PIONEER CP-7EX - Owner's Manual Immediate Download

CP-7EX

Speaker Stand / Socle d'enceinte / Lautsprecherständer /

Base per diffusori / Luidsprekerstandaard / Soportes de altavoz /

Suporte para colunas / Högtalarstativ / Højttalerstativ /

Høyttalerstativ / Kaiutinjalusta /

Thank you for buying this Pioneer product. This speaker

stand should only be used with the S-7EX Pioneer speaker

system. Please read through these operating instructions for

proper assembly and use. After you have finished reading the

instructions, put them away in a safe place for future

reference.

Before you start

Before setting up your speaker system, we recommend

reading the operating instructions for your system thor-

oughly.

· Only use the screws supplied when fixing the speaker to

the speaker stand.

· Do not place the stand on an unstable and/or sloping

surface. The stand and speaker may fall and cause

injury.

· Do not use with any speaker system other than the one

for which the unit was designed. The stand may collapse

and be damaged and/or the speaker may fall and cause

injury.

· When moving the speaker and stand, first remove the

speaker from the stand, and then move the stand,

holding it by the two stems.

Installing the speaker stands

Place the stand on a stable, level surface; placing the stand

on an unstable surface can be dangerous.

Adjust the position as necessary to obtain optimal sound

from your system.

· Pioneer assumes no liability whatsoever for damages

resulting from assembly, improper mounting, insuffi-

cient reinforcement, misuse of the product, acts of

nature, etc.

Assembling the speaker stands

Assemble the speaker stands as illustrated below. Please

note that a flathead screwdriver will be necessary for

assembly. The following illustration shows the fully assem-

bled speaker stand:

Speaker support

Stand base

Stand stems

Screw slots

for securing

speaker

Align the screw slots on the stand base and screw

holes on the speaker support with the screw holes in

the two stems, then insert the screws and tighten.

The screw slots allow you to fine-tune the positioning of the

speaker.

55 mm

Black

(SBA6054)

40 mm

Black

Please note that sunken

screw holes are provided

in the speaker support.

(SBA6051)

Screws (Bind head, M6xL40)

Nut

Spike (SBA6053)

Spike base

(SLA1057)

Screws (Bind head, M6xL55)

Speaker

support

Stand

base

Stand

stems

· Make sure you assemble the stand on a flat surface that

is relatively soft (such as a carpet).

· Make sure the screws are inserted in the screw holes as

shown above (with the screw head hidden) when

securing the speaker. Improper setup could result in

damage or injury if the speaker falls from the stand.

English

Using the spikes

The speaker stand includes spikes that you can use to isolate

the speaker from the floor. Spikes are recommended when

placing the stand on a thick carpet (for added stability), or for

better sound when placing the stand on a hard reverberant

surface (such as a concrete or wood floor). Use the supplied

spike bases to avoid scratching the floor or other surface

where the stand is placed.

Spike

Stand base plate

Nut

Attach the spikes to the nuts provided.

Attach all four spikes to the threaded metal inserts

at the base of the speaker stand.

Choose the location for speaker placement then put

the spike bases on the floor.

Place the stand so that the spikes are resting on the

spike bases on the floor.

Before placing the speaker on the speaker stand, make sure

the stand is stable and resting squarely on all four spikes.

· Note that these spikes are sharp metal and can cause

damage to flooring. Make sure to lay down a cloth or

suitable base before setting up.

· The spike bases should be placed as shown below (with

the depression on the top side).

· Make sure to use the spike bases provided to avoid

damaging the surface where you place the stand.

Attaching a speaker to the stand

To avoid accident or injury, please use screws to secure the

speaker to the speaker stand. Note that there are fastening

nuts provided on the speaker base (see below). Secure the

speaker to the speaker support using the washer, spring

washer and the 60 mm screws as shown below.

(SBA6058)

Speaker

base

Speaker

support

Washers (SBE6008)

Fastening nuts

Screws

(Bind head, M6xL60)

60 mm

Black

Spring washer

(SBE6007)

Screw slots

for securing

speaker

Cabinet and stand maintenance

· Use a polishing cloth or dry cloth to wipe off dust and

dirt.

· If the cabinet or stand is very dirty, use a soft cloth

dipped in some neutral cleanser diluted 5 or 6 times

with water. Finally, wipe again using a dry cloth. Do not

use furniture wax or cleaners.

· Never use thinners, benzine, insecticide sprays and

other chemicals on or near the cabinet or stand, since

these will corrode the surfaces.

Published by Pioneer Corporation.

If you want to dispose this product, do not mix it with

general household waste. There is a separate collection

system for used electronic products in accordance with

legislation that requires proper treatment, recovery and

recycling.

