ENG/MASTER 96
ENGLISH
ESPAÑOL
DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
AUDIO VIDEO SELECTOR
SÉLECTEUR AUDIO/VIDÉO
This product conforms to new cord colors.
Los colores de los cables de este producto se conforman con un nuevo
código de colores.
Dieses Gerät entspricht den neuen kabelfarben.
Le code de couleur des câbles utilisé pour ce produit est nouveau.
Questo prodotto è conforme ai nuovi codici colori.
Operation Manual
CD-VS33
Mode d'emploi
1
20080403CD-VS33-E.Q3.3E
08.4.22 9:50 AM
Page 1
2
1
Contents
Before Using this Product ........................ 2
About this Product ............................................ 2
Precaution .......................................................... 2
Connecting the Units ................................ 3
Connecting the Power Cord
and Controller Unit .................................... 4
Connecting the System (1) ................................ 5
Connecting the System (2) ................................ 7
Connecting the Audio/Video equipment............ 9
Installation ................................................ 10
Installing Hide-away Unit .............................. 10
Installing Controller Unit ................................ 11
Part Names And Applications .............. 14
Controller Unit ................................................ 14
Hide-away Unit ................................................ 15
Specifications .......................................... 16
ENG/MASTER 96
20080403CD-VS33-E.Q3.3E
08.4.22 9:50 AM
Page 2
Before Using this Product
About this Product
This product is a rear-seat audio-video selector that enables you to switch the display
between audio and video.
I When using this product
We recommend that you familiarize yourself with the functions and their operation by
reading through the manual before you begin using this product. It is especially important
that you read and observe the "Precaution" on this page and in other sections.
Precaution
· Keep this manual handy as a reference for operating procedures and
precautions.
· Protect this product from moisture.
· Do not set a high volume level when using headphones to listen. Listening to high vol-
umes for extended periods of time can have an adverse effect on hearing.
2
ENGLISH
ESPAÑOL
DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
ENG/MASTER 96
3
WARNING
· Handling the cord on this product or cords associated with accessories sold with the
product may expose you to chemicals listed on proposition 65 known to the State of
California and other governmental entities to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
· Connect the product to a display that cannot be seen by the driver. If the display can be
installed only where it is visible to the driver, use a display that can detect the ON/OFF
status of the parking brake, and be sure to install the display correctly so that it always
works in conjunction with the parking brake switch.
· To avoid the risk of accident and the potential violation of applicable laws, this product
is not for use with a video screen that is visible to the driver.
· In some countries or states the viewing of images on a display inside a vehicle even by
persons other than the driver may be illegal. Where such regulations apply, they must
be obeyed.
20080403CD-VS33-E.Q3.3E
08.4.22 9:50 AM
Page 3
4
3
Connecting the Units
Note:
· This product is for vehicles with a 12-volt battery and negative grounding. Before installing it in a
recreational vehicle, truck, or bus, check the battery voltage.
· To avoid shorts in the electrical system, be sure to disconnect the battery cable before beginning
installation.
· After completing installation and wiring, double check that there are no mistakes. Re-install any
parts removed from the car during installation, then connect the battery negative terminal.
· Refer to the owner's manual for details on connecting the various cords of the
power amp and other units, then make connections correctly.
· Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
· Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, handbrake
and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the
insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the
vehicle body.
· Do not shorten any leads. If you do, the protection circuit may fail to work when it should.
· Never feed power to other equipment by cutting the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating.
· When replacing a fuse, be sure to use only a fuse of the rating prescribed on the fuse holder.
· Always grip the Controller unit when connecting an RCA pin plug.
ENG/MASTER 96
20080403CD-VS33-E.Q3.3E
08.4.22 9:50 AM
Page 4
Connecting the Power Cord and Controller Unit
4
ENGLISH
ESPAÑOL
DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
ENG/MASTER 96
5
Red
To electric terminal controlled by
ignition switch (12V DC) ON/OFF.
Black (ground)
To vehicle (metal) body.
Hide-away unit
Controller unit
Route the controller unit
cord inside the slot groove
on the controller unit rear
side. Do not pull strongly,
excessively bend or stretch
the cord.
Fuse holder (1 A)
3 m
2 m
2 m
Controller unit rear side
Groove
Cord
20080403CD-VS33-E.Q3.3E
08.4.22 9:50 AM
Page 5