PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC.
P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A.
PIONEER EUROPE NV
Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936
C PIONEER CORPORATION 2001
K-ZZY. DEC. 2001 Printed in Japan
DEH-P6400R
XN/EW
- This service manual should be used together with the following manual(s):
Model No.
Order No.
Mech. Module Remarks
CX-977
CRT2624
S9
CD Mech. Module:Circuit Description, Mech.Description, Disassembly
CONTENTS
1. SAFETY INFORMATION ............................................3
2. EXPLODED VIEWS AND PARTS LIST .......................4
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ...10
4. PCB CONNECTION DIAGRAM ................................24
5. ELECTRICAL PARTS LIST ........................................32
6. ADJUSTMENT..........................................................38
7. GENERAL INFORMATION .......................................47
7.1 DIAGNOSIS ........................................................47
7.1.1 DISASSEMBLY .........................................47
7.1.2 CONNECTOR FUNCTION DESCRIPTION .......51
7.2 IC ........................................................................52
7.3 OPERATIONAL FLOW CHART ...........................62
7.4 CLEANING ..........................................................63
8. OPERATIONS AND SPECIFICATIONS.....................64
For details, refer to "Important symbols for good services".
ORDER NO.
CRT2806
MULTI-CD/DAB CONTROL HIGH POWER CD PLAYER WITH RDS TUNER
Service
Manual
2
DEH-P6400R
- CD Player Service Precautions
1. For pickup unit(CXX1480) handling, please refer
to"Disassembly"(see page 47)
During replacement, handling precautions shall be
taken to prevent an electrostatic discharge(protection
by a jumper-solder).
2. During disassembly, be sure to turn the power off
since an internal IC might be destroyed when a con-
nector is plugged or unplugged.
3. Please checking the grating after changing the ser-
vice pickup unit(see page 41).
[ Important symbols for good services ]
In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely.
When you find the procedures bearing any of the symbols, be sure to fulfill them:
2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable.
In accordance with the procedures or instructions described in this manual, adjustments should be performed.
3. Cleaning
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning,
proper cleaning should be performed to restore their performances.
5. Lubricants, glues, and replacement parts
Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying
glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the
prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed
ones should be used.
4. Shipping mode and shipping screws
To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or
the shipping screws should be installed before shipping out in accordance with this manual, if necessary.
1. Product safety
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and
should keep the safety during servicing by following the safety instructions described in this manual.
3
DEH-P6400R
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
1. Safety Precautions for those who Service this Unit.
· When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable
results.
Caution:
1. During repair or tests, minimum distance of 13cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.
2. A "CLASS 1 LASER PRODUCT" label is affixed to the
bottom of the player.
3. The triangular label is attached to the mechanism
unit frame.
4. Specifications of Laser Diode
Specifications of laser radiation fields to which human access is possible during service.
Wavelength
=
800 nanometers
CLASS 1
LASER PRODUCT
4
DEH-P6400R
2. EXPLODED VIEWS AND PARTS LIST
2.1 PACKING
10
14
16
13
1
9
12
15
2
7
5
6
4
3
8
11
5
DEH-P6400R
- Owner's Manual, Installation Manual
Part No.
Language
CRD3513
English, Spanish
CRD3514
German, French
CRB3515
Italian, Dutch
CRD3529
English, Spanish, German, French, Italian, Dutch
1 Cord Assy
CDE6435
2 Accessory Assy
CEA3062
3 Screw
BPZ20P060FZK
4 Screw
CBA1002
5 Handle
CNC5395
6 Earth Plate
CNC9450
7 Bush
CNV3930
*
8 Polyethylene Bag
E36-615
9 Polyethylene Bag
CEG-162
10 Carton
CHG4628
11 Contain Box
CHL46283
12 Protector
CHP2251
13 Protector
CHP2252
14 Inner Box
CHW1754
15-1 Owner's Manual
CRD3513
15-2 Owner's Manual
CRD3514
15-3 Owner's Manual
CRD3515
15-4 Installation Manual
CRD3529
*
15-5 Caution Card
CRP1207
*
15-6 Passport
CRY1013
*
15-7 Warranty Card
CRY1157
15-8 Polyethylene Bag
CEG1116
16 Case Assy
CXB3520
Mark No. Description
Part No.
Mark No. Description
Part No.
- PACKING SECTION PARTS LIST
NOTE:
- Parts marked by "*" are generally unavailable because they are not in our Master Spare Parts List.
- Screws adjacent to
mark on the product are used for disassembly.