................................................................4
MIC, SUBMIC input connectors
XLR connector/Phone jack (
6.3 mm) .......................................1
Phone jack (
6.3 mm) ................................................................2
DIGITAL coaxial input connectors
RCA pin jack ..............................................................................4
RETURN input connectors
Phone jack (
6.3 mm) ................................................................2
MASTER output connectors
XLR connector............................................................................1
RCA pin jack ..............................................................................1
BOOTH output connectors
Phone jack (
6.3 mm) ................................................................2
REC output connectors
RCA pin jack ..............................................................................1
SEND output connectors
Phone jack (
6.3 mm) ................................................................2
DIGITAL coaxial output connector
RCA pin jack ..............................................................................1
Digital link connectors (EFX 1, 2, SOUND 1, 2, VISUAL)
Mini DIN .....................................................................................5
MIDI OUT connector
5P DIN .......................................................................................1
4. Accessories
Operating instructions .....................................................................1
Power cord ......................................................................................1
Warranty (KUCXJ only) ...................................................................1
Appearance and specifications are subject to change without
notice.
Power cord
(KUCXJ : DDG1028)
(WYXJ, RLTXJ : ADG7062)
Accessories
Operating Instructions
Warranty (KUCXJ type only)