ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER ELECTRONIC NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2000
c
Component
Model
Service manual
Remarks
STEREO CD TUNER
XC-F10
RRV2319
STEREO POWER AMPLIFIER
M-F10
RRV2321
SPEAKER SYSTEM
S-F10-LRW
RRV2330
STEREO CASSETTE DECK
CT-F10
RRV2308
This manual.
Type
Model
Power Requirement
CT-F10
ZVYXJ
DC power supplied from other system component
CT-F10
RRV2308
1. SAFETY INFORMATION ...................................... 2
2. EXPLODED VIEWS AND PARTS LIST ................ 3
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM .... 8
4. PCB CONNECTION DIAGRAM .......................... 14
5. PCB PARTS LIST ............................................... 18
6. ADJUSTMENT .................................................... 20
CONTENTS
7. GENERAL INFORMATION ................................ 25
7.1 DIAGNOSIS ................................................. 25
7.1.1 DISASSEMBLY ...................................... 25
7.1.2 POWER ON SEQUENCE ...................... 26
7.2 PARTS ......................................................... 27
7.2.1 IC ............................................................ 27
8. PANEL FACILITIES AND SPECIFICATIONS .... 28
TZZR JUNE 2000 Printed in Japan
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
STEREO CASSETTE DECK
Remarks
÷ This products are component of systems. This product does not operate normally by
itself. Please connect it to the STEREO CD TUNER XC-F10 and the STEREO POWER
AMPLIFIER M-F10 for adjustment and operation inspection.
¶ This product is a system(s) component.
Be sure to connect it to the prescribed system component(s), otherwise damage may
result.
2
CT-F10
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual do-it-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause
cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 Proposition 65
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols
(fast operating fuse) and/or
(slow operating fuse) on PCB indicate that replacement parts must
be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible
(fusible de type rapide) et/ou
(fusible de type lent) sur CCI indiquent que les pièces
de remplacement doivent avoir la même désignation.
ANY MEASUREMENTS NOT WITHIN THE LIMITS
OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL
SHOCK HAZARD AND MUST BE CORRECTED BEFORE
RETURNING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related characteristics. These are
often not evident from visual inspection nor the protection
afforded by them necessarily can be obtained by using
replacement components rated for voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this Service Manual.
Electrical components having such features are identified
by marking with a
on the schematics and on the parts list
in this Service Manual.
The use of a substitute replacement component which does
not have the same safety characteristics as the PIONEER
recommended replacement one, shown in the parts list in
this Service Manual, may create shock, fire, or other hazards.
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER Service
Manual. A subscription to, or additional copies of, PIONEER
Service Manual may be obtained at a nominal charge from
PIONEER.
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service
technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground (water
pipe, conduit, etc.) by connecting a leakage current tester
such as Simpson Model 229-2 or equivalent between the
earth ground and all exposed metal parts of the appliance
(input/output terminals, screwheads, metal overlays, control
shaft, etc.). Plug the AC line cord of the appliance directly
into a 120V AC 60Hz outlet and turn the AC power switch
on. Any current measured must not exceed 0.5mA.
(FOR USA MODEL ONLY)
Leakage
current
tester
Reading should
not be above
0.5mA
Device
under
test
Test all
exposed metal
surfaces
Also test with
plug reversed
(Using AC adapter
plug as required)
Earth
ground
AC Leakage Test
3
CT-F10
2.1 PACKING
1
Pad Front
AHA7295
2
Pad Rear
AHA7296
3
Packing Case
AHD7899
4
Operating Instructions
ARE7257
(Spanish/Portuguese/Dutch/Swedish/
English/French/German/Italian)
NSP
5
Warranty Card
ARY7022
÷ PACKING PARTS LIST
Mark No.
Description
Part No.
2. EXPLODED VIEWS AND PARTS LIST
NOTES:
· Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
· The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
· Screws adjacent to mark on the product are used for disassembly.
Mark No.
Description
Part No.
6
Polyethylene Bag
Z21-038
(0.03
× 230 × 340)
7
Mirror Mat Sheet
Z23-026
(550x550x0.5)
8
Spacer MD TC
AHB7038
9
Stand A Assy
AXG7096
10
Stand B Assy
AXG7097
1
8
9
10
2(1/2)
2(2/2)
3
7
4
5
6
FRONT
4
CT-F10
A
B
C
F
F
27
9
13
26
23
31
31
31
4(2/2)
4(1/2)
11
1
8
5
24
17
24
3(1/2)
3(2/2)
29
31
31
22
21
5
28
7
10
14
16
25
31
31
32
32
30
31
6
12
31
31
11
18
31
31
19
2
33
15
15
20
20
Refer to "2.3
DECK MECHANISM
UNIT"
A
B
H
G
C
G
H
2.2 EXTERIOR
5
CT-F10
÷ EXTERIOR PARTS LIST
Mark No.
Description
Part No.
1
MAIN ASSY
AWU7571
2
SIDE ASSY
AWU7572
3
ILLUMI ASSY
AWU7573
4
PANEL ASSY
AWU7574
5
16P FFC/30V(J2701)
ADD7228
6
Cord With Plug(J2001)
ADE7058
7
Deck Mechanism Unit
TN-708CR-142R
NSP
8
Bottom Chassis MDTC
ANA7108
9
Sub Chassis
AND7037
10
TC Spring
ABH7190
11
Leg
AEB7090
12
FL Holder
AMR7312
13
TC Flap Holder
AMR7315
14
Illumination Holder
AMR7317
15
Button TC
AAD7583
16
TC Flap
AAK7759
17
Display Window TC
AAK7768
18
Rear Cap MD TC
AAK7772
19
Fl Window MDTC
AAK7793
20
Lens MD TC
AAK7838
21
FL Cover
AAK7841
22
Illuminate Lens
AAK7842
23
Sub Panel TC
AAP7070
24
Side Line
AAP7074
25
Screw
ABA7062
26
Bottom Base TC
AMA7018
27
Top Panel TC
AMB7701
NSP
28
Name Label(Pap)TC/ZV
AAL7252
29
Connector Label TC/E
ARW7095
30
Screw
BBZ30P080FMC
31
Screw
BPZ30P080FZK
32
Screw
PMZ30P030FMC
33
Screw
VBZ30P100FZK