ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2004
DEH-P960MP/XN/UC
CRT3191
MULTI-CD CONTROL DSP HIGH POWER CD/MP3/WMA PLAYER WITH FM/AM TUNER
DEH-P960MP
/XN/UC
DEH-P9600MP/XN/UC
DEH-P9650MP/XN/ES
This service manual should be used together with the following manual(s):
Model No.
Order No.
Mech.Module
Remarks
CX-3098
CRT3179
S10WMAcode2
CD Mech. Module:Circuit Description, Mech. Description, Disassembly
For details, refer to "Important symbols for good services".
K-ZZU.FEB. 2004 printed in Japan
DEH-P960MP/XN/UC
2
1234
123
4
C
D
F
A
B
E
SAFETY INFORMATION
- CD Section Precaution
1. Before disassembling the unit, be sure to turn off
the power. Unplugging and plugging the connectors
during power-on mode may damage the ICs inside
the unit.
2. To protect the pickup unit from electrostatic discharge
during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY"
on page 68.
3. After replacing the pickup unit, be sure to check the
grating. (See p.64.)
CAUTION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the
If you are not qualified to perform the repair of this product properly and safely, you should not risk
and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the
of California to cause cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
repair
warranty.
trying to do so
state
This product contains mercury. Disposal of this material may be regulated due to
environmental considerations. For disposal or recycling information, please contact
your local authorities or the Electronics Industries Alliance: www.eiae.org.
ES
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type.
Battery
Slide the tray out on the back of the
remote controller and insert the battery
with the (+) and () poles pointing in
the proper direction.
Note :
· Use a CR2025 (3V) lithium battery
only. Never use other types of battery
with this unit.
DEH-P960MP/XN/UC
3
5
678
56
7
8
C
D
F
A
B
E
[ Important symbols for good services ]
In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely.
When you find the procedures bearing any of the symbols, be sure to fulfill them:
2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable.
In accordance with the procedures or instructions described in this manual, adjustments should be performed.
3. Cleaning
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning,
proper cleaning should be performed to restore their performances.
5. Lubricants, glues, and replacement parts
Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying
glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the
prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed
ones should be used.
4. Shipping mode and shipping screws
To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or
the shipping screws should be installed before shipping out in accordance with this manual, if necessary.
1. Product safety
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and
should keep the safety during servicing by following the safety instructions described in this manual.
DEH-P960MP/XN/UC
4
1234
123
4
C
D
F
A
B
E
CONTENTS
SAFETY INFORMATION ..................................................................................................................................... 2
1. SPECIFICATIONS ............................................................................................................................................ 5
2. EXPLODED VIEWS AND PARTS LIST .......................................................................................................... 10
2.1 PACKING(UC MODEL) ............................................................................................................................ 10
2.2 PACKING(ES MODEL) ............................................................................................................................ 12
2.3 EXTERIOR(1) .......................................................................................................................................... 14
2.4 EXTERIOR(2) .......................................................................................................................................... 16
2.5 CD MECHANISM MODULE..................................................................................................................... 18
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ..........................................................................................20
3.1 BLOCK DIAGRAM ................................................................................................................................... 20
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE).............................................................................. 22
3.3 KEYBOARD UNIT(OEL) .......................................................................................................................... 28
3.4 KEYBOARD UNIT(LCD) .......................................................................................................................... 30
3.5 CD MECHANISM MODULE(GUIDE PAGE) ............................................................................................ 32
4. PCB CONNECTION DIAGRAM ..................................................................................................................... 42
4.1 TUNER AMP UNIT................................................................................................................................... 42
4.2 KEYBOARD UNIT(OEL) .......................................................................................................................... 46
4.3 KEYBOARD UNIT(LCD) .......................................................................................................................... 47
4.4 CD MECHANISM MODULE..................................................................................................................... 48
4.5 SWITCH PCB .......................................................................................................................................... 50
4.6 CONNECTOR PCB.................................................................................................................................. 51
5. ELECTRICAL PARTS LIST ............................................................................................................................ 52
6. ADJUSTMENT ............................................................................................................................................... 61
6.1 JIG CONNECTION DIAGRAM................................................................................................................. 61
6.2 CD ADJUSTMENT................................................................................................................................... 62
6.3 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT .................................................... 64
6.4 ERROR MODE ........................................................................................................................................ 66
6.5 FREQUENCY CHECK FOR CLOCK ....................................................................................................... 67
6.6 OEL SCREENSAVER STUDIO IKA TO LKD APPLICATION :GGV1168................................................. 67
7. GENERAL INFORMATION ............................................................................................................................. 68
7.1 DIAGNOSIS ............................................................................................................................................. 68
7.1.1 DISASSEMBLY ..................................................................................................................................... 68
7.1.2 CONNECTOR FUNCTION DESCRIPTION .......................................................................................... 76
7.2 PARTS...................................................................................................................................................... 77
7.2.1 IC .......................................................................................................................................................... 77
7.2.2 DISPLAY ............................................................................................................................................... 91
7.3 OPERATIONAL FLOW CHART ............................................................................................................... 92
7.4 CLEANING............................................................................................................................................... 93
8. OPERATIONS ................................................................................................................................................ 94
DEH-P960MP/XN/UC
5
5
678
56
7
8
C
D
F
A
B
E
1. SPECIFICATIONS