Private households in the 25 member states of the EU, in

Switzerland and Norway may return their used electronic

products free of charge to designated collection facilities or to a

retailer (if you purchase a similar new one).

For countries not mentioned above, please contact your local

authorities for the correct method of disposal.

By doing so you will ensure that your disposed product under-

goes the necessary treatment, recovery and recycling and thus

prevent potential negative effects on the environment and

human health.

Part name

· Protector (Top)

· Protector (Middle)

· Protector (Bottom)

· Packing case

· Protection sheet

Replacement part numbers

Part no.

SHA6101

SHA6102

SHA6103

SHG6148

SHC6048

SHC6049

SHC6050

Specifications

External dimensions ............... 498 (W) x 310 (H) x 412 (D) mm

Weight .............................................................................. 14.0 kg

Supplied accessories

Stand base plate ........................................................................ 1

Speaker support ......................................................................... 1

Stems .......................................................................................... 2

Spikes (with attached nuts) [SBA6053] ................................... 4

Spike bases [SLA1057] .............................................................. 4

Screws (Bind head, M6xL55) [SBA6051] ................................. 6

Screws (Bind head, M6xL60) [SBA6058] ................................. 2

Screws (Bind head, M6xL40) [SBA6054] ................................. 6

Spring washers [SBE6007] ........................................................ 2

Washers [SBE6008] ................................................................... 2

These operating instructions [SRD6046] ................................. 1

· Specifications and design subject to possible modifica-

tion without notice, due to improvements.

· The product number are listed above in square brackets.

FrançaisFrançais

Nous vous remercions pour l'achat de ce produit Pioneer. Ce

socle d'enceinte doit être utilisé uniquement avec l'enceinte

acoustique S-7EX de Pioneer. Veuillez lire attentivement ce

mode d'emploi pour assembler et utiliser correctement le

produit. Après avoir lu ces explications, rangez-les dans un

endroit sûr pour vous y référer éventuellement à l'avenir.

Avant de commencer

Avant d'installer les enceintes acoustiques, nous vous

conseillons de lire attentivement le mode d'emploi qui les

accompagne.

Attention

· Utilisez uniquement les vis fournies pour fixer l'enceinte

sur le socle d'enceinte.

· Ne placez pas le socle sur une surface instable et/ou

glissante, car le socle et l'enceinte pourraient tomber et

provoquer des blessures.

· N'utilisez avec aucune autre enceinte que celle pour

laquelle ce socle a été conçu. Le socle pourrait se

renverser et être endommagé et/ou l'enceinte pourrait

tomber et provoquer des blessures.

· Avant de déplacer l'enceinte et le socle, déposez d'abord

l'enceinte, puis déplacez le socle en le tenant par ses

deux montants.

Installation des socles d'enceinte

Placez le socle sur une surface stable et horizontale; il serait

dangereux de le poser sur une surface instable.

Ajustez la position selon les besoins de manière à obtenir de

votre enceinte un son optimal.

· Pioneer n'assume aucune responsabilité en cas de

dégâts, découlant d'une assemblage ou d'un montage

inadéquat, d'un renforcement insuffisant, d'une

utilisation inapproprié du produit, de catastrophes

naturelles, etc.

Assemblage des socles d'enceinte

Assemblez les socles d'enceinte comme illustré ci-dessous.

Notez qu'un tournevis à tête plate est requis pour cet assem-

blage. L'illustration suivante présente le socle d'enceinte à

l'état assemblé.

Rainures de vis

pour fixation

de l'enceinte

Support

d'enceinte

Base du socle

Montants

du socle

Faites correspondre les rainures de vis sur la base du

socle et les orifices de vis sur le support d'enceinte avec

les orifices de vis dans les deux montants, puis insérez les

vis et serrez-les.

Les rainures de vis permettent d'ajuster avec précision le

positionnement de l'enceinte.

55 mm

Noir

(SBA6054)

40 mm

Noir

Notez que des orifices

pour vis noyée sont prévu

sur le support

(SBA6051)

Vis (tête intégrée, M6xL40)

Écrou

Pointe de

découplage

(SBA6053)

Vis (tête intégrée, M6xL55)

Support

d'enceinte

Base du

socle

Montants

du socle

Base pour pointe de

découplage (SLA1057)

Attention

· Prenez soin d'assembler le socle sur une surface plate

qui soit relativement souple (comme un tapis).

· Lors de la fixation de l'enceinte, prenez soin que les vis

soient insérées dans les orifices de vis comme illustré ci-

dessus (leur tête étant noyée). Une installation

inadéquate pourrait provoquer des dégâts ou des

blessures si l'enceinte devait tomber de son socle.

English