CP-81B-K
CP-81B-MK
FRRD-235-A_CP-81_En.book
1
2
En
Thank you for buying this Pioneer product.
Please read through these operating instructions for proper assembly and use. After you have finished reading the instructions, put them
away in a safe place for future reference.
This speaker stand can be used only with the following Pioneer speaker systems: S-81B-LR-K, S-81B-LR-QL, or S-81B-LR-W.
Before you start
Before setting up your speaker system, we recommend reading
the operating instructions for your system thoroughly.
· Only use the screws supplied when fixing the speaker to the
speaker stand.
· Do not place the stand on an unstable and/or sloping surface.
The stand and speaker may fall and cause injury.
· Do not use with any speaker system other than the one for
which the unit was designed. The stand may collapse and be
damaged and/or the speaker may fall and cause injury.
· When moving the speaker and stand, first remove the speaker
from the stand, and then move the stand, holding it by the
stems.
· Place the stand on a stable, level surface; placing the stand on
an unstable surface can be dangerous.
· Pioneer assumes no liability whatsoever for damages
resulting from assembly, improper mounting, insufficient
reinforcement, misuse of the product, acts of nature, etc.
Names of Parts
Screw holes for
securing speaker
Speaker support
Stand stems
Stand base
FRRD-235-A_CP-81_En.book
2
3
En
English
Attaching speakers to the stands
A medium Phillips screwdriver is required for assembling the
speaker stand and for attaching the speaker.
Assembling the speaker stands
Assemble the speaker stands as illustrated below.
Align the screw holes on the stand base and speaker support
with the screw holes in the three stems, then insert the
screws and tighten.
· Make sure you assemble the stand on a flat surface that is
relatively soft (such as a carpet).
· Make sure the screws are inserted in the screw holes as
shown above (with the screw head hidden) when securing the
speaker. Improper setup could result in damage or injury if the
speaker falls from the stand.
When using the spikes
This speaker stand includes spikes that you can use to isolate the
speaker from the floor. Spikes are recommended when placing
the stand on a thick carpet (for added stability), or for better sound
when placing the stand on a hard reverberant surface (such as a
concrete or wood floor). Use the supplied spike bases to avoid
scratching the floor or other surface where the stand is placed.
1
Twist the spikes into the threaded metal inserts
embedded in the bottom of the stand base.
2
Set the spike bases in the positions where the points of
the three spikes will strike when the speaker stand is set
down.
3
Set the speaker stand on the spike bases and check to
confirm the speaker stand does not rock.
· Note that these spikes are sharp metal and can cause damage
to flooring. Make sure to lay down a cloth or suitable base
before setting up.
· Always use the spike bases as shown, with the indented
surface facing up to receive the spike point.
When using the non-skid pads
30 mm
(1 3/16 in.)
Black
30 mm
(1 3/16 in.)
Black
Speaker
support
Stand
stems
Stand
base
Spikes [SBA6080]
Spike bases [SBG6001]
Screws (Bind head, M6 x L30)
[SBA6089]
Screws (Bind head, M6 x L30)
[SBA6089]
Please note that sunken
screw holes are provided in
the speaker support.
If you do not use the spike bases when placing the
speakers, the spikes may cause damage to the floor. If
you plan on using the spikes we highly recommend to
use the spike bases.
Stand base
Stand base
FRRD-235-A_CP-81_En.book
3
4
En
When using speaker spikes:
To avoid accident or injury, please use screws to secure the
speaker to the speaker stands. Note that there are fastening nuts
provided on the speaker base (see below).
Secure the speaker to the speaker support using the washer,
spring washer and the 50 mm (2 in.) screws as shown below.
When not using speaker spikes:
To avoid accident or injury, please use screws to secure the
speaker to the speaker stands. Note that there are fastening nuts
provided on the speaker base (see below).
Secure the speaker to the speaker support using the washer,
spring washer and the 40 mm (1 5/8 in.) screws as shown below.
50 mm
(2 in.)
Black
Speaker
support
Fastening nut
Screw holes for
securing speaker
Washer [SBE1043]
Spring washer [SBE1042]
Screws (Bind head, M4 x L50)
[SBA6012]
Speaker
spike base
40 mm
(1 5/8 in.)
Black
Speaker
support
Fastening nut
Screw holes for
securing speaker
Washer [SBE1043]
Spring washer [SBE1042]
Screws (Bind head, M4 x L40)
[SBA6011]
FRRD-235-A_CP-81_En.book
4
5
En
English
Stand maintenance
· Use a polishing cloth or dry cloth to wipe off dust and dirt.
· If the stand is very dirty, use a soft cloth dipped in some neutral
cleanser diluted five or six times with water. Finally, wipe again
using a dry cloth. Do not use furniture wax or cleaners.
· Never use thinners, benzine, insecticide sprays and other
chemicals on or near the stand, since these will corrode the
surfaces.
Specifications
External dimensions . . . . . . 310 (W) mm x 604 (H) mm x 404 (D) mm
12 1/4 (W) in. x 23 13/16 (H) in. x 15 15/16 (D) in.
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5 kg /14 lbs. 6 oz.
Supplied accessories
Stand base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Speaker support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Stand stems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Spikes [SBA6080] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Spike bases [SBG6001] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Non-skid pads [FREC067] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Screws (Bind head, M6 x L30) [SBA6089] . . . . . . . . . . . . . . . . . . . . . 24
Screws (Bind head, M4 x L40) [SBA6011] . . . . . . . . . . . . . . . . . . . . . . 4
Screws (Bind head, M4 x L50) [SBA6012] . . . . . . . . . . . . . . . . . . . . . . 4
Spring washers [SBE1042] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Washers [SBE1043] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Operating instructions [FRRD-235] . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
· Specifications and design subject to possible modification
without notice, due to improvements.
· The product number are listed above in square brackets.
Published by Pioneer Corporation.
Copyright © 2008 Pioneer Corporation.
All rights reserved.
Replacement part numbers
Part name
Part no.
· Protector (top)
SHA6182
· Protector (middle)
SHA6184
· Protector (bottom)
SHA6183
· Protector (stand base)
SHA6188
· Protector (speaker support)
SHA6185
· Packing case (CP-81B-K only)
SHG6402
· Packing case (CP-81B-MK only)
SHG6403
· Polyethylene bag (stand base)
SHL6092
· Polyethylene bag (speaker support)
SHL6038
· Polyethylene bag (stand stems)
SHL6093
· Protection sheet (stand base)
SHC6087
· Protection sheet (speaker support)
SHC6015
· Protection sheet (stand stems)
SHC6088
FRRD-235-A_CP-81_En.book
